Sharper Image Night Light Toilet Seat Owner's manual

Brand: Sharper Image

Model: Night Light Toilet Seat

Type: Owner's manual

This manual is also suitable for

Sound Activated Nightlight Toilet Seat

Sharper Image Night Light Toilet Seat is a convenient and innovative toilet seat that combines practicality with a unique night light feature. It utilizes sound activation to automatically illuminate the toilet bowl area when someone enters the bathroom, providing a soft blue glow that aids visibility in low-light conditions. The slow-close hinge prevents slamming and ensures a quiet operation, while the quick-release hinges allow for easy removal of the seat for cleaning and maintenance.

ONE YEAR LIMITED WARRANTY

Ginsey Home Solutions sells its products with the intent that they are free

of defects in manufacture and workmanship for a period of one year from

the date of original purchase. Ginsey Home Solutions warrants that its

products will be free of defects in material and workmanship under

normal use and service.

For warranty service call:

Ginsey Home Solutions

2078 Center Square Road

Swedesboro, NJ 08085

1-800-257-7844

service@ginsey.com

GETTING STARTED

Battery Installation

1) The nightlight operates on 2 x AAA (LR03) batteries (not

included).

2) Lay the toilet seat on a ﬂat surface with the lid and ring in the

open position as shown.

Remove the 2 Phillips head screws from the LED housing.

Remove and open the LED housing.

Install 2 x AAA batteries with polarity (+/-) as shown in FIGURE 1.

Make sure the silicone water seal is seated in place, close the

LED housing, place back into the toilet lid and tighten screws.

Do not over tighten.

TOILET SEAT INSTALLATION

Read all instructions very carefully BEFORE installation.

1) Remove old toilet seat and mounting

hardware from toilet bowl.

2) Remove new mounting hardware

from parts bag. Insert the 2

Plastic Mounting Sleeves (A) into

the mounting holes on your toilet

bowl by squeezing the 2 plastic

arms together with your thumb

and foreﬁnger.

a) If you are having diculty

getting the plastic sleeve into the

hole, insert the plastic sleeve into

the hole at an angle and rock it

back and forth as you push it

down.

b) Remove the Bolt (D) from the

plastic sleeve.

c) Push the sleeve all the way

into the hole until the ﬂange is

ﬂush with the top of the bowl.

d) If the ﬁt is tight, use the handle

of the screwdriver to forcibly

push the sleeve down until it is

completely ﬂush with the bowl.

3) Insert the Rubber

Gasket (B) into the

plastic bottom of

each Hinge Pin

Mount (C).

4) Place the Hinge Pin

Mount (C) over the

Plastic Mounting

Sleeve (A) in the

position shown

below.

5) Insert Bolt (D) into

Plastic Hinge

Mounting Sleeve (A)

and tighten to a

snug ﬁt only. DO

NOT FULLY

TIGHTEN THE

BOLTS YET. The

metal pins need to

be equally spaced

4 ¾” apart as

shown in Figure 5.

6) To check the spacing,

place the toilet seat

upside down on the

bowl so that the

mounting holes in the

seat line up with the

metal pins.

7) If the metal pins do not

line up with the holes in

the toilet seat, loosen

Bolt (D) and twist the

Hinge Pin Mount (C)

until they line up with

the holes. Retighten the

Bolts (D) until they are

snug, but do not fully

tightened yet.

8) Gently place the toilet

seat over the Hinge Pin

Mounts (C). Allow the

toilet seat to gently

close.

9) Check the alignment of

the toilet seat with the

toilet bowl. If the seat

is too far forward or

too far back or too far

left/right, remove the

seat and readjust the

Hinge Pin Mounts (C).

You can adjust the seat

forward or back using

the slot in the Hinge

Pin Mounts (C).

10) Once the toilet seat is

aligned with the bowl,

gently remove the

seat and fully tighten

the bolts securely

with a Phillips head

screw driver.

11) The plastic sleeves

should look as shown

in image.

14)

To remove the seat for cleaning,

simply press the gray button

and pull up on the seat. Once

cleaning is complete, align the

hinge holes to the hinge pins

and press down ﬁrmly to secure

the seat to the toilet bowl.

13) Now click the toilet seat onto the

Hinge Pin Mounts (C) and check

for proper function and alignment

with the toilet bowl.

12) Place the Protective

Caps (E) over the

Hinge Pin Mounts (C)

and push down

securely.

NIGHTLIGHT FUNCTION

The LED will only turn ON when it is dark or night time. The LED will turn ON

when it detects a sound of someone entering the bathroom (Approximately 65

dB). It provides a soft blue glow that illuminates the toilet lid and ring and is

easy on your eyes in the middle of the night. The LED will automatically shut

o after 2 minutes. The batteries will last about 6 months.

HAVING TROUBLE INSTALLING YOUR SEAT?

Check out our instructional video for the Sharper Image Sound Activated

Nightlight Toilet Seat at https://youtu.be/uP9nEbiFam0

QUICK RELEASE HINGES

The seat has a quick release feature to help you remove it for easy

cleaning. To remove the seat, simply press the gray button on the back of

the seat and pull up the seat. To put the seat back on, reverse the steps

above. The toilet seat will snap back onto the hinges.

CLEANING AND MAINTENANCE

• Clean the toilet seat as you normally would with bathroom

cleaner and water. Dry with soft cloth.

• The LED housing is water resistant. DO NOT SUBMERGE THE

LED HOUSING.

PRESS

CLEAN

PRESS TO

SECURE

PRESS TO

SECURE

sound activated

with slow-close hinge

NIGHTLIGHT TOILET SEAT

ROUND

Plastic Mounting

Sleeve

Rubber

Gasket

Hinge Pin

Mount

Protective CapBolt

1 YEAR LIMITED WARRANTY

• Read all instructions carefully before use.

• Carefully remove all contents from the packaging and

inspect the product to make sure all components have

been received.

• Tools Required: Phillips head screwdriver

Thank you for purchasing the Sharper Image®

Nightlight Toilet

Seat. LED technology softly lights your way to the bathroom at

night. The Sound Activated Auto On and O features allows the

LED to operate only when you need it. The slow-close hinge

helps prevent the lid and ring from slamming down and waking

the house, and the quick release hinge makes cleaning a breeze.

LED Light Module

Battery Compartment

2x AAA batteries are required

Slow Close/Quick Release Hinge

Model No: 01271

CAUTION:

• Do not mix old and new batteries or batteries of dierent

types: alkaline, standard (carbon-zinc) or rechargeable

(nickel-cadmium).

• Insert batteries with correct polarity as indicated inside the

battery compartment.

• Remove batteries during long periods of non-use.

• Always remove exhausted batteries from this product.

Dispose of batteries safely.

BATTERY INSERTION

FIGURE 1.

Made in China

For more information on

Sharper Image products,

please visit: www.sharperimage.com

name and logo are registered trademarks.

marketed and distributed under license

by Ginsey Home Solutions, Swedesboro, NJ 08085.

2c.

2d.

13.

14.

2a.

9a.

11.

9b.

Customer Service is available

8:30am – 5:00pm (EST)

Monday – Friday

21.25 IN.

11 IN.

100% Scale

1-Color Process - Black

FRONT

FOLD

Insert the 2 Plastic

Mounting Sleeves (A) into

the mounting holes on

your toilet bowl by

squeezing the 2 plastic

arms together with your

thumb and foreﬁnger.

Remove the Bolt (D) from

the plastic sleeve.

Push the sleeve all the

way into the hole until the

ﬂange is ﬂush with the top

of the bowl.

Insert the Rubber Gasket

(B) into the plastic bottom of

each Hinge Pin Mount (C).

Place the Hinge Pin

Mount (C) over the Plastic

Mounting Sleeve (A) in the

position shown below.

Insert Bolt (D) into Plastic

Hinge Mounting Sleeve (A)

and tighten to a snug ﬁt

only. DO NOT FULLY

TIGHTEN THE BOLTS YET.

The metal pins need to be

equally spaced 6 ¾” apart

as shown.

If the metal pins do not line

up with the holes in the toilet

seat, loosen Bolt (D) and

twist the Hinge Pin Mount

holes. Retighten the Bolts

(D) until they are snug, but

do not fully tightened yet.

Gently place the toilet seat

over the Hinge Pin Mounts

(C). Allow the toilet seat to

gently close.

Check the alignment of the

toilet seat with the toilet

bowl. If the seat is too far

forward or too far back or too

far left/right, remove the seat

and readjust the Hinge Pin

Mounts (C). You can adjust

the seat forward or back

using the slot in the Hinge

Pin Mounts (C).

Once the toilet seat is aligned

with the bowl, gently remove

the seat and fully tighten the

bolts securely with a Phillips

head screw driver.

Now click the toilet seat

onto the Hinge Pin Mounts

function and alignment with

the toilet bowl.

Place the Protective Caps (E)

over the Hinge Pin Mounts

sound activated

with slow-close hinge

NIGHTLIGHT TOILET SEAT

ROUND

Plastic Mounting

Sleeve

Rubber

Gasket

Hinge Pin

Mount

Protective CapBolt

Made in China

For more information on

Sharper Image products,

please visit: www.sharperimage.com

name and logo are registered trademarks.

marketed and distributed under license

by Ginsey Home Solutions, Swedesboro, NJ 08085.

QUICK START GUIDE

STEP 1.

STEP 2.

STEP 3.

STEP 4.

STEP 5.

STEP 6.

SCAN FOR VIDEO

Read all instructions very carefully BEFORE installation.

HAVING TROUBLE INSTALLING YOUR SEAT?

Check out our instructional video for the Sharper Image Sound Activated

Nightlight Toilet Seat at https://youtu.be/uP9nEbiFam0

11 IN.

8.5 IN.

100% Scale

1-Color Process - Black

FRONT

FOLD

Sharper Image Night Light Toilet Seat Owner's manual

Brand: Sharper Image

Model: Night Light Toilet Seat

Type: Owner's manual

This manual is also suitable for

Sound Activated Nightlight Toilet Seat

Download PDF

report

Sharper Image Night Light Toilet Seat Owner's manual

This manual is also suitable for

Sharper Image Night Light Toilet Seat Owner's manual

Related papers

Other documents