Bloomfield 9010 User manual

Bloomfield
Brand
Bloomfield
Model
9010
Type
User manual

This manual is also suitable for

Bloomfield 9010, your new coffee brewer, boasts advanced features for an exceptional coffee experience. With its solenoid valve retrofit kit, it ensures precise water flow control, enhancing the flavor and aroma of every cup. Installation is a breeze with clear instructions and included parts. Enjoy a perfect brew with Bloomfield 9010.

Bloomfield 9010, your new coffee brewer, boasts advanced features for an exceptional coffee experience. With its solenoid valve retrofit kit, it ensures precise water flow control, enhancing the flavor and aroma of every cup. Installation is a breeze with clear instructions and included parts. Enjoy a perfect brew with Bloomfield 9010.

BLOOMFIELD INDUSTRIES SERVICE INSTRUCTIONS
2 Erik Circle
Verdi, Nevada 89439 SOLENOID VALVE RETROFIT KIT
(775) 345-0444 84571 (120V) and 84572 (220/240V)
A. APPLICABILITY
This kit replaces the solenoid valve and faucet supply tube on automatic brewer models:
Koffee-King™ 8540 8572 Domestic and Export
Integrity™ 9010 9012 Domestic and Export
B. INSTRUCTIONS
CAUTION: ELECTRIC SHOCK HAZARD
Unplug brewer before beginning conversion
1. REMOVE EXISTING SOLENOID (See fig. B.1 and B.2)
a. Unplug brewer and shut off water supply. Open faucet to bleed off water
pressure.
b. Remove TOP PANEL, FRONT PANEL and SOLENOID ACCESS DOOR.
c. Disconnect wires to solenoid. Remove silicone SUPPLY HOSE from solenoid.
d. Disconnect FAUCET SUPPLY TUBE from solenoid and faucet shut-off valve.
e. Remove BRASS NUT from INLET FITTING.
Lift solenoid / timer / bracket
assembly from mounting clip.
f. Loosen screws on bottom of solenoid and
separate solenoid from bracket.
Remove solenoid and fittings from cabinet.
Reinstall bracket on mounting clip.
p/n 74535 Rev.(-) 040500cps page 1 Of 3
Note::
Integrity™ shown
Koffee-King™ similar
ACCESS DOOR
Fig. B.2
FAUCET SUPPLY
TUBE
SOLENOID
ASSEMBLY
REMOVE SHADED COMPONENTS
• SOLENOID ACCESS DOOR
• SOLENOID AND FLOW CONTROL
• INLET FITTING, TEE & ADAPTERS
DISCONNECT
Fig. B.1
B. INSTRUCTIONS (continued)
2. INSTALL NEW SOLENOID (See figure B.3, B.4 and B.5)
a. Attach faucet supply BRAIDED HOSE to SOLENOID.
Push the hose fully onto the bypass outlet (the side
without a solenoid coil). Install one CLAMP over the
shaft of the outlet, and one CLAMP directly over the
barb of the outlet.
b. Assemble the SOLENOID BRACKET to the new
ACCESS DOOR. Assemble the SOLENOID to the
SOLENOID BRACKET.
c. Route the silicone SUPPLY TUBE through the 3rd
hole (from the front) then out the access door opening.
Attach tube to SOLENOID. Push the tube fully onto
the controlled outlet (the side with the solenoid coil).
d. Route the BRAIDED HOSE through the 1st hole (from
the front). Connect the flare SWIVEL NUT to the end
of the braided hose. Rotate the FAUCET SHUT-OFF
VALVE as needed (approximately 45° and connect the
swivel nut to the valve. Verify all connections are tight.
e. Assemble the ACCESS DOOR / SOLENOID to the cabinet.
f. Turn water supply ON. Check for leaks.
g. Insert BUTTON PLUG in the hole formerly occupied
by the inlet fitting.
h. Reinstall TOP PANEL and FRONT PANEL.
p/n 74535 Rev.(-) 040500cps Page 2 Of 3
Fig.
B.3
Plug unit in and test.
ROTATE FAUCET
SHUT-OFF VALVE 45°
STIC
HOSE TO OUTLET
WITH SOLENOID:
* PUSH HOSE
FULLY AGAINST
VALVE BODY
ROUTE HOSES
AS SHOWN
ATTACH BRAIDED HOSE
TO OUTLET WITHOUT
SOLENOID (BYPASS):
* PUSH HOSE FULLY
AGAINST VALVE BODY
* PLACE FIRST CLAMP
ON OUTLET SHAFT
* CENTER SECOND
CLAMP DIRECTLY OVER
BARB
Fig. B.5
Fig. B.4
PARTS LISTS: KIT NO. 84571 120V BREWER W/FAUCET
ITEM SERV P/N DESCRIPTION QTY
12 84461 BRAIDED HOSE ASSY 1
38 84412 SOLENOID ACCESS DOOR 1
38 84413 SOLENOID BRACKET 1
40 81165 COUPLING, FLARE SWIVEL 1
45 84455 SOLENOID ASSY, 120Vw/BYPASS 1
46 84460 HOSE CLAMP 2
47 8810-12 BUTTON PLUG, ½” DIA 1
AA
SCREW, FLT PHL SS 8-32 x ½” 2
BB SCREW, PAN SLT SS 4mm x 6mm 2
PARTS LIST: KIT NO. 84572 240V BREWER W/FAUCET
ITEM SERV P/N DESCRIPTION QTY
12 84461 BRAIDED HOSE ASSY 1
38 84412 SOLENOID ACCESS DOOR 1
38 84413 SOLENOID BRACKET 1
40 81165 COUPLING, FLARE SWIVEL 1
45 84570 SOLENOID ASSY, 240V w/BYPASS 1
46 84460 HOSE CLAMP 2
47 8810-12 BUTTON PLUG, ½” DIA 1
AA
SCREW, FLT PHL SS 8-32 x ½” 2
BB
SCREW, PAN SLT SS 4mm x 6mm 2
p/n 74535 Rev.(-) 040500cps page 3 of 3
  • Page 1 1
  • Page 2 2
  • Page 3 3

Bloomfield 9010 User manual

Bloomfield
Brand
Bloomfield
Model
9010
Type
User manual
This manual is also suitable for

Bloomfield 9010, your new coffee brewer, boasts advanced features for an exceptional coffee experience. With its solenoid valve retrofit kit, it ensures precise water flow control, enhancing the flavor and aroma of every cup. Installation is a breeze with clear instructions and included parts. Enjoy a perfect brew with Bloomfield 9010.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents