2. V-ZUG
  3. 002
002

V-ZUG 002, 488, 489 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the V-ZUG 002 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • Who should install the appliance?
    What accessories are included with the installation?
    How much space is needed beneath the appliance for ventilation?
    What is the minimum depth of the work surface required to place an oven underneath the appliance?
    What type of adhesive is used for the steel angle?
    What is the minimum air gap required over the entire cabinet element width?
    Can a protective plate be fitted above the drawer for ventilation?
    What is the minimum space required for the ventilation below the worktop?
Installation instructions
Induction glass ceramic hob
Frameless, for flush installation
J488.123-2
20.1.09 ITH
1
These installation instructions apply to the models: 488 (GK46TIF), 489 (GK46TIVF), 002 (GK46TIASF)
Identification plate
The identification plate is next to the connection plate.
A Affix the second identification plate (enclosed) in an accessible position behind the front
of the fitted cabinet beneath the appliance.
The appliance should be installed by qualified personnel only. Each step must be carried out and checked in full in the order
specified.
Validity
General notes
If fitting in flammable material, the guidelines and standards for low voltage installations and for the fire protection must be strict-
ly observed.
Installation accessories included
Designation Article no.
Cementing-in instructions J004.130
Sealing strip set H6.2142
Accessories
Designation Article no.
Steel angle set
Installation dimension 60
Installation dimension 80
H6.2084
H6.2085
Ventilation protection plate set
For niche width 550–600 mm
For niche width 825–900 mm
H6.2122
H6.2123
Instant adhesive for the installation of the steel angle
Permabond F246, incl. Activator, 50 ml tube. From Silitech AG, 3008 Bern.
B11.502
Cement set
Complete with cleaning agent, primer type 1105, cartridge with silicon adhesive, black with nozzle. Suit-
able for all absorbent worktop materials (wood and natural stones such as marble and granite).
86.3928.85
Special primer type 107
Suitable for non-absorbent worktop materials (not suitable for polyethylene, polypropylene or Teflon).
45.2771.76
Connection plate
Identification plate
Installation instructions
Induction glass ceramic hob
Frameless, for flush installation
J488.123-2
20.1.09 ITH
2
A Information on the necessary mains voltage, type of current and fuse protection is to be obtained from the identification plate.
A The appliance is equipped with a mains cable that should be connected to a distribution box by the customer.
A If an oven is installed under the appliance, we recommend placing the distribution box behind the base. A cut-out can be made in
the rear wall for the cables.
Error message U400
Indications
䡲 The worktop must be flat.
䡲 In order to guarantee good ventilation, a space of at least 2 cm height is necessary beneath the appliance.
䡲 If the depth of the work surface is ≥30 mm, you can place an oven with 762 mm height directly underneath the appliance, exception:
M-SL[P].
䡲 It is to possible install an oven in the short mounting forms 55-600, 60-600, 55-381 or 60-381 beneath the appliance if you use a
ventilation grille set (oven accessories).
Electrical connections
Electrical connections must be carried out by trained electricians in accordance with the guidelines and standards for low volt-
age installations and the specifications of the local electricity supply companies.
A plug-in appliance may only be connected to a socket outlet with earthing contact, installed according to specifications. A
mains isolating device with 3 mm contact opening should be provided in the house wiring system. Switches, plug and socket
devices, circuit breakers and fusible cut-outs which are accessible after installation and which have all-poles switching are per-
missible as isolating devices. Effective earthing and separately installed neutral and earth conductors ensure safe and fault-
free operation. After installation, live parts and cables with basic insulation must not be accessible. Old installations should al-
ways be checked.
Incorrect connection:
A pole conductor was connected to the connecting terminal for neutral conductors.
Quickly disconnect the appliance from the mains!
Installation
600/550
900
Installation pipe
Distribution box
Clamp
400 V 2N~
230 V~
AUS / NZ
PE/ green/yellow
N blue
L1 brown
L2 black
PE/ green/yellow
N blue
L1 brown
Installation instructions
Induction glass ceramic hob
Frameless, for flush installation
J488.123-2
20.1.09 ITH
3
Installing
1. Create the installation cut-out accurately.
– The mounting surface can be recessed by installing wood or stone bars or produced using the steel angle set (see
«Accessories»).
2. Prepare the cut-out and the appliance according to the information in the accompanying cementing-in instructions.
3. Carefully cement the appliance in place and allow the silicon cement joints to dry for at least 24 hours.
4. Where necessary establish the mains supply connection before inserting the appliance.
Cool air supply if installed over a drawer or cabinet
In order to guarantee good ventilation, there needs to be a space of at least 2 cm height beneath the appliance.
With a protective plate beneath the ventilator
If necessary, a protective plate (see «Accessories») can be fitted above the drawer.
The layout of the cooking zones on the integrated hob may differ from the illustrated hob!
GK46TIF GK46TIVF, GK46TIASF
Access to the appliance from below must be guaranteed over the entire cut-out surface. For servicing, the induction gen-
erator with the mounting plate can be removed from below. The covers to prevent accidental contact with live parts must
be removable by unscrewing from underneath.
600/550
900
480
550
740
480
743 ±1
Z
483 ±1
553 ±1
600
min. 55
min. 55
min. 30
600/550
900
600
min. 30
483 ±1
min. 55
min. 55
Z
(536/726)
(466)
R14
R0–5
54.6
For symmetrical fitting,
it is not necessary to
cut out the side walls.
Detail Z
Steel angle bonded or screw mounted
(for adhesive see «Accessories»)
8.5 ±0.5
8.5 ±0.5
8.5
8.5
0
-1
0
-0.5
54.6
127
1/6
3
min. 5
min. 15
min. 245min. 240max. 75
ø 75
min. 57
====
min. 30
600/550
900
Centre of fan
Drawer
min. 72.5
Air gap over the entire cabinet element width
min. 25 cm²
Necessary space for the ventilation
below the worktop required
min. 5
==
~10
(17.9)
min. 72.5
min. 54.6
15
Middle of angle
Drawer
Centre of fan
Warning:
Do not place mains cable in the
area of the protective plate
Air gap over the entire cabinet element width
min. 25 cm²
/