Minka Group 2922-77-L User manual

Type
User manual

Minka Group 2922-77-L is a dimmable LED wall-mounted fixture. This fixture is suitable for both indoor and outdoor use and can be mounted on a wall or ceiling. The fixture is made of metal and has a white finish. It uses a single LED bulb, which is included. The fixture is easy to install and comes with all the necessary hardware.

Capabilities: The Minka Group 2922-77-L fixture is dimmable, allowing you to adjust the brightness of the light to suit your needs. The fixture is also compatible with both CFL and LED bulbs, giving you the flexibility to choose the type of bulb that best suits your needs. The fixture is designed for both indoor and outdoor use, making it a versatile option for a variety of applications.

Minka Group 2922-77-L is a dimmable LED wall-mounted fixture. This fixture is suitable for both indoor and outdoor use and can be mounted on a wall or ceiling. The fixture is made of metal and has a white finish. It uses a single LED bulb, which is included. The fixture is easy to install and comes with all the necessary hardware.

Capabilities: The Minka Group 2922-77-L fixture is dimmable, allowing you to adjust the brightness of the light to suit your needs. The fixture is also compatible with both CFL and LED bulbs, giving you the flexibility to choose the type of bulb that best suits your needs. The fixture is designed for both indoor and outdoor use, making it a versatile option for a variety of applications.

INSTALLATION INSTRUCTIONS
FOR 2922-77-L
For LED Wall Mount Fixture
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AV E R T I S S E M E NT !C O U P E R L E CO U R AN T AU N I V E AU D E S F U S I B L E S O U D O DI SJ O N C T E U R .
Fig.1F
Fig. 2
Fig.3
IMPORTANT: Fixture should be installed by a
qualified electrician to ensure proper wiring and
installation.
Dimmable with C-L (CFL & LED) type and
Incandescent/Halogen type dimmers
II 800
MOUNTING THE FIXTURE (Fig. 1)
1. Shut off power at the fuse box or circuit breaker box. If necessary
remove the existing fixture and its mounting hardware.
2. Carefully remove the new fixture from the carton and check that
all parts are included as shown in the illustration.
3. Position mounting plate (A) on the wall, and mark the location of
the two drywall anchors (G). Pre-drill the holes for the drywall
anchors (G) and insert the drywall anchors (G) into the wall.
4. Attach the mounting plate (A) to the junction box using junction
box screws (B) (Size: 8-32*1/2’’L). The side of the mounting plate
marked “GND” must face out.
5. Place the wood screws (F) through the holes of the mounting
plate (A) and into the drywall anchors (G) to secure the mounting
plate (A) to the wall.
CONNECTION THE WIRES (Fig. 2)
6. At this point, connect the electrical wires as shown in Fig.2,
making sure that all wire connectors are secured. If your outlet
has a ground wire (green or bare copper), connect the fixture's
ground Wire to it. Otherwise, connect the fixture's ground wire
directly to the mounting plate using the green screw provided.
After the wires are connected, tuck them carefully into the junction
box.
FINISHING THE INSTALLATION (Fig. 1)
7. Align Fixture (E) to mounting plate (A) and secure with screws
(D).
8. Place glass shade (L) inside the fixture (E), and secure with screw
(Q) steel washer (P) and plastic washer (O).
Your installation is now complete. Return power to the junction box and
test the fixture.
CAUTION /ATTENTION: When handling the fixture, do not apply
pressure to the LEDs. Hold the fixture by the base or fixture body
(E) only.
Replacing LED module (Fig.3)
The LED module can be replaced by a qualified electrician without
cutting the wires and without damaging the decorative element to
which the fixture is attached. See installation steps for more details
(Fig 3.)
Warning: Turn off power at the fuse box or circuit breaker
before replacing LED module.
a. To remove the fixture from the wall: loosen screws (D) and
remove the wire connectors. Then place the fixture on a clear flat
surface.
b. Loosen screw(Q) to remove the glass shade (L)
c. Loosen screws (R) to remove end caps (H) and glass shade (K).
d. Loosen screws (J), screws (M), wire fastener (N) and then
carefully remove LED module (I).
e. Reverse steps a-c for installing the new LED module.
Note: The LED module should be provided by a specified supplier.
  • Page 1 1

Minka Group 2922-77-L User manual

Type
User manual

Minka Group 2922-77-L is a dimmable LED wall-mounted fixture. This fixture is suitable for both indoor and outdoor use and can be mounted on a wall or ceiling. The fixture is made of metal and has a white finish. It uses a single LED bulb, which is included. The fixture is easy to install and comes with all the necessary hardware.

Capabilities: The Minka Group 2922-77-L fixture is dimmable, allowing you to adjust the brightness of the light to suit your needs. The fixture is also compatible with both CFL and LED bulbs, giving you the flexibility to choose the type of bulb that best suits your needs. The fixture is designed for both indoor and outdoor use, making it a versatile option for a variety of applications.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI