BDI Sigma 6902 User manual

Type
User manual
Designed by BDI Studio.
These distinctive product configurations are protected by US and international patents, trade dress, and/or
copyright laws. Sigma & BDI are trademarks of Becker Designed, Inc. All rights reserved. ©2019, BDI
Made in Turkey. 02.18.2019
T1 4mm Hex Wrench x1
Hardware:
C2 Frame x 1
C3 Leg x 1
C1 Glass Panel x 1
H1 M6 x 15mm Screw
x 11
Product Registration
Registering your new BDI product allows us to send you important
product updates, service information and helpful hints related to your
BDI products. Register today and you will be entered to win free a
BINK table from BDI. www.bdiusa.com/product-registration/
Placement and Maintenance
Sigma
Office furniture is designed for indoor use on level floors.
Clean glass with glass cleaner, and other surfaces with a moist cloth.
Your Sigma
Office furniture is engineered for easy assembly.
Carefully follow this procedure to prevent any damage.
Do not use power tools for assembly of this product.
Step 1
Unpack and identify the parts listed below. The assembly workspace
should be a non-marring surface such as carpet. For missing hardware
pieces, please contact BDI Customer Service at:
For all other concerns, please contact your BDI retailer.
bdiusa.com
customerservice@bdiusa.com
SIGMA
TM
6902
RETURN
bdiusa.com
customerservice@bdiusa.com
SIGMA 6902
RETURN
2
Step 2 - Position the frame C2 upside down (end plate facing up). Position the top of the leg C3 over the
matching 4 threaded inserts on the cross bar. Attach the leg to the cross bar using screws H1 and hex
wrench T1.
H1
H1 x 4
T1
End plate up
cross bar
C2
C3
bdiusa.com
customerservice@bdiusa.com
SIGMA 6902
RETURN
3
Step 3 - Determine of you want the return on the left or right side of the desk. Find the 3 threaded insert below
the front edge (left or right). Thread a screw H1 in half way into the middle insert. With help from another
person, position the return so that the notch in the end plate goes around the middle screw. Tighten the middle
screw with the hex wrench.
1 screw H1 half way
into middle insert
(left hand side)
1 screw H1 half way
into middle insert
(right hand side)
Choose
left hand or
right hand
notch in end
plate
2 Person Ta sk
H1
C2
or
bdiusa.com
customerservice@bdiusa.com
SIGMA 6902
RETURN
4
Step 4 - Insert screws H1 into the outer holes of the end plate and tighten all screws with hex wrench T1.
H1 x 2
T1
bdiusa.com
customerservice@bdiusa.com
SIGMA 6902
RETURN
5
Step 5 - With the help of another person, position the glass panel C1 over the frame C2 with the larger glass
overhang in the front. Align all edges (with glass inset 1/16” or 1.5mm). Attach the glass panel C1 using
screws H1 going though the 4 corner plates and tighten with hex wrench.
Step 6 - Adjust the leveler at the bottom of Sigma Return’s leg if necessary.
2 Person Ta sk
H1 x 4
T1
corner plate
C2
C1
leveler
large overhang
1.5 mm
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

BDI Sigma 6902 User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI