Minka Group 2922-77-L User manual

Brand: Minka Group

Model: 2922-77-L

Type: User manual

Minka Group 2922-77-L is a dimmable LED wall-mounted fixture. This fixture is suitable for both indoor and outdoor use and can be mounted on a wall or ceiling. The fixture is made of metal and has a white finish. It uses a single LED bulb, which is included. The fixture is easy to install and comes with all the necessary hardware.

Capabilities: The Minka Group 2922-77-L fixture is dimmable, allowing you to adjust the brightness of the light to suit your needs. The fixture is also compatible with both CFL and LED bulbs, giving you the flexibility to choose the type of bulb that best suits your needs. The fixture is designed for both indoor and outdoor use, making it a versatile option for a variety of applications.

INSTALLATION INSTRUCTIONS

FOR 2922-77-L

For LED Wall Mount Fixture

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.

AV E R T I S S E M E NT !C O U P E R L E CO U R AN T AU N I V E AU D E S F U S I B L E S O U D O DI SJ O N C T E U R .

Fig.1F

Fig. 2

Fig.3

IMPORTANT: Fixture should be installed by a

qualified electrician to ensure proper wiring and

installation.

Dimmable with C-L (CFL & LED) type and

Incandescent/Halogen type dimmers

II 800

MOUNTING THE FIXTURE (Fig. 1)

1. Shut off power at the fuse box or circuit breaker box. If necessary

remove the existing fixture and its mounting hardware.

2. Carefully remove the new fixture from the carton and check that

all parts are included as shown in the illustration.

3. Position mounting plate (A) on the wall, and mark the location of

the two drywall anchors (G). Pre-drill the holes for the drywall

anchors (G) and insert the drywall anchors (G) into the wall.

4. Attach the mounting plate (A) to the junction box using junction

box screws (B) (Size: 8-32*1/2’’L). The side of the mounting plate

marked “GND” must face out.

5. Place the wood screws (F) through the holes of the mounting

plate (A) and into the drywall anchors (G) to secure the mounting

plate (A) to the wall.

CONNECTION THE WIRES (Fig. 2)

6. At this point, connect the electrical wires as shown in Fig.2,

making sure that all wire connectors are secured. If your outlet

has a ground wire (green or bare copper), connect the fixture's

ground Wire to it. Otherwise, connect the fixture's ground wire

directly to the mounting plate using the green screw provided.

After the wires are connected, tuck them carefully into the junction

box.

FINISHING THE INSTALLATION (Fig. 1)

7. Align Fixture (E) to mounting plate (A) and secure with screws

(D).

8. Place glass shade (L) inside the fixture (E), and secure with screw

(Q) steel washer (P) and plastic washer (O).

Your installation is now complete. Return power to the junction box and

test the fixture.

CAUTION /ATTENTION: When handling the fixture, do not apply

pressure to the LEDs. Hold the fixture by the base or fixture body

(E) only.

Replacing LED module (Fig.3)

The LED module can be replaced by a qualified electrician without

cutting the wires and without damaging the decorative element to

which the fixture is attached. See installation steps for more details

(Fig 3.)

Warning: Turn off power at the fuse box or circuit breaker

before replacing LED module.

a. To remove the fixture from the wall: loosen screws (D) and

remove the wire connectors. Then place the fixture on a clear flat

surface.

b. Loosen screw(Q) to remove the glass shade (L)

c. Loosen screws (R) to remove end caps (H) and glass shade (K).

d. Loosen screws (J), screws (M), wire fastener (N) and then

carefully remove LED module (I).

e. Reverse steps a-c for installing the new LED module.

Note: The LED module should be provided by a specified supplier.

Minka Group 2922-77-L User manual

Minka Group 2922-77-L User manual

Minka Group 2922-77-L User manual

Related papers

Other documents