BENDIX TCH-002-006 User manual

Type
User manual

BENDIX TCH-002-006 is a useful tool for manually caging and/or un-caging (releasing) a Bendix® Air Disc Brake Spring Brake Actuator. It helps ensure the parking brake is securely engaged or disengaged, ensuring vehicle safety. The device features a release bolt that can be rotated clockwise to cage the parking brake and counterclockwise to un-cage it. It requires an air pressure of 100 psi to be applied to the parking brake port during the caging and un-caging process.

BENDIX TCH-002-006 is a useful tool for manually caging and/or un-caging (releasing) a Bendix® Air Disc Brake Spring Brake Actuator. It helps ensure the parking brake is securely engaged or disengaged, ensuring vehicle safety. The device features a release bolt that can be rotated clockwise to cage the parking brake and counterclockwise to un-cage it. It requires an air pressure of 100 psi to be applied to the parking brake port during the caging and un-caging process.

The following procedure is for manually caging and/or un-caging (releasing) a Bendix
®
Air Disc Brake Spring
Brake Actuator.
Un-Caging (releasing) the Parking Brake
1) Install the spring brake actuator on the air disc brake (if not previously installed). Refer to service data sheet
SD-23-7541 (BW7308). See Figure 1b.
2) Connect a regulated air line to parking brake port (12) of the actuator (if not connected previously). See
Figure 1a.
3) Gradually supply 100 psi of air pressure to the parking brake port (12) of the actuator.
4) Rotate the release bolt clockwise until resistance is encountered.
5) Seat the release bolt in the un-caged position by applying a torque of 50 lb-ft. The release bolt and push
rod should be in the position shown in Figure 2.
6) With hands clear of moving parts, slowly release the air pressure to the parking brake port (12). Be sure to
exercise caution to prevent pinching of ngers.
Technical Bulletin
Bulletin No: TCH-002-006 Effective Date: 11/1/2007 Cancels: N/A Page: 1 of 2
Subject: Bendix
®
Air Disc Brake Spring Brake Actuator Caging Procedure
© 2007 Bendix Commercial Vehicle Systems LLC 11/2007. All rights reserved. Printed in U.S.A.
Service
Housing
Spring Brake
Housing
Parking Brake (12)
Service Port (11)
Service Housing
Spring Brake Housing
Release Bolt
Push Rod
Figure 1a - Spring brake shown in the caged position.
Figure 1b - Air disc brake assembly
Parking Brake (12)Service Port (11)
Release Bolt
Push Rod
Figure 2 - Spring brake shown in the un-caged (released) position.
(over)
Caging the Parking Brake
1) Connect a regulated air line to parking brake port (12) of the actuator (if not connected previously).
2) Gradually supply 100 psi of air pressure to the parking brake port (12) of the actuator.
3) Rotate the release bolt counterclockwise until resistance is encountered.
4) Seat the release bolt in the caged position by applying torque of 25 lb-ft. The release bolt and push rod
should be in the position shown in Figure 1a.
5) With hands clear of moving parts, slowly release the air pressure to the parking brake port (12). Be sure to
exercise caution to prevent pinching of ngers.
Notes
As always, follow all recommended safety procedures when performing any service on your vehicle.
1) The release bolt cannot be removed from the parking brake.
2) The nut is permanently attached to the release bolt.
3) Unless a vehicle must be moved in an emergency situation, NEVER ATTEMPT to Cage or Un-Cage the
parking brake without applying air pressure (100 psi) to the parking brake port (12). This practice may
damage the caging bolt and/or the parking brake which could result in the need to replace the spring brake
actuator.
4) DO NOT USE an impact wrench to rotate the caging bolt.
5) Please refer to service data sheet SD-23-7541 (BW7308) for complete service instructions for Air Disc Brakes
products from Knorr Bremse, Bendix and Bendix Spicer Foundation Brake.
  • Page 1 1
  • Page 2 2

BENDIX TCH-002-006 User manual

Type
User manual

BENDIX TCH-002-006 is a useful tool for manually caging and/or un-caging (releasing) a Bendix® Air Disc Brake Spring Brake Actuator. It helps ensure the parking brake is securely engaged or disengaged, ensuring vehicle safety. The device features a release bolt that can be rotated clockwise to cage the parking brake and counterclockwise to un-cage it. It requires an air pressure of 100 psi to be applied to the parking brake port during the caging and un-caging process.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI