Crestron TS-1542 User guide

Type
User guide

This manual is also suitable for

TS-1542/TS-1542-C
15.6 in. HD Touch Screens
Supplemental Guide
Crestron Electronics, Inc.
Original Instructions
The U.S. English version of this document is the original instructions. All other languages are a translation of the original
instructions.
Crestron product development software is licensed to Crestron dealers and Crestron Service Providers (CSPs) under a
limited non-exclusive, non-transferable Software Development Tools License Agreement. Crestron product operating system
software is licensed to Crestron dealers, CSPs, and end-users under a separate End-User License Agreement. Both of these
Agreements can be found on the Crestron website at www.crestron.com/legal/software_license_agreement.
The warranty for Crestron products can be found at www.crestron.com/legal/sales-terms-conditions-warranties.
The specific patents that cover Crestron products are listed at www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, visit
www.crestron.com/legal/open-source-software.
Crestron, the Crestron logo, Crestron AirBoard, Crestron Pyng, Crestron Toolbox, Crestron XiO Cloud, DigitalMedia, DM,
PinPoint, Rava, and Smart Graphics are either trademarks or registered trademarks of Crestron Electronics, Inc. in the
United States and/or other countries. Active Directory is a trademark or a registered trademark of Microsoft Corporation in
the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this
document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary
interest in the marks and names of others. Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2019 Crestron Electronics, Inc.
Supplemental GuideDOC. 7824C Contents i
Contents
Introduction ................................................................................................................................... 1
Product Features ......................................................................................................................... 2
Access the Setup Screens .......................................................................................................... 4
Configure the Device .................................................................................................................. 5
Ethernet Setup ........................................................................................................................................... 5
IP Table Setup ............................................................................................................................................. 7
Audio Setup ............................................................................................................................................... 10
Display Setup ............................................................................................................................................. 11
Standby Timeout ...................................................................................................................................... 12
Diagnostics ................................................................................................................................................ 14
Test Patterns ..................................................................................................................................... 15
Touch Test ........................................................................................................................................... 15
Mic Test ............................................................................................................................................... 16
LAN Test .............................................................................................................................................. 17
Rava Test ............................................................................................................................................ 18
RTSP Test ............................................................................................................................................ 19
DM Preview (TS-1542-C Only) ....................................................................................................... 20
About .......................................................................................................................................................... 21
Configuration via Web Interface ........................................................................................... 22
Status ......................................................................................................................................................... 23
General ................................................................................................................................................ 23
Network ............................................................................................................................................... 24
Control System Connections .......................................................................................................... 25
DM In (TS-1542-C Only) .......................................................................................................................... 26
General Settings ................................................................................................................................ 26
Input Signal......................................................................................................................................... 26
Network...................................................................................................................................................... 27
Network Setting ................................................................................................................................ 27
802.1x Configuration ........................................................................................................................ 29
Device ......................................................................................................................................................... 32
Display ................................................................................................................................................. 33
Device Management ......................................................................................................................... 34
Auto Update ....................................................................................................................................... 37
Control System .................................................................................................................................. 38
Configure Date/Time ....................................................................................................................... 39
Authentication Management ........................................................................................................ 40
Connect to Crestron XiO Cloud Service ............................................................................... 48
Claim a Single Device ............................................................................................................................. 48
Claim Multiple Devices ............................................................................................................................ 49
Supplemental GuideDOC. 7824C TS-1542/TS-1542-C: 15.6 in. HD Touch Screens 1
TS-1542/TS-1542-C: 15.6 in. HD Touch
Screens
Introduction
The Crestron® TS-1542 and TS-1542-C are touch screens with a 15.6 in. HD display and a
built-in high-performance digital graphics engine. The TS-1542 and TS-1542-C feature
Smart Graphics® technology, dual-window HD streaming video display, annotation, voice
recognition, web browsing, and a Rava® SIP intercom.
NOTE: The TS-1542 and the TS-1542-C are functionally similar. For simplicity within this
guide, the term "touch screen" is used except where noted.
For more information on the TS-1542 and TS-1542-C, refer to the TS-1542/TS-1542-C
Quick Start (Doc. 7822) at www.crestron.com/manuals
.
2 TS-1542/TS-1542-C: 15.6 in. HD Touch Screens Supplemental Guide DOC. 7824C
Product Features
Refer to the following chart to determine the product features that are available on the
TS-1542 and TS-1542-C touch screens.
TS-1542/TS-1542-C Feature Chart
FEATURE CLASS FEATURE TS-1542 TS-1542-C
General
Size 15 in.
15 in.
Screen resolution 1920 x 1080 1920 x 1080
HDMI® input N/A N/A
DigitalMedia™ input N/A Up to 4K@30Hz 4:4:4
HDMI output N/A N/A
RS-232 N/A
N/A
IR N/A N/A
CEC N/A N/A
Audio out LPCM, 2 channel LPCM, 2 channel
HDCP
HDMI input N/A N/A
DigitalMedia Input N/A HDCP 2.2
HDMI output N/A N/A
Security
AES-128/TLS security
Yes/TLS 1.2
Yes/TLS 1.2
802.1x
Yes
Yes
Active Directory® software
authentication
Yes
Yes
Crestron AirBoard™
Whiteboard Capture
System
Supported as a video
source
Yes as of 1/2019 FW
release,
selectable as a
source within
Smart Graphics® video
window object
Yes as of 1/2019 FW
release,
selectable as a
source within
Smart Graphics video
window object
Supported User
Interfaces
PinPoint UX™ software No No
Custom Smart Graphics
project
Yes
Yes
Crestron Pyng® OS native
project
No No
Crestron Pyng OS Smart
Graphics project
Yes
Yes
Firmware Auto Update
Supported?
Yes as of 1/2019 FW
release
, disabled by
default
Yes as of 1/2019 FW
release
, disabled by
default
Crestron Virtual
Control (VC-4)
Supported?
Yes as of 1/2019 FW
release
Yes as of 1/2019 FW
release
RSTP
Default State
Enabled (Disabled will
become the default in a
future release.)
Enabled (Disabled will
become the default in a
future release.)
(Continued on following page)
Supplemental GuideDOC. 7824C TS-1542/TS-1542-C: 15.6 in. HD Touch Screens 3
TS-1542/TS-1542-C Feature Chart (continued)
FEATURE CLASS FEATURE TS-1542 TS-1542-C
Crestron XiO Cloud™
Service
Crestron XiO Cloud
support
Yes as of 1/2019 FW
release
Yes as of 1/2019 FW
release
Firmware updates
Yes as of 1/2019 FW
release
Yes as of 1/2019 FW
release
Network settings
Yes as of 1/2019 FW
release
Yes as of 1/2019 FW
release
4 TS-1542/TS-1542-C: 15.6 in. HD Touch Screens Supplemental Guide DOC. 7824C
Access the Setup Screens
The setup screens enable basic configuration prior to regular operation of the touch
screen.
To access the setup screens during regular operation, place five fingers on the touch
screen display and hold for 15 seconds.
NOTE: The touch screen also provides a web configuration interface that may be used to
view and configure various touch screen settings. For more information, refer to
"Configuration via Web Interface," starting on page
22.
The Setup screen is displayed (TS-1542-C shown).
TS-1542-C Setup Screen
The Setup screen provides buttons for Ethernet setup, IP table setup, audio setup,
display setup, standby timeouts, and diagnostics. There is also a button to toggle system
messages on or off and an
About button that provides information about the touch
screen. Additionally, the Setup screen shows the IP address, the hostname, and the MAC
address of the touch screen.
Tap the Save & Exit button to save all settings, to exit the setup screens, and to return
to the main project.
The functions of each button are detailed in the following pages of this guide.
Supplemental GuideDOC. 7824C TS-1542/TS-1542-C: 15.6 in. HD Touch Screens 5
Configure the Device
Refer to the following sections for information about each device setup screen.
Ethernet Setup
Tap Ethernet Setup on the Setup screen to display the Ethernet Setup screen.
Ethernet Setup Screen
Use the Ethernet Setup screen to view the touch screen MAC and IP addresses, subnet
mask address, default router address, primary and secondary DNS addresses, hostname,
and domain. A
Link indicator is provided to indicate the status of the Ethernet
connection. (Green indicates that the Ethernet connection is active.)
The following buttons are provided for configuring Ethernet settings:
Tap On or Off under DHCP Enabled to turn DHCP (dynamic host configuration
protocol) on or off.
NOTE: DHCP is enabled on the touch screen by default.
If DHCP is turned off, tap Set Static IP Address Settings to enter static IP
addresses manually.
Tap Set Hostname to enter a new touch screen hostname using an on-screen
keyboard.
Tap Apply Changes to apply any new Ethernet settings to the touch screen and
to stay in setup mode.
Tap Reboot to exit setup mode and reboot the touch screen.
6 TS-1542/TS-1542-C: 15.6 in. HD Touch Screens Supplemental Guide DOC. 7824C
To change a static IP address, tap Off under DHCP Enabled. Then, tap Set Static IP
Address Settings to display the Ethernet Setup - Static IPs screen.
Ethernet Setup - Static IPs Screen
To edit the static IP address, static subnet mask, static default router, preferred DNS, or
alternate preferred DNS, tap the text field underneath the setting name.
The on-screen numeric keypad is displayed for the chosen setting.
Edit IP Address On-Screen Keypad
Supplemental GuideDOC. 7824C TS-1542/TS-1542-C: 15.6 in. HD Touch Screens 7
Use the keypad to make a new entry.
Tap the x button in the text field to clear any previous entry.
Tap the delete button
to delete the last digit.
Tap Save to save a new entry or tap the back arrow button
to discard any
changes. The display returns to the
Ethernet Setup - Static IPs screen.
After new settings have been saved, tap Apply Changes on the Ethernet Setup - Static
IPs screen to apply the new settings and stay in setup mode. Tap Reboot to exit setup
mode and reboot the touch screen.
Tap the back arrow button
to return to the Ethernet Setup screen.
Tap the back arrow button
on the Ethernet Setup screen to return to the Setup
screen.
IP Table Setup
Tap IP Table Setup on the Setup screen to display the Ethernet Setup - IP Table screen.
Ethernet Setup - IP Table Screen
Use the Ethernet Setup - IP Table screen to view and edit the IP table settings for
connecting the touch screen to a control system. The
Ethernet Setup - IP Table screen
also provides an
Online indicator for each IP table entry. (Green indicates that the
control system is online.)
To add or edit an entry, tap Add/Edit next to the corresponding entry. The Ethernet
Setup - Edit IP Table Entry screen is displayed.
8 TS-1542/TS-1542-C: 15.6 in. HD Touch Screens Supplemental Guide DOC. 7824C
Ethernet Setup - Edit IP Table Entry Screen
Tap the CIP ID text field to display the on-screen hex keypad.
Edit CIP IP On-Screen Hex Keypad
Use the keypad to make the new entry.
Tap the x button in the text field to clear any previous entry.
Tap the delete button
to delete the last digit.
Tap Save to save a new entry or tap the back arrow button
to discard any
changes. The display returns to the
Ethernet Setup - Edit IP Table Entry screen.
On the Ethernet Setup - Edit IP Table Entry screen, tap the IP Address / Hostname text
field
to display an on-screen keyboard.
Supplemental GuideDOC. 7824C TS-1542/TS-1542-C: 15.6 in. HD Touch Screens 9
Edit IP/Host On-Screen Keyboard
Use the keypad to make the new entry.
Tap the x button in the text field to clear any previous entry.
Tap the delete button
to delete the last character.
Tap Save to save a new entry or tap the back arrow button
to discard any
changes. The display returns to the
Ethernet Setup - Edit IP Table Entry screen.
On the Ethernet Setup - Edit IP Table Entry screen, tap Save Entry to save the current
entry or
Delete Entry to clear the entry.
Tap the back arrow button
to return to the Ethernet Setup - IP Table screen.
Tap the back arrow button
on the Ethernet Setup - IP Table screen to return to
the Setup
screen.
10 TS-1542/TS-1542-C: 15.6 in. HD Touch Screens Supplemental Guide DOC. 7824C
Audio Setup
Tap Audio Setup on the Setup screen to display the Audio Setup screen.
Audio Setup Screen
Use the Audio Setup screen to control the master volume, media volume, and beep
volume settings for the touch screen.
NOTE: The Media Volume controls adjust the H.264 streaming media level in relation to
the Master Volume controls.
Master Volume
- Tap the up and down arrow buttons to raise or lower the touch screen master
volume incrementally from 0 to 100%.
- Tap Mute On or Mute Off to mute or unmute the master volume.
- Tap Play Test to play a test recording at the current volume level.
Media Volume
- Tap the up and down arrow buttons to raise or lower the touch screen media
volume incrementally from 0 to 100%.
- Tap Mute On or Mute Off to mute or unmute the media volume.
Beep Volume
- Tap the up and down arrow buttons to raise or lower the touch screen beep
volume incrementally from 0 to 100%.
- Tap Beep On or Beep Off to turn the beep volume on or off.
Tap the back arrow button
to return to the Setup screen.
Supplemental GuideDOC. 7824C TS-1542/TS-1542-C: 15.6 in. HD Touch Screens 11
Display Setup
Tap Display Setup on the Setup screen to display the Display Setup screen.
Display Setup Screen
Use the Display Setup screen to adjust the LCD display settings and presets.
Tap On or Off under AutoBrightness to turn auto brightness on or off.
Tap the up and down arrows under Brightness to raise or lower the LCD display
brightness incrementally from 0 to 100%.
Tap the left and right arrow buttons under Threshold Value to raise or lower the
LCD ALS (ambient light sensor) threshold value for switching between high and
low auto-brightness presets from 0 to 100%.
Tap Presets to display the Display Setup - High & Low Settings screen.
Display Setup - High & Low Settings Screen
12 TS-1542/TS-1542-C: 15.6 in. HD Touch Screens Supplemental Guide DOC. 7824C
Use the Display Setup - High & Low Settings screen to adjust the auto-brightness
preset values for the LCD display.
Tap the up and down arrow buttons under High Preset to raise or lower the
auto-brightness value for the high preset incrementally from 0 to 100%.
Tap the up and down arrow buttons under Low Preset to raise or lower the
auto-brightness value for the low preset incrementally from 0 to 100%.
Tap the back arrow button
to return to the Display Setup screen.
Tap the back arrow button
on the Display Setup screen to return to the Setup
screen.
Standby Timeout
Tap Standby Timeout on the Setup screen to display the Standby Timeout screen.
Standby Timeout Screen
Use the Standby Timeout screen to set the standby timeout settings for the touch
screen.
Tap the up and down arrow buttons to increase the touch screen standby timeout
duration from 0 to 120 minutes.
Tap Screen Saver Options to display the Standby - Screen Saver screen.
Supplemental GuideDOC. 7824C TS-1542/TS-1542-C: 15.6 in. HD Touch Screens 13
Standby - Screen Saver Screen
Tap On or Off next to Enabled to turn the digital clock screensaver on or off
during standby timeout
Tap On or Off next to 24 Hour to turn 24-hour time format for the digital clock
on or off.
Tap the up and down arrow buttons under Screen Saver Brightness to increase
or decrease the screensaver brightness from 0 to 100%.
Tap the back arrow button
to return to the Standby Timeout screen.
Tap the back arrow button
on the Standby Timeout screen to return to the Setup
screen.
14 TS-1542/TS-1542-C: 15.6 in. HD Touch Screens Supplemental Guide DOC. 7824C
Diagnostics
Tap Diagnostics on the Setup screen to display the Diagnostics screen (TS-1542-C
shown).
Diagnostics Screen (TS-1542-C)
Use the Diagnostics screen to access various diagnostic test screens for the touch
screen. The TS-1542-C provides an additional button for configuring the DM® input
settings. The
Diagnostics screen also provides the touch screen CPU temperature and
available memory.
Each test screen is described in the sections that follow.
Supplemental GuideDOC. 7824C TS-1542/TS-1542-C: 15.6 in. HD Touch Screens 15
Test Patterns
Tap Test Patterns on the Diagnostics screen to display the Diagnostics - Test Patterns
screen.
Diagnostics - Test Patterns Screen
Use the Diagnostics - Test Patterns screen to display any of the available test patterns.
Tap one of the buttons on the screen to display its respective test pattern.
Tap the back arrow button
to return to the Diagnostics screen.
Touch Test
Tap Touch Test on the Diagnostics screen to display the touch test screen.
Touch Test Screen
16 TS-1542/TS-1542-C: 15.6 in. HD Touch Screens Supplemental Guide DOC. 7824C
Use the touch test screen to test the touch functionality of the display. When a location
button is tapped, its respective indicator lights on the screen.
Tap the back arrow button
to return to the Diagnostics screen.
Mic Test
Tap Mic Test on the Diagnostics screen to begin a microphone test.
Diagnostics - LAN Screen
During a microphone test, the built-in microphones record sound for five seconds and
then play the sound back to confirm that the microphones are functioning. This test is
performed twice: The first test records and plays sound back from the left microphone,
and the second test records and plays sound back from the right microphone.
When the second playback is finished, the display automatically returns to the
Diagnostics screen.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

Crestron TS-1542 User guide

Type
User guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI