Festivo 50 VL Instructions For Installation And Use Manual

Brand: Festivo

Model: 50 VL

Category: Wine coolers

Type: Instructions For Installation And Use Manual

WINE CABINET 50 VL

INSTRUCTIONS FOR

INSTALLATION AND USE

It is strongly adviced that these instructions

be read carefully prior to the installation

and operation your new freezer.

SAFETY PRECAUTIONS ......................................... 3

STIPULATIONS FOR USE ....................................... 3

BEFORE STARTING TO USE THE CABINET ......... 4

INSTALLING THE WINE CABINET.......................... 4

Location .............................................................. 4

Electric connection ............................................ 5

Balancing ............................................................ 6

Fitting the bottom front plate ............................ 6

Shelves ............................................................... 6

Adjustment of the door ...................................... 6

FUNCTIONAL DESCRIPTION ................................. 7

Functioning of the cooling mechanism .............. 7

SWITCHES AND THERMOSTAT ............................. 8

USING THE WINE CABINET ................................... 8

Switching on ...................................................... 8

Switching off ...................................................... 8

Adjusting the temperature ................................. 8

Sounds produced during operation .................. 9

CLEANING .............................................................. 9

Cleaning the wine cabinet .................................. 9

Cleaning and service ........................................ 10

FUNCTIONAL DISORDERS .................................. 10

Correcting minor disorders .............................. 11

Error messages .................................................11

DISPOSAL OF THE APPLIANCE ........................... 11

CX45 1212

Table of contents

When cleaning the wine cabinet, switch off

the voltage using the main switch and remo-

ve the plug from the socket.

Materials that are liable to explode must not

be kept in the wine cabinet.

The door must not be opened beyond 120

º, because this may cause the hinge bush-

ing to break on hitting the corner of a table

top, for example (see the drawing).

Leave the door open when the appliance

is not in use.

The wine cabinet is suitable for storage of

wines only.

It is intended for use in households. For use

in other establishments, it is necessary to

take into account the separate stipulations

concerning this.

The wine cabinet has been constructed and

tested in accordance with the regulations

and statutes currently in force.

Repairs to the cabinet must only be carried

out by an authorized servicing firm with

training in that field. Incompetent repairs

may cause risk situations for the user or the

surroundings of the appliance.

Safety precautions Stipulations for use

TABLE TOP

Warning!

The appliance contains a small amount

of environment-friendly but flammable

coolant, R600a.

This coolant will not damage the ozone

layer, nor will it cause a greenhouse

effect.

Please check that the coolant piping has

not become damaged during trans-

portation or installation.

Leaking coolant may damage the eyes

or catch fire.

If you notice coolant leakage:





do not allow open fire in the room





take the plug of the appliance out of

the electric socket





ventilate the room for several

minutes





contact the Festivo service organi-

zation.

Warning!

 The air inlet of bottom must not be

covered.

 Ice must not be detached using a

knife or any other mechanical tools.

 Do not damage the coolant pipes.

 Never use electrical appliances insi-

de the appliance unless they are ap-

proved by the manufacturer.

Please read carefully the Instructions for

Installation and Use. They contain important

information about installing, using and

maintaining the appliance.

The manufacturer of the appliance will bear

no responsibility if the directions in the

Instructions for Use are not followed.

Do not start to use the appliance imme-

diately after transportation or after it has

been kept in a cold place, but let it stand in

its final location for a few hours so that the

oil has time to flow down into the compres-

sor.

Note! The appliance must not be situated in

too small a space. This is because in the

event of any coolant leakage in a small

space, an explosive gas mixture could form.

The room space must be at least 4 m

Before starting to use the

appliance

Installation

LOCATION

Room temperature, where the cabinet can

be situated.

Climate range

SN +10 ... +32 °C

N +16 ... +32 °C

ST +18 ... +38 °C

T +18 ... +43 °C

The climate range of the appliance is on

the data plate. The data plate is situated

inside of the cabinet on right side of the

wall.

Situate the appliance to a dry, very well

ventilated room.

Do not situate the cabinet in the imme-

diate vicinity of a radiator, stove or other

heat source.

Do not situate the cooling cabinet in a

small, poorly ventilated place. Faultless

operation of the mechanism requires

good ventilation. The air inlet at the front

of the appliance, below the door, must not

be covered.

NOTE!

Check that the end of the defrost water

pipe A is in the trough on top of the

compressor.

ELECTRIC CONNECTION

The wine cabinet is connected to an eart-

hed (grounded) electric socket (single

phase, 230V, 50 Hz) using the connecting

lead of the appliance. The fuse size for

the socket is 10 A. Any alterations to the

connection method or changing of the

connecting lead must only be done by an

electrician.

The circulation of the condensation air for

the wine cabinet must not be blocked by

any excess length of connecting lead;

instead, this should be allowed to lie on

the floor behind the cabinet, for example.

Do not use an extension cord.

See operational description / air circulati-

on, page 7, picture.

The floor where the cabinet is situated

must be even and horizontal, and at the

same level as the surrounding floor.

In the cooling cabinet, ice formed on the

expansion coil melts automatically and the

resulting water is conducted to the evapo-

ration trough in the compressor area,

from which it evaporates automatically.

If there will be any functional disorder it is

possible that there will be water leakage

under the appliance.

That is why we recommend to install a

protective cover to the floor where the

appliance will be situated.

The floor cover can also be ordered from

Festivo-service.

The cooling cabinet can be situated

against background surface and side sur-

faces, but if its side surface comes next to

another cold storage appliance or an out-

side wall, then a ventilation gap of at least

2 cm must be left between the surfaces

concerned.

No other appliances or furniture must be

fixed to the cabinet, because it has to be

possible to pull it out for cleaning and ser-

vicing.

If the cabinet is situated in corner it must be

noticed that the door opens 90°. So it is

possible to take shelves out of the cabinet.

Min.60mm

BALANCING

Push the wine cabinet into place and

balance it with the aid of the adjusting

legs at the front edge (see illustration).

FITTING THE BOTTOM FRONT PLATE

Fix the bottom front plate in place.

SHELVES OF THE WINE CABINET

The shelves can be removed by lifting

them out.

ADJUSTMENT OF THE DOOR

If it is necessary to adjust the door, the

hinges can be adjusted to some degree

by loosening the fixing screws and mo-

ving the hinges in the depth direction of

the cabinet. When adjusting the hinges,

care must be taken that the door seal

does not get compressed too much.

The compression of the seal should be

even along the whole perimeter of the

door.

If the seal is too compressed on the hin-

ge side, then move the hinges out-

wards. If the seal has become pressed

down, warm it CAREFULLY with a hot-

air blower (hair dryer) and mould it with

the fingers to make it higher.

Adjusting legs

Clamps

FUNCTIONING OF THE COOLING

MECHANISM

The cooling mechanism consists of the

compressor, the condenser and the ex-

pansion coil; these form a closed circuit

in which the compressor circulates the

coolant.

In the expansion coil, the coolant is vapo-

rized and binds heat to itself, cooling the

cabinet. The heat bound to the coolant

goes out via the condenser into the sur-

rounding air space.

In the wine cabinet, ice formed on the

expansion coil melts automatically and

the resulting water is conducted to the

evaporation trough in the compressor

area, from which it evaporates automa-

tically.

Faultless functioning of the cooling

mechanism presupposes that the air

circulation outside and also inside the

appliance is good (drawing below).

The guarantee will become void if above instructions about cooling

mechanism is not conformed.

Functional description

Kitchen worktop

Internal fan

Expansion coil

Condenser

Compressor

Before using the cooling cabinet, clean its

interior parts, following the instructions on

p. 11.

Do not start to use the appliance imme-

diately after transportation or after it has

been kept in a cold place, but let it stand

in its final location for a few hours so

that the oil has time to flow down into

the compressor.

Push the plug on the connecting lead of

the cooling cabinet into the electric

socket.

Main switch ( I )

This switches on the voltage for the app-

liance.

Switch for interior light

Operation of switches

Switches and thermostat

Using the wine cabinet

Note! Do not put foods into the cooling

cabinet before temperature inside the ca-

binet is in the setpoint.

At the factory, the main switch was left in the

OFF- position.

When the main switch is put to the ON

position, then - after about 10 seconds - the

temperature of the cooling cabinet appears

on the display.

The temperature set at the factory is +12°C.

The temperature for the cooling cabinet can

be chosen in the range +8...+18°C to an

accuracy of 1°C.

Normally, the display shows the interior

temperature of upper part of the cooling

cabinet.

Switching on

Switch off the wine cabinet using the main

switch, by pressing the switch to the 0

position.

If the cabinet remains unused during a long

period, then take the plug out of the electric

socket.

Clean and dry the interior parts of the

cabinet and leave the door slightly open.

Switching off

SET

PGR

Interior light switch

Upper button

Lower button

Display

Main switch

Adjusting the temperature

Actual temperature in the cooling cabinet

= display doesn't flash

Set point in the display = display flashes

Factory set point is +12°C

The temperature that has been set can be

brought into view by pressing upper button

of the display for about 2 seconds. The

display will begin to flash, showing the set

temperature. After a while, the flashing will

stop and the set temperature will remain in

force.

Adjusting the temperature

• Press the display button (upper or

lower) until the display begins to flash.

• Using the button (upper button up,

lower button down), select the desired

temperature and leave it visible.

• The selection has now been made,

and no separate confirmation is

needed.

• The display will return to showing the

interior temperature.

The temperature that has been set can be

brought into view by pressing the button

(upper or lower) of the display for about 2

seconds. The display will begin to flash,

showing the set temperature. After a while,

the flashing will stop and the set temperature

will remain in force.

Sounds during operation

Resonance noise may be produced if the

appliance is not completely straight - or if

parts of the pipe system are touching one

another, in which case the pipes can be

bent apart carefully by hand.

Cooling system

When the refrigerant is being pumped

into the piping, a hissing or bubbling

sound is heard.

Compressor

When the refrigerant is being pumped, a

droning or “snoring” noise is heard from

the compressor motor and the pump.

Fan

When the compressor starts up, the fan

inside the cabinet also starts up at the

same time.

This causes a low humming, which is

heard throughout the period when the

compressor is running.

Normal sound of the cooling cabinet

The wine cabinet acquires its coldness

from the compressor operated cooling

system.

For this reason, it is completely normal

that the appliance makes a certain sound.

The sound level can vary. The loudness of

the sound is influenced by, for example,

how the cabinet has been installed in pla-

ce, how it is used, and how old it is.

Cleaning

CLEANING THE WINE CABINET

Stop the mechanism of the wine cabinet

using the main switch, for the period during

which the interior surfaces are being

cleaned.

The cleaning water must not be allowed to

get into the control devices (nor into the

lighting in the glass-doored model).

You can clean all the interior surfaces using

lukewarm water with a little washing-up

liquid added. Scouring agents or solvents

are not suitable for cleaning the cabinet.

Dry the interior and the seal thoroughly.

CLEANING AND SERVICE

NOTE: Stop the mechanism by using the

main switch, and always take the plug out of

the wall socket for the period during which

cleaning or other maintenance work is

being done.

Cleaning the mechanism

Pull the cooling cabinet away from the wall.

Remove dust and other dirt from the

compressor area and from around the

condenser (black grill) at the back of the

appliance. This should be done regularly,

once a year.

The cleaning can be done easily using the

brush attachment of a vacuum cleaner, for

example. Dirt in the compressor area and

on the condenser weakens the functioning

of the mechanism and increases its electricity

consumption.

While the appliance is drawed away from

the wall it would be advisable to check that

the drain pipe is clean. If there is much dirt

in the drain pipe it is possible that water

doesn't drain like it should.

The drain pipe is situated over the

compressor.

Also the evaporation pan is advisable to

clean.

The door is advisable to adjust if it is not

straigth and even.

Stainless steel door frame is coated with

Easy Clean coating. It protects the

surface against dirt. Do not use cleaning

agent for steel surfaces because it

damages the protective coating.

CORRECTING MINOR DISORDERS

All functional disorders do not necessarily

require the help of service personnel. So

check first whether you can eliminate the

disorder with the aid of the following

instructions.

If there is no fault in the appliance, you

yourself will be obliged to pay the costs

arising from any servicing visits, also du-

ring the guarantee period.

If the cooling mechanism does not

work, check that:

• you have followed the advice in the

operating instructions

• the plug is properly in the socket

• the fuse is intact

• the main switch and operating switches

are in the ‘on’ position

• there are no interruptions in electricity

distribution

NOTE! If the temperature of the surroun-

dings becomes unusually high, the inter-

nal protective device of the compressor

may stop the mechanism. Depending on

the conditions, restarting may take ½ - 1

hour.

If the cooling capacity is poor:

• check that the door is tightly closed

• the door may have been opened of-

ten or kept open for too long

• too many goods at a time may have

been put in to cool

• the air circulation outside or inside

may have been hindered

Functional disorders

If the light inside the cabinet does not

work:

• the lamp is broken

-replace the lamp.

Lamp type:

PL TUBE 7W, base G 23

Changing the lamp:

• Stop the mechanism using the ope-

rating switch of the cabinet

• Take the plug out of the wall socket

• Disconnect the plastic lid of interior

light by opening three cross head

screws.

• Change the lamp.

• Connect the plastic lid of interior

light.

• Push the plug into the wall socket.

• Press switch (I) on.

E6 + sound signal = too low tempereture.

Failure comes into view after one hour the

temperature has gone below +2°C.

Acknowledge and stop the sound signal by

pressing the button of the display.

E6 will remain on the display.

Please contact the Festivo-service

organization.

E7 + sound signal = contact fault between

display and adjuster.

Acknowledge and stop the sound signal by

pressing the button of the display.

E7 will remain on the display.

Please contact the Festivo-service orga-

nization.

Look first at page 11, Functional

disorders.

If the above-mentioned functions are in

order, but the appliance does not begin

cooling within about two hours, please contact

the Festivo-service organization.

Error messages

E2 + sound signal = sensor fault.

Acknowledge and stop the sound signal by

pressing the button of the display.

E2 will remain on the display.

Please contact the Festivo-service orga-

nization.

E3 +sound signal = too high temperature.

The error message will appear one hour

after the temperature exceeds +23°C.

Acknowledge and stop the sound signal by

pressing the button of the display.

E3 will remain on the display.

Please contact the Festivo-service orga-

nization.

DISCARDED COLD STORAGE APPLIAN-

CES ARE HAZARDOUS WASTE

By a law amendment that came into force on

1st January 2002, discarded cold storage

appliances are classed in the whole EU

area as hazardous waste.

Disposal of the appliance

Take care not to damage the refrigerant

pipes of the winecabinet before or during

transport to an authorised collection depot.

So refrigerant in the pipework and oil in the

compressor will be contained, and will not

leak out into the environment.

Suomen Kotikylmiö Oy, Ravitie 3, 15860 Hollola, FINLAND

Tel. +358 (0)3 553 8600, fax +358 (0)3 553 8668

www.festivo.fi

Festivo 50 VL Instructions For Installation And Use Manual

Brand: Festivo

Model: 50 VL

Category: Wine coolers

Type: Instructions For Installation And Use Manual

Download PDF

report

Festivo 50 VL Instructions For Installation And Use Manual

Festivo 50 VL Instructions For Installation And Use Manual

Other documents