2. 2N
  3. Voice Alarm Station

2N Voice Alarm Station, Voice Installation guide

  • Hello! I am an AI chatbot trained to assist you with the 2N Voice Alarm Station Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
2N
®
Voice Alarm Station
2N
®
Lift1
Installation Manual
Version 1.0.0 www.2n.cz
Voice Alarm Station
Description
The extends the with an 2N
®
Voice Alarm Station 2N Lift1
®
/ 2N SingleTalk
®
audiounitinstalledonthecabinroofandunderthecabin.Itisa"audio panel switch
"thatinterconnects withoneortwoaudiounits.2N Lift1
®
/ 2N SingleTalk
®
2N Lift1 - 919640, 919640X
®
2N SingleTalk -
®
913640
EN
Operation
Use"Presstocall"toactivatethedeviceandsetupacalltothenumbersetin2N
®
(ALARMbuttonmemory-011to016). Lift1/ 2N SingleTalk
®
Caution
Theaudiounitdoesnotcontainanycall-setupindicatingLED.TheLEDon
is illuminated to indicate call setup and2N Lift1
®
/ 2N SingleTalk
®
confirmation.
Itisnecessarytowaitforapprox.30sforcallsetupfromanotheraudio
unit. The switch remembers the last alarm-calling audio unit and when
alarmisgeneratedfromanotheraudiounitwithin30s,thecallissetup
fromtheaudiounitthatwasthelasttomakethealarmcall.
Mounting
Remove the connectors on the ALARM inversion and programming jumpers on 2N
®
.Usethe4screwstoloosenandmovedownwardstheaudio Lift1/ 2N SingleTalk
®
unit.Disconnectthespeakerand(external)microphone.
Connectthecableconnectorsincludedinthedeliverytothemicrophoneandspeaker
connectorson (themicrophoneandspeakerconnectors2N Lift1
®
/ 2N SingleTalk
®
have different sizes and cannot be interchanged due to the audio unit cover
pictograms).Replacetheaudiounitcover,moveitupwardsandtightenthe4screws.
Putthe6-pinconnectorontheALARMinversionandprogrammingjumpers(seethe
figurebelow).
Removethecoverfromtheswitch.Interconnecttheswitchandthe2N Lift1
®
/ 2N
®
audiounit withthecableincludedinthedelivery.SingleTalk
Connect the microphone and speaker from 2N Lift1
®
/ 2N SingleTalk
®
in the
point-switch.Thespeakerandmicrophoneconnectorsaremarked(SPKandMIC).Put
theconnectorsonthejumpersintheswitch.Theconfigurationisthesameasin2N
®
(alsomarkedontheswitchboard).Pull thecablesthrough Lift1/ 2N SingleTalk
®
theholes.
Warning
Makesurethatthe6-pinconnectioniscorrecttoavoidproductdamage.
Makesurethattheyellowwireisup(whenviewingtheaudiounit).
Caution
In the case of a cable version of , an2N Lift1 / 2N SingleTalk
® ®
external microphone should be connected into the microphone input on
thecable-switch.Ifyoudonothaveacableversion,thisinputshouldbe
free.
Breakoutcableholesintheswitchuppercover.Thenreplacethecover.Thereare2
RJ12connectorsonthepoint-switchsideforaudiounitconnection.Interconnectthe
audiounitandtheswitchusingthecablesupplied.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
2N TELEKOMUNIKACE a.s.
Modřanská 621, 143 01 Prague 4, Czech Republic
Tel.: +420 261 301 500, Fax: +420 261 301 599
E-mail: sales@2n.cz
Web: www.2n.cz
LŠ 2142v1
/