Outback HUB 10.3 Quick start guide

Brand: Outback

Model: HUB 10.3

Type: Quick start guide

#10 x ½” Screws x 2

Quick Start Guide

900-0154-01-00 Rev A.vsd\2013-03-13

HUB 10.3

HUB10.3 HUB Wiring Cover

Cable, CAT5e, 3' (1 m) x 2

Cable, CAT5e, 6' (2 m) x 3

Parts List

Cable, CAT5e, 10' (3 m) x 4

Contact Technical Support:

Telephone: +1.360.618.4363

Email: [email protected]

Website: www.outbackpower.com

IMPORTANT:

Not intended for use with

life support equipment.

OutBack Power, the OutBack Power Logo, and FLEXgrid

are trademarks owned and used by OutBack Power

Technologies, Inc. The ALPHA logo and the phrase

“member of the Alpha Group” are trademarks owned and

used by Alpha Technologies. These trademarks may be

registered in the United States and other countries.

Stacking

HUB 10.3

900-0154-01-00 Rev A.vsd\2013-03-13

Jumper position

identified by MATE3 on

power-up:

3-Phase/Split

Single-Phase



Changing Jumpers

1. 2.

Used for classic

series, OutBack

series, and parallel

stacking. This is

the factory-installed

initial position.

Used for Subphase

Master stacking (both

three-phase and series

configurations).

4a.

Single-phase

(all jumpers)

4b.

3-Phase/Split

(all jumpers)



1" recommended

Mounting

NOTE: This option requires MATE3

firmware revision 002.013.000 or higher.

Master A

Master C

Slave

MATE

Three-Phase Stack (Subphase Master)

Up to 9 inverters (ports 1 to 9); 1 other device (port 10); MATE3 only

Ports 1, 4, and 7 are required regardless of the number of slaves; also, the number of slaves should be even

Jumpers must be in

“3-Phase/Split” position

Rev 002.013.000

or higher

Port 1

Stack Mode Master

Port 2

Stack Mode Slave

OB Slave L1

Port 4

Stack Mode B Phase Master

3p Classic B

Port 7

Stack Mode C Phase Master

3p Classic C

Also ports 3, 5, 6, 8, and 9

MATE

Port 1

Stack Mode Master

Port 2

Stack Mode 3phase OB Slave A

3phase OB Slave B

3phase OB Slave C

Three-Phase Stack

Up to 9 inverters; 1 other device (MATE or MATE3)

10987654321

Models

Ports 2 to 10 can be assigned any

3phase OB Slave stack mode;

no more than 3 inverters per mode

Jumpers must be in

“Single-phase” position

GTFX (E Series)

GVFX (E Series)

Master B

Slave

Back of HUB 10.3

10.63" (27 cm)

6.18"

(15.7 cm)

1.27" (3.2 cm)

4.23"

(10.7 cm)

9.24" (23.5 cm)

Dimensions

GS7048E

GFX

GFX (E Series)

Models

Single-phase

inverters:

Three-phase output

PHASE A

PHASE B

PHASE C

Shutter Bushing x 2

Snap Bushing x 2

Single-phase inverters:

Three-phase output

Stacking

HUB 10.3

Stacking

10987654321

MATE

FX / VFX (includes

J, M, N Series)

Models

Port 1

Stack Mode Master or 1-2phase Master

Port 2

Stack Mode OB Slave L1

OB Slave L2

Series Stack (OutBack)

Up to 10 inverters or other devices (MATE or MATE3)

Requires balancing transformer

HUB 10.3

Jumpers must be in

“Single-phase” position

900-0154-01-00 Rev A.vsd\2013-03-13

10987654321

MATE

FX / VFX (includes

J, M, N Series)

GTFX

GVFX

GTFX (LA Series)

GVFX (LA Series)

Models

Port 1

Stack Mode Master or 1-2phase Master

Port 2

Stack Mode Classic Slave

Series Stack (Classic)

2 inverters; up to 8 other devices (MATE or MATE3)

GFX

Jumpers must be in

“Single-phase” position

10 987 654 321

MATE

GFX

Models

Series Stack (Subphase Master)

Up to 8 inverters (ports 1 to 4, 7 to 10); 2 other devices (ports 5, 6); MATE or MATE3

No balancing transformer required

Improves control of individual phase voltages and outputs

Ports 2 to 4 are L1 slaves; ports 8 to 10 are L2 slaves despite the screen selection (OB Slave L1); equal inverters should be on L1 and L2

Port 7 is the L2 subphase master despite the screen selection (Classic Slave); this port is required regardless of number of slaves

Jumpers must be in

“3-Phase/Split” position

Port 1

Stack Mode Master

Port 2

Stack Mode OB Slave L1

Also ports 3, 4, 8, 9, and 10

Port 7

Stack Mode Classic Slave

MATE

Port 1

Stack Mode Master or 1-2phase Master

Port 2

Stack Mode Slave or OB Slave L1

Parallel Stack

Up to 10 inverters or other devices (MATE or MATE3 where appropriate)

10987654321

GS8048

Models

FX / VFX (all series,

including E, J, M, N,

and W)

Also port 3, etc.

Jumpers must be in

“Single-phase” position

GS7048E

GFX

GFX (E Series)

(with

FX-class

inverter)

Single-phase

inverters:

Single-phase output

Split-phase

inverters:

Split-phase output

GTFX (E Series)

GVFX (E Series)

Single-phase

inverters:

Split-phase output

Single-phase

inverters:

Split-phase output

Ports 2 to 10 can be assigned to either

OB Slave L1 or OB Slave L2;

equal numbers of inverters should be

assigned to each side

Single-phase

inverters:

Split-phase output

Outback HUB 10.3 Quick start guide

Outback HUB 10.3 Quick start guide

Outback HUB 10.3 Quick start guide

Related papers

Other documents