Desa Tech MBP6 Owner's manual

Brand: Desa Tech

Model: MBP6

Category: Space heaters

Type: Owner's manual

This manual is also suitable for

Save this manual for future reference.

BLUE FLAME VENT-FREE PROPANE/LP GAS HEATER

OWNER’S OPERATION AND INSTALLATION MANUAL

MBP10LA

and

MBP6LA

— Do not store or use gasoline or other

flammable vapors and liquids in the vicinity of this or

any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s in-

structions.

• If you cannot reach your gas supplier, call the fire

department.

— Installation and service must be performed by a

qualified installer, service agency, or the gas

supplier.

WARNING: This is an

unvented gas-fired heater. It

uses air (oxygen) from the

room in which it is installed.

Provisions for adequate com-

bustion and ventilation air

must be provided. Refer to

Air

For Combustion and Ventila-

tion

on page 4 of this manual.

10,000 and 6,000 Btu/Hr

Manually-Controlled

Models

WARNING: Improper installa-

tion, adjustment, alteration, ser-

vice, or maintenance can cause

injury or property damage. Re-

fer to this manual for correct

installation and operational pro-

cedures. For assistance or ad-

ditional information consult a

qualified installer, service

agency, or the gas supplier.

WARNING: If the information in this manual is not

followed exactly, a fire or explosion may result causing

property damage, personal injury, or loss of life.

™

This appliance may be installed in an aftermarket*, permanently located, manufactured (mobile)

home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not

convertible for use with other gases.

*Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

105716

PROPANE/LP GAS HEATER

MBP10LA AND MBP6LA

™

SAFETY

INFORMATION

WARNINGS

IMPORTANT: Read this owner’s

manual carefully and completely

before trying to assemble, oper-

ate, or service this heater. Im-

proper use of this heater can

cause serious injury or death from

burns, fire, explosion, and car-

bon monoxide poisoning.

Carbon Monoxide Poisoning: Early signs

of carbon monoxide poisoning resemble the

flu, with headaches, dizziness, and/or nau-

sea. If you have these signs, the heater may

not be working properly. Get fresh air at

once! Have heater serviced. Some people

are more affected by carbon monoxide than

others. These include pregnant women,

people with heart or lung disease or anemia,

those under the influence of alcohol, and

those at high altitudes.

Propane/LP Gas: Propane/LP gas is odor-

less. An odor-making agent is added to pro-

pane/LP gas. The odor helps you detect a

propane/LP gas leak. However, the odor added

to propane/LP gas can fade. Propane/LP gas

may be present even though no odor exists.

Make certain you read and understand all

warnings. Keep this manual for reference. It

is your guide to safe and proper operation of

this heater.

DANGER: Carbon monoxide

poisoning may lead to death!

WARNING: Any change to

this heater or its controls can be

dangerous.

1. This appliance is only for use with the

type of gas indicated on the rating plate.

This appliance is not convertible for use

with other gases.

2. Do not place propane/LP supply tank(s)

inside any structure. Locate propane/

LP supply tank(s) outdoors.

3. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do

not use any phone in your building

• immediately call your gas supplier

from a neighbor’s phone. Follow the

gas supplier’s instructions

• if you cannot reach your gas supplier,

call the fire department

4. This heater needs fresh, outside air ven-

tilation to run properly. This heater has

an oxygen depletion sensor (ODS) pilot

light safety system. The ODS shuts

down the heater if not enough fresh air

is available. See Fresh Air for Combus-

tion and Ventilation, pages 4 through 6.

5. Keep all air openings in the front and

bottom of heater clear and free of de-

bris. This will insure enough air for

proper combustion.

6. If heater shuts off, do not relight until

you provide fresh, outside air. If heater

keeps shutting off, have it serviced.

7. Do not run heater

• where flammable liquids or vapors

are used or stored

• under dusty conditions

8. Do not use heater if any part has been

under water. Immediately call a quali-

fied service technician to inspect the

room heater and to replace any part of

the control system and any gas control

which has been under water.

9. Turn off heater and let cool before ser-

vicing. Only a qualified service person

should service and repair heater.

10. Operating heater above elevations of

4,500 feet could cause pilot outage.

11. To prevent performance problems, do

not use propane fuel tank of less than

100 lbs. capacity.

12. Do not install model MBP10LA in a

bathroom.

13. Before using furniture polish, wax, car-

pet cleaner, or similar products, turn

heater off. If heated, the vapors from

these products may create a white pow-

der residue within burner box or on

adjacent walls or furniture.

Do not place clothing or other

flammable material on or near

the appliance. Never place any

objects on the heater.

Surface of heater becomes very

hot when running heater. Keep

children and adults away from

hot surface to avoid burns or

clothing ignition. Heater will re-

main hot for a time after shut-

down. Allow surface to cool be-

fore touching.

Carefully supervise young chil-

dren when they are in the same

room with heater.

Make sure grill guard is in place

before running heater.

Keep the appliance area clear and

free from combustible materials,

gasoline and other flammable

vapors and liquids.

Due to high temperatures, the

appliance should be located out

of traffic and away from furniture

and draperies.

WARNING: Do not use any

accessory not approved for use

with this heater.

105716

OWNER’S MANUAL

PRODUCT

IDENTIFICATION

Figure 1 - Vent-Free Propane/LP Gas Heater (Model MBP10LA Shown)

Control Knob

Heater

Cabinet

Grill

Guard

Glass

Panel

Front

Panel

Ignitor Button

LOCAL CODES

Install and use heater with care. Follow all

local codes. In the absence of local codes, use

the latest edition of The National Fuel Gas

Code ANS Z223.1, also known as NFPA 54*.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

UNPACKING

1. Remove heater from carton.

2. Remove all protective packaging ap-

plied to heater for shipment.

3. Check heater for any shipping damage.

If heater is damaged, promptly inform

dealer where you bought heater.

PRODUCT

FEATURES

SAFETY DEVICE

This heater has a pilot with an Oxygen

Depletion Sensing (ODS) safety shutoff

system. The ODS/pilot is a required feature

for vent-free room heaters. The ODS/pilot

shuts off the heater if there is not enough

fresh air.

PIEZO IGNITION SYSTEM

This heater has a piezo ignitor. This system

requires no matches, batteries, or other

sources to light heater.

105716

PROPANE/LP GAS HEATER

MBP10LA AND MBP6LA

™

FRESH AIR FOR

COMBUSTION AND

VENTILATION

WARNING: This heater shall

not be installed in a confined space

or unusually tight construction

unless provisions are provided

for adequate combustion and ven-

tilation air. Read the following in-

structions to insure proper fresh

air for this and other fuel-burning

appliances in your home.

Today’s homes are built more energy effi-

cient than ever. New materials, increased

insulation, and new construction methods

help reduce heat loss in homes. Home owners

weather strip and caulk around windows and

doors to keep the cold air out and the warm air

in. During heating months, home owners

want their homes as airtight as possible.

While it is good to make your home energy

efficient, your home needs to breathe. Fresh

air must enter your home. All fuel-burning

appliances need fresh air for proper com-

bustion and ventilation.

Exhaust fans, fireplaces, clothes dryers, and

fuel burning appliances draw air from the

house to operate. You must provide ad-

equate fresh air for these appliances. This

will insure proper venting of vented fuel-

burning appliances.

PROVIDING ADEQUATE

VENTILATION

The following are excerpts from National

Fuel Gas Code. NFPA 54/ANS Z223.1, Sec-

tion 5.3, Air for Combustion and Ventilation.

All spaces in homes fall into one of the three

following ventilation classifications:

1. Unusually Tight Construction

2. Unconfined Space

3. Confined Space

The information on pages 4 through 6 will

help you classify your space and provide

adequate ventilation.

Unusually Tight Construction

The air that leaks around doors and win-

dows may provide enough fresh air for

combustion and ventilation. However, in

buildings of unusually tight construction,

you must provide additional fresh air.

Unusually tight construction is de-

fined as construction where:

a. walls and ceilings exposed to the

outside atmosphere have a con-

tinuous water vapor retarder with

a rating of one perm (6 x 10

-11

per pa-sec-m

) or less with open-

ings gasketed or sealed

and

b. weather stripping has been

added on openable windows and

doors

and

c. caulking or sealants are applied

to areas such as joints around

window and door frames, be-

tween sole plates and floors, be-

tween wall-ceiling joints, be-

tween wall panels, at penetra-

tions for plumbing, electrical, and

gas lines, and at other openings.

If your home meets all of the three

criteria above, you must provide ad-

ditional fresh air. See

Ventilation Air

From Outdoors

, page 6

If your home does not meet all of the

three criteria above, proceed

Deter-

mining Fresh-Air Flow for Heater Lo-

cation,

page 5.

Confined and Unconfined Space

The National Fuel Gas Code ANS Z223.1

defines a confined space as a space whose

volume is less than 50 cubic feet per 1,000

Btu per hour (4.8 m

per kw) of the aggre-

gate input rating of all appliances installed

in that space and an unconfined space as a

space whose volume is not less than 50

cubic feet per 1,000 Btu per hour (4.8 m

per

kw) of the aggregate input rating of all

appliances installed in that space. Rooms

communicating directly with the space in

which the appliances are installed*, through

openings not furnished with doors, are con-

sidered a part of the unconfined space.

This heater shall not be installed in a con-

fined space or unusually tight construction

unless provisions are provided for adequate

combustion and ventilation air.

* Adjoining rooms are communicating only

if there are doorless passageways or ventila-

tion grills between them.

105716

OWNER’S MANUAL

WARNING: If the area in which the heater may be operated is smaller than that defined as an unconfined space

or if the building is of unusually tight construction, provide adequate combustion and ventilation air by one of

the methods described in the

National Fuel Gas Code, ANS Z223.1 Section 5.3

or applicable local codes.

AIR FOR

COMBUSTION AND

VENTILATION

Continued

DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION

Determining if You Have a Confined or Unconfined Space

Use this worksheet to determine if you have a confined or unconfined space.

Space: Includes the room in which you will install heater plus any adjoining rooms with doorless passageways or ventilation grills between

the rooms.

1. Determine the volume of the space (length x width x height).

Length x Width x Height = _________________ cu. ft. (volume of space)

Example:

Space size 20 ft. (length) x 16 ft. (width) x 8 ft. (ceiling height) = 2560 cu. ft. (volume of space)

If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these rooms to the total volume of

the space.

2. Divide the space volume by 50 cubic feet to determine the maximum Btu/Hr the space can support.

_____________________(volume of space) ÷ 50 cu. ft. = (Maximum Btu/Hr the space can support)

Example:

2560 cu. ft. (volume of space) ÷ 50 cu. ft. = 51.2 or 51,200 (maximum Btu/Hr the space can support)

3. Add the Btu/Hr of all fuel burning appliances in the space.

Vent-free heater ______________ Btu/Hr

Gas water heater* ______________ Btu/Hr

Gas furnace ______________ Btu/Hr

Vented gas heater ______________ Btu/Hr

Gas fireplace logs ______________ Btu/Hr

Other gas appliances* + ______________ Btu/Hr

Total = ______________ Btu/Hr

* Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and vents to the outdoors.

4. Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.

_____________________Btu/Hr (maximum the space can support)

_____________________Btu/Hr (actual amount of Btu/Hr used)

Example:

51,200 Btu/Hr (maximum the space can support)

54,000 Btu/Hr (actual amount of Btu/Hr used)

The space in the above example is a confined space because the actual Btu/Hr used is more than the maximum Btu/Hr the space can support.

You must provide additional fresh air. Your options are as follows:

A. Rework worksheet, adding the space of an adjoining room. If the extra space provides an unconfined space, remove door to adjoin-

ing room or add ventilation grills between rooms. See Ventilation Air From Inside Building, page 6.

B. Vent room directly to the outdoors. See Ventilation Air From Outdoors, page 6.

C. Install a lower Btu/Hr heater, if lower Btu/Hr size makes room unconfined.

If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an unconfined space. You will need no

additional fresh air ventilation.

Continued

Example:

Gas water heater 44,000 Btu/Hr

Vent-free heater + 10,000 Btu/Hr

Total = 54,000 Btu/Hr

105716

PROPANE/LP GAS HEATER

MBP10LA AND MBP6LA

™

FRESH AIR FOR

COMBUSTION AND

VENTILATION

Continued

Remove

Door into

Adjoining

Room,

Option 3

Ventilation Grills

Into Adjoining Room,

Option 2

12"

Ventilation

Grills

into Adjoining

Room,

Option 1

Figure 2 - Ventilation Air from Inside Building

Figure 3 - Ventilation Air from Outdoors

Outlet

Air

Ventilated

Attic

Outlet

Air

Inlet

Air

Inlet Air

Ventilated

Crawl Space

Crawl

Space

To Attic

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation

grills or ducts. You must provide two per-

manent openings: one within 12" of the

ceiling and one within 12" of the floor.

Connect these items directly to the outdoors

or spaces open to the outdoors. These spaces

include attics and crawl spaces. Follow the

National Fuel Gas Code NFPA 54/ANS

Z223.1, Section 5.3, Air for Combustion and

Ventilation for required size of ventilation

grills or ducts.

IMPORTANT:

Do not provide openings for

inlet or outlet air into attic if attic has a

thermostat-controlled power vent. Heated air

entering the attic will activate the power vent.

VENTILATION AIR

Ventilation Air From Inside

Building

This fresh air would come from an adjoining

unconfined space. When ventilating to an

adjoining unconfined space, you must pro-

vide two permanent openings: one within

12" of the ceiling and one within 12" of the

floor on the wall connecting the two spaces

(see options 1 and 2, Figure 2). You can also

remove door into adjoining room (see op-

tion 3, Figure 2). Follow the National Fuel

Gas Code NFPA 54/ANS Z223.1, Section

5.3, Air for Combustion and Ventilation for

required size of ventilation grills or ducts.

WARNING: Rework work-

sheet, adding the space of the

adjoining unconfined space. The

combined spaces must have

enough fresh air to supply all

appliances in both spaces.

105716

OWNER’S MANUAL

For convenience and efficiency, install heater

• where there is easy access for operation,

inspection, and service

• in coldest part of room

Figure 4 - Mounting Clearances As Viewed

From Front of Heater

INSTALLING HEATER TO

WALL

Marking Screw Locations

1. Determine where you will locate heater.

2. Mark two mounting screw locations on

wall (see Figure 5).

Figure 5 - Mounting Screw Locations

Mounting

Screw

Locations

/8"

Minimum To

Maintain 6"

Clearance

From Wall

/4"

Minimum To

Maintain 3"

Clearance

From Floor

FLOOR

JOINING WALL

WARNING: Maintain minimum

clearances shown in Figure 5. If

you can, provide greater clear-

ances from floor and joining wall.

36"

FLOOR

CEILING

Minimum

Minimum To Top

Of Carpeting, Til

Combustible Ma

Minimum

From

Sides Of

Heater

Right

Side

Left

Side

INSTALLATION

WARNING: A qualified ser-

vice person must install heater.

Follow all local codes.

CHECK GAS TYPE

Use only propane/LP gas. If your gas supply

is not propane/LP, do not install heater. Call

dealer where you bought heater for proper

type heater.

INSTALLATION ITEMS

Before installing heater, make sure you have

the items listed below:

• external regulator (supplied by installer)

• piping (check local codes)

• sealant (resistant to propane/LP gas)

• equipment shutoff valve *

• ground joint union

• test gauge connection

• sediment trap

• tee joint

• pipe wrench

* A CSA/AGA design-certified equipment

shutoff valve with 1/8" NPT tap is an ac-

ceptable alternative to test gauge connec-

tion. The optional CSA/AGA design-certi-

fied equipment shutoff valve can be pur-

chased from your dealer. See Accessory,

page 18.

LOCATING HEATER

This heater is designed to be mounted on a

wall.

WARNING: Maintain the mini-

mum clearances shown in Figure

4. If you can, provide greater clear-

ances from floor, ceiling, and

joining wall.

WARNING: Never install the

heater

• in a bathroom (Model MBP10LA

only. MBP6LA is allowed in

bathroom. Check local codes.)

• in a recreational vehicle

• where curtains, furniture,

clothing, or other flammable

objects are less than 36 inches

from the front, top, or sides of

the heater

• as a fireplace insert

• in high traffic areas

• in windy or drafty areas

CAUTION: If you install the

heater in a home garage

• heater pilot and burner must

be at least 18 inches above

floor

• locate heater where moving ve-

hicle will not hit it

CAUTION: This heater cre-

ates warm air currents. These

currents move heat to wall sur-

faces next to heater. Installing

heater next to vinyl or cloth wall

coverings or operating heater

where impurities (such as to-

bacco smoke, aromatic candles,

cleaning fluids, oil or kerosene

lamps, etc.) in the air exist, may

discolor walls.

MPORTANT:

Vent-free heaters add mois-

ture to the air. Although this is beneficial,

installing heater in rooms without enough

ventilation air may cause mildew to form from

too much moisture. See Fresh Air for Com-

bustion and Ventilation, pages 4 through 6.

Minimum To

Top Surface

Of Carpeting,

Tile Or Other

Combustible

Material

NOTICE: This heater is intended

for use as supplemental heat. Use

this heater along with your pri-

mary heating system. Do not in-

stall this heater as your primary

heat source. If you have a central

heating system, you may run

system’s circulating blower while

using heater. This will help circu-

late the heat throughout the

house. In the event of a power

outage, you can use this heater

as your primary heating source.

Continued

105716

PROPANE/LP GAS HEATER

MBP10LA AND MBP6LA

™

Installing Two Mounting Screws

Note:

Wall anchors and mounting screws

are in hardware package. The hardware pack-

age is provided with heater.

Attaching to Wall Stud Method

For attaching mounting screw to wall stud

1. Drill hole at marked location using 9/64"

drill bit.

2. Insert mounting screw into wall stud.

3. Tighten screw until 1/16" space (thick-

ness of penny) is between screwhead

and wall.

Attaching to Wall Anchor Method

Follow instructions below to attach mount-

ing screws to hollow walls (wall areas be-

tween studs) or solid walls (concrete or

masonry).

1. Drill holes at marked locations using

5/16" drill bit. For solid walls (concrete

or masonry), drill at least 1

/4" deep.

2. Fold wall anchor (see Figure 6).

3. Insert wall anchor (wings first) into

hole. Tap anchor flush to wall.

4. For thin walls (1/2" or less), insert red

key into wall anchor. Push red key to

“pop” open anchor wings (see Figure 7).

IMPORTANT:

Do not hammer key!

For thick walls (over 1/2" thick) or solid

walls, do not pop open wings.

5. Tighten two screws until 1/16" space

(thickness of penny) is between

screwheads and wall (see Figure 8).

INSTALLATION

Continued

Figure 6 - Folding Anchor

Thin Walls (1/4" to 1/2" thick)

Figure 7 - Popping Open Anchor Wings

For Thin Walls

ANCHOR

Figure 8 - Tightening Anchors

Thin or

Thick Wall

(thick wall

shown)

Solid

Wall

1/16"

Space

Placing Heater On Mounting

Screws

1. Locate two keyhole slots on back panel

of heater (see Figure 9).

2. Place large openings of slots over

screwheads. Slide heater down until

screws are in small portion of slots.

Removing Front Panel Of Heater

1. Remove two screws near bottom cor-

ners of front panel.

2. Lift straight up on grill guard until it stops.

Grill guard will slide up about 1/4".

3. Pull bottom of front panel forward, then

down.

Figure 10 - Removing Front Panel Of

Heater

Installing Bottom Mounting

Screw

1. Locate bottom mounting hole. This

hole is near bottom on back panel of

heater (see Figure 11).

2. Mark screw location on wall.

3. Remove heater from wall.

4. If installing bottom mounting screw

into hollow or solid wall, install wall

anchor. Follow steps 1 through 5 un-

der Attaching To Wall Anchor Method.

If installing bottom mounting screw

into wall stud, drill hole at marked lo-

cation using 9/64" drill bit.

5. Replace heater on wall.

6. Insert bottom anchor screw through

back panel into bottom anchor or drilled

hole (see Figure 11).

7. Tighten screw until heater is firmly se-

cured to wall. Do not over tighten.

Note:

Do not replace front panel at this

time. Replace front panel after making

gas connections and checking for leaks

(see pages 9 and 10).

Figure 11 - Installing Bottom Mounting

Screw

Figure 9 - Location Of Keyhole Slots On

Back Panel Of Heater

Keyhole Slots

105716

OWNER’S MANUAL

Figure 13 - Gas Connection

Tee Joint

Reducer

Bushing to

1/8" NPT

Plug Tap

Test

Gauge

Connection *

Tee

Joint

Pipe

Nipple

Cap

Pressure

Regulator

Heater

Cabinet

3/8" NPT

Pipe Nipple

Ground Joint Union

Sediment

Trap

* A CSA/AGA design-certified equipment shutoff valve with 1/8" NPT tap is an acceptable

alternative to test gauge connection. Purchase the optional CSA/AGA design-certified

equipment shutoff valve from your dealer. See Accessory, page 18.

Equipment

Shutoff

Valve *

From

External

Regulator

(11" W.C.

to 14" W.C.

Pressure)

3" Minimum

CONNECTING TO GAS

SUPPLY

WARNING: A qualified service

person must connect heater to gas

supply. Follow all local codes.

The installer must supply an external regu-

lator. The external regulator will reduce

incoming gas pressure. You must reduce

incoming gas pressure between 11 and 14

inches of water. If you do not reduce incom-

ing gas pressure, heater regulator damage

could occur. Install external regulator with

the vent pointing down as shown in Figure

12. Pointing the vent down protects it from

freezing rain or sleet.

Install sediment trap in supply line as shown

in Figure 13. Locate sediment trap where it

is within reach for cleaning. Locate sedi-

ment trap where trapped matter is not likely

to freeze. A sediment trap traps moisture

and contaminants. This keeps them from

going into heater controls. If sediment trap

is not installed or is installed wrong, heater

may not run properly.

Installation must include a equipment shutoff

valve, ground joint union, and plugged 1/8"

NPT tap. Locate NPT tap within reach for

test gauge hook up. NPT tap must be up-

stream from heater (see Figure 13).

IMPORTANT:

Install an equipment shutoff

valve in an accessible location. The equip-

ment shutoff valve is for turning on or

shutting off the gas to the appliance.

Propane/LP

Supply Tank

Figure 12 - External Regulator With Vent

Pointing Down

CAUTION: Never connect heater

directly to the propane/LP supply.

This heater requires an external

regulator (not supplied). Install the

external regulator between the

heater and propane/LP supply.

CAUTION: Use only new,

black iron or steel pipe. Inter-

nally-tinned copper tubing may

be used in certain areas. Check

your local codes. Use pipe 3/8"

diameter or greater to allow

proper gas volume to heater. If

pipe is too small, undue loss of

pressure will occur.

CAUTION: Use pipe joint seal-

ant that is resistant to liquid pe-

troleum (LP) gas.

Vent

Pointing

Down

External

Regulator

INSTALLATION

Continued

WARNING: This appliance re-

quires a 3/8" NPT (National Pipe

Thread) inlet connection to the

pressure regulator.

IMPORTANT:

Hold pressure regulator with

wrench when connecting it to gas piping

and/or fittings.

Apply pipe joint sealant lightly to male

threads. This will prevent excess sealant

from going into pipe. Excess sealant in pipe

could result in clogged heater valves.

105716

PROPANE/LP GAS HEATER

MBP10LA AND MBP6LA

™

CHECKING GAS

CONNECTIONS

WARNING: Test all gas pip-

ing and connections for leaks

after installation or servicing.

Correct all leaks at once.

WARNING: Never use an open

flame to check for a leak. Apply a

mixture of liquid soap and water

to all joints. Bubbles forming show

a leak. Correct all leaks at once.

CAUTION: Make sure exter-

nal regulator has been installed

between propane/LP supply and

heater. See guidelines under

Con-

necting to Gas Supply

, page 9.

Pressure Testing Gas Supply

Piping System

Test Pressures In Excess Of 1/2 PSIG

(3.5 kPa)

1. Disconnect appliance with its appliance

main gas valve (control valve) and equip-

ment shutoff valve from gas supply pip-

ing system. Pressures in excess of 1/2 psig

will damage heater regulator.

2. Cap off open end of gas pipe where

equipment shutoff valve was connected.

3. Pressurize supply piping system by ei-

ther using compressed air or opening

propane/LP supply tank valve.

4. Check all joints of gas supply piping

system. Apply mixture of liquid soap

and water to gas joints. Bubbles form-

ing show a leak.

5. Correct all leaks at once.

6. Reconnect heater and equipment

shutoff valve to gas supply. Check re-

connected fittings for leaks.

Test Pressures Equal To or Less Than

1/2 PSIG (3.5 kPa)

1. Close equipment shutoff valve (see Fig-

ure 14).

2. Pressurize supply piping system by ei-

ther using compressed air or opening

propane/LP supply tank valve.

3. Check all joints from propane/LP sup-

ply tank to equipment shutoff valve (see

Figure 15). Apply mixture of liquid

soap and water to gas joints. Bubbles

forming show a leak.

4. Correct all leaks at once.

Pressure Testing Heater Gas

Connections

1. Open equipment shutoff valve (see Fig-

ure 14).

2. Open propane/LP supply tank valve.

3. Make sure control knob of heater is in

the OFF position.

4. Check all joints from equipment shutoff

valve to control valve (see Figure 15).

Apply mixture of liquid soap and wa-

ter to gas joints. Bubbles forming show

a leak.

5. Correct all leaks at once.

6. Light heater (see Operating Heater).

Check all other internal joints for leaks.

7. Turn off heater (see To Turn Off Gas

To Appliance, page 11).

8. Replace front panel.

POSI

Figure 14 - Equipment Shutoff Valve

Open

Closed

Equipment

Shutoff

Valve

Figure 15 - Checking Gas Joints

Propane/LP

Supply Tank

Control

Valve

Location

Equipment

Shutoff

Valve

OPERATING

HEATER

FOR YOUR SAFETY

READ BEFORE

LIGHTING

A. This appliance has a pilot which must

be lighted by hand. When lighting the

pilot, follow these instructions exactly.

B. BEFORE LIGHTING smell all

around the appliance area for gas. Be

sure to smell next to the floor because

some gas is heavier than air and will

settle on the floor.

WHAT TO DO IF YOU SMELL

GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do

not use any phone in your building.

• Immediately call your gas supplier

from a neighbor’s phone. Follow

the gas supplier’s instructions.

• If you cannot reach your gas sup-

plier, call the fire department.

C. Use only your hand to push in or turn

the gas control knob. Never use tools.

If the knob will not push in or turn

by hand, don’t try to repair it, call a

qualified service technician or gas

supplier. Force or attempted repair

may result in a fire or explosion.

D. Do not use this appliance if any part

has been under water. Immediately

call a qualified service technician to

inspect the appliance and to replace

any part of the control system and

any gas control which has been un-

der water.

WARNING: If you do not fol-

low these instructions exactly, a

fire or explosion may result caus-

ing property damage, personal

injury or loss of life.

INSTALLATION

Continued

105716

OWNER’S MANUAL

TO TURN OFF GAS

TO APPLIANCE

1. Remove front panel (see Figure 10,

page 8).

2. Follow steps 1 through 5 under Light-

ing Instructions.

3. With control knob pressed in, strike

match. Hold match to pilot until pi-

lot lights.

4. Keep control knob pressed in for 30

seconds after pilot is lit. After 30 sec-

onds, release control knob. Follow

step 8 under Lighting Instructions.

5. Replace front panel.

OPERATING

HEATER

Continued

CAUTION: Do not try to ad-

just heating levels by using the

equipment shutoff valve.

Thermocouple

Pilot Burner

Figure 17 - Pilot

Ignitor Electrode

LIGHTING

INSTRUCTIONS

1. STOP! Read the safety information

page 10, column 3.

2. Make sure equipment shutoff valve

is fully open.

3. Turn control knob clockwise

Clockwise

to the OFF position.

4. Wait five (5) minutes to clear out any

gas. Then smell for gas, including

near the floor. If you smell gas,

STOP! Follow “B” in the safety in-

formation, page 10, column 3. If you

don’t smell gas, go to the next step.

5. Press in control knob and turn coun-

terclockwise

C-clockwise

to the PILOT

position. Keep control knob pressed

in for five (5) seconds (see Figure 16).

Note:

You may be running this

heater for the first time after hook-

ing up to gas supply. If so, the con-

trol knob may need to be pressed in

for 30 seconds. This will allow air to

bleed from the gas system.

• If control knob does not pop up

when released, contact a qualified

service person or gas supplier for

repairs.

6. With control knob pressed in, push

down and release ignitor button. This

will light pilot. The pilot is attached

to the front of burner. The pilot can

be seen through the glass panel. If

needed, keep pressing ignitor button

until pilot lights.

Note:

If pilot does not stay lit, refer

to Troubleshooting, pages 13 through

15. Also contact a qualified service

person or gas supplier for repairs.

Until repairs are made, light pilot

with match. To light pilot with match,

see Manual Lighting Procedure.

7. Keep control knob pressed in for 30

seconds after lighting pilot. After 30

seconds, release control knob.

Note:

If pilot goes out, repeat steps

3 through 7.

OFF

HIGH

PILOT

LOW

IGNITOR

Figure 16 - Control Knob In The OFF

Position

Ignitor Button

Control Knob

Shutting Off Heater

1. Turn control knob clockwise

Clockwise

to the PILOT position.

2. Press in control knob and turn clock-

wise

Clockwise

to the OFF position.

Shutting Off Burner Only (pilot

stays lit)

Turn control knob clockwise

Clockwise

the PILOT position.

MANUAL LIGHTING

PROCEDURE

8. Turn control knob counterclockwise

C-clockwise

to the HIGH position. The

main burner should light. Set control

knob to any heat level between HIGH

and LOW. To turn control knob from

HIGH to a lower setting, press in the

control knob and turn counterclock-

wise

C-clockwise

Note:

Both HIGH and LOW are

locked positions. You must press in

control knob before turning it from

these positions.

105716

PROPANE/LP GAS HEATER

MBP10LA AND MBP6LA

™

BURNER FLAME PATTERN

Figure 20 shows a correct burner flame

pattern. Figure 21 shows an incorrect burner

flame pattern. The incorrect burner flame

pattern shows yellow tipping of the flame. It

also shows the flame higher than 1/2 the

glass panel height.

NOTICE: Do not mistake orange

flames with yellow tipping. Dust

or other fine particles enter the

heater and burn causing brief

patches of orange flame.

WARNING: If yellow tipping

occurs, your heater could pro-

duce increased levels of carbon

monoxide. If burner flame pattern

shows yellow tipping, follow in-

structions at bottom of this page.

1/2 GLASS HEIGHT

If burner flame pattern is incorrect, as shown

in Figure 21

• turn heater off (see To Turn Off Gas to

Appliance, page 11)

• see Troubleshooting, pages 13 through 15

Figure 20 - Correct Burner Flame Pattern

(Model MBP10LA is shown.

Model MBP6LA will be lower

due to lower input rating)

1/2 GLASS HEIGHT

Yellow

Tipping

Figure 21 - Incorrect Burner Flame Pattern

CLEANING AND

MAINTENANCE

CABINET

Air Passageways

• Use a vacuum cleaner or pressurized air

to clean.

Exterior

• Use a soft cloth dampened with a mild

soap and water mixture. Wipe the cabi-

net to remove dust.

WARNING: Turn off heater

and let cool before cleaning.

CAUTION: You must keep

control areas, burner, and circu-

lating air passageways of heater

clean. Inspect these areas of

heater before each use. Have

heater inspected yearly by a quali-

fied service person. Heater may

need more frequent cleaning due

to excessive lint from carpeting,

bedding material, pet hair, etc.

INSPECTING

BURNER

Check pilot flame pattern and burner flame

pattern often.

PILOT FLAME PATTERN

Figure 18 shows a correct pilot flame pat-

tern. Figure 19 shows an incorrect pilot

flame pattern. The incorrect pilot flame is

not touching the thermocouple. This will

cause the thermocouple to cool. When the

thermocouple cools, the heater will shut

down.

If pilot flame pattern is incorrect, as shown

in Figure 19

• turn heater off (see To Turn Off Gas to

Appliance, page 11)

• see Troubleshooting, pages 13 through 14

Figure 19 - Incorrect Pilot Flame Pattern

Figure 18 - Correct Pilot Flame Pattern

GRH/OV 008BAD PILOT/LP

Thermocouple

Pilot Burner

GRH/OV 007GOOD PILOT/LP

Thermocouple

Pilot Burner

CLEANING BURNER

PILOT AIR INLET HOLE

We recommend that you clean the unit ev-

ery 2,500 hours of operation or every three

months.

We also recommend that you keep the burner

tube and pilot assembly clean and free of

dust and dirt. To clean these parts we recom-

mend using compressed air no greater than

30 PSI. Your local computer store, hard-

ware store, or home center may carry com-

pressed air in a can. You can use a vacuum

cleaner in the blow position. If using com-

pressed air in a can, please follow the direc-

tions on the can. If you don't follow direc-

tions on the can, you could damage the pilot

assembly.

1. Shut off the unit, including the pilot.

Allow the unit to cool for at least thirty

minutes.

2. Inspect burner, pilot for dust and dirt.

3. Blow air through the ports/slots and

holes in the burner.

Clean the pilot assembly also. A yellow tip

on the pilot flame indicates dust and dirt in

the pilot assembly. There is a small pilot air

inlet hole about two inches from where the

pilot flame comes out of the pilot assembly

(see Figure 22). With the unit off, lightly

blow air through the air inlet hole. You may

blow through a drinking straw if compressed

air is not available.

Figure 22 - Pilot Inlet Air Hole

Pilot Assembly

Pilot Air Inlet

Hole

105716

OWNER’S MANUAL

Note:

All troubleshooting items are listed

in order of operation.

TROUBLESHOOTING

WARNING: Turn off heater

and let cool before servicing. Only

a qualified service person should

service and repair heater.

POSSIBLE CAUSE

1. Ignitor electrode positioned wrong

2. Ignitor electrode broken

3. Ignitor electrode not connected to igni-

tor cable

4. Ignitor cable pinched or wet

5. Piezo ignitor nut is loose

6. Broken ignitor cable

7. Bad piezo ignitor

1. Gas supply turned off or equipment

shutoff valve closed

2. Control knob not in PILOT position

3. Control knob not pressed in while in

PILOT position

4. Air in gas lines when installed

5. Depleted gas supply

6. ODS/pilot is clogged

7. Gas regulator setting is not correct

1. Control knob not fully pressed in

2. Control knob not pressed in long enough

3. Equipment shutoff valve not fully open

4. Thermocouple connection loose at con-

trol valve

5. Pilot flame not touching thermocouple,

which allows thermocouple to cool,

causing pilot flame to go out. This prob-

lem could be caused by one or both of

the following:

A) Low gas pressure

B) Dirty or partially clogged ODS/pilot

6. Thermocouple damaged

7. Control valve damaged

OBSERVED PROBLEM

When ignitor button is pressed, there is no

spark at ODS/pilot

When ignitor button is pressed, there is

spark at ODS/pilot but no ignition

ODS/pilot lights but flame goes out when

control knob is released

REMEDY

1. Replace ignitor

2. Replace ignitor

3. Reconnect ignitor cable

4. Free ignitor cable if pinched by any

metal or tubing. Keep ignitor cable dry

5. Tighten nut holding piezo ignitor to

heater cabinet. Nut is located inside

heater cabinet at top

6. Replace ignitor cable

7. Replace piezo ignitor

1. Turn on gas supply or open equipment

shutoff valve

2. Turn control knob to PILOT position

3. Press in control knob while in PILOT

position

4. Continue holding down control knob.

Repeat igniting operation until air is

removed

5. Contact local propane/LP gas company

6. Clean ODS/pilot (see Cleaning and

Maintenance, page 12) or replace ODS/

pilot assembly

7. Replace gas regulator

1. Press in control knob fully

2. After ODS/pilot lights, keep control

knob pressed in 30 seconds

3. Fully open equipment shutoff valve

4. Hand tighten until snug, then tighten 1/4

turn more

5. A) Contact local propane/LP gas company

B) Clean ODS/pilot (see Cleaning and

Maintenance, page 12) or replace ODS/

pilot assembly

6. Replace thermocouple

7. Replace control valve

CAUTION: Never use a wire,

needle, or similar object to clean

ODS/pilot. This can damage ODS/

pilot unit.

Continued

105716

PROPANE/LP GAS HEATER

MBP10LA AND MBP6LA

™

OBSERVED PROBLEM

Burner does not light after ODS/pilot is lit

Delayed ignition of burner

Burner backfiring during combustion

Yellow flame during burner combustion

Slight smoke or odor during initial operation

Heater produces a whistling noise when

burner is lit

Heater produces a clicking/ticking noise

just after burner is lit or shut off

White powder residue forming within burner

box or on adjacent walls or furniture

REMEDY

1. Clean burner orifice (see Cleaning and

Maintenance, page 12) or replace burner

orifice

2. Replace burner orifice

3. Contact local propane/LP gas company

1. Contact local propane/LP gas company

2. Clean burner orifice (see Cleaning and

Maintenance, page 12) or replace burner

orifice

1. Clean burner orifice (see Cleaning and

Maintenance, page 12) or replace burner

orifice

2. Replace burner

3. Replace gas regulator

1. Check burner for dirt and debris. If

found, clean burner (see Cleaning and

Maintenance, page 12)

2. Contact local propane/LP gas company

3. Replace gas regulator

1. Problem will stop after a few hours of

operation

1. Turn control knob to LOW position and

let warm up for a minute

2. Operate burner until air is removed from

line. Have gas checked by local propane/

LP gas company

3. Observe minimum installation clear-

ances (see Figure 4, page 7)

4. Clean burner (see Cleaning and Mainte-

nance, page 12) or replace burner orifice

1. This is common with most heaters. If

noise is excessive, contact qualified ser-

vice person

1. Turn heater off when using furniture

polish, wax, carpet cleaners, or similar

products

POSSIBLE CAUSE

1. Burner orifice is clogged

2. Burner orifice diameter is too small

3. Inlet gas pressure is too low

1. Manifold pressure is too low

2. Burner orifice is clogged

1. Burner orifice is clogged or damaged

2. Burner damaged

3. Gas regulator defective

1. Not enough air

2. Inlet gas pressure is too low

3. Gas regulator defective

1. Residues from manufacturing processes

1. Turning control knob to HIGH position

when burner is cold

2. Air in gas line

3. Air passageways on heater blocked

4. Dirty or partially clogged burner orifice

1. Metal expanding while heating or con-

tracting while cooling

1. When heated, vapors from furniture pol-

ish, wax, carpet cleaners, etc. turn into

white powder residue

TROUBLESHOOTING

Continued

105716

OWNER’S MANUAL

TROUBLESHOOTING

Continued

WARNING: If you smell gas

• Shut off gas supply.

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your

building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the

gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

IMPORTANT:

Operating heater where impurities in air exist may create odors. Cleaning

supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles,

etc., create fumes. These fumes may mix with combustion air and create odors.

OBSERVED PROBLEM

Heater produces unwanted odors

Heater shuts off in use (ODS operates)

Gas odor even when control knob is in OFF

position

Gas odor during combustion

Moisture/condensation noticed on windows

POSSIBLE CAUSE

1. Heater burning vapors from paint, hair

spray, glues, etc. (See

IMPORTANT

statement above)

2. Low fuel supply

3. Gas leak. See Warning statement at

top of page

1. Not enough fresh air is available

2. Low line pressure

3. ODS/pilot is partially clogged

1. Gas leak. See Warning statement at

top of page

2. Control valve defective

1. Foreign matter between control valve

and burner

2. Gas leak. See Warning statement at

top of page

1. Not enough combustion/ventilation air

REMEDY

1. Ventilate room. Stop using odor-causing

products while heater is running

2. Refill supply tank

3. Locate and correct all leaks (see Check-

ing Gas Connections, page 10)

1. Open window and/or door for ventilation

2. Contact local propane/LP gas company

3. Clean ODS/pilot (see Cleaning and

Maintenance, page 12)

1. Locate and correct all leaks (see Check-

ing Gas Connections, page 10)

2. Replace control valve

1. Take apart gas tubing and remove for-

eign matter

2. Locate and correct all leaks (see Check-

ing Gas Connections, page 10)

1. Refer to Fresh Air for Combustion and

Ventilation requirements (page 4)

105716

PROPANE/LP GAS HEATER

MBP10LA AND MBP6LA

™

MBP10LA

MBP6LA

12-2

12-1

ILLUSTRATED

PARTS LIST

105716

OWNER’S MANUAL

PARTS LIST

MBP10LA

MBP6LA

This list contains replaceable parts used in your heater. When ordering parts, follow the instructions

listed under Replacement Parts on page 18 of this manual.

PART NUMBER FOR

MBP6LA

MBP10LA

KEY

NO. DESCRIPTION QTY.

1 098304-01 098304-01 Screw, #10 x 3/8" 2

2 099467-08 099467-08 Front Panel 1

3 099318-04 099318-04 Grill Guard 1

4 101108-01 101108-01 Grill Guard Clip 2

5 102017-02 102017-02 Bottom Glass Retainer 1

6 098260-11 098260-11 Glass Panel 1

7 098532-06AA 098532-06AA Top Glass Retainer 1

8 M11084-38 M11084-38 Screw, #8 x 3/8" 8

9 098352-03BR 098352-03BR Deflector Unit 1

10 098271-03 098271-03 Ignitor Cable 1

11 098249-01 098249-01 Nut, M5 2

12 099059-03 099059-03 ODS/Pilot Assembly 1

12-1 098514-01 098514-01 Thermocouple 1

12-2 098594-01 098594-01 Ignitor Electrode 1

13 104263-02 104263-01 Burner 1

14 099387-05 099387-05 Pilot Tubing 1

15 104259-04 104259-02 Injector, 1 piece 1

16 NJF-8C NJF-8C Hex Nut 1

17 099415-13 099415-13 Pressure Regulator 1

18 099462-01 099462-01 Burner Tubing 1

19 099391-02 099391-02 Regulator Tubing 1

20 099413-02 099413-02 Control Valve 1

21 099468-16 –

Cabinet Assembly 1

– 099468-22

Cabinet Assembly 1

22 097159-04 097159-04 Piezo Ignitor 1

23 099393-02 099393-02 Control Knob 1

24 098508-01 098508-01 Valve Retainer Nut 1

25 098303-02 098303-02 Screw, #6 x 5/16" 2

26 099553-01 099553-01 Pilot Shield 1

27 099818-01 099818-01 Internal Tooth Washer 1

PARTS AVAILABLE - NOT SHOWN

099395-09 099395-06 Control Position Label 1

100642-02 100642-02 Assembly, Hardware 1

105716

PROPANE/LP GAS HEATER

MBP10LA AND MBP6LA

™

MBP6LA MBP10LA

Btu (Variable) 4,400/6,000 5,000/10,000

Type Gas Propane/LP Only Propane/LP Only

Ignition Piezo Piezo

Pressure Regulator Setting 8" W.C. 8" W.C.

Inlet Gas Pressure (inches of water)

Maximum 14" 14"

Minimum 11" 11"

Dimensions, Inches (H x W x D)

Heater 20

/2 x 13

/2 x 5 20

/2 x 13

/2 x 5

Carton 25 x 16

/16 x 7

/2 25 x 16

/16 x 7

Weight (pounds)

Heater 13.5 13.5

Shipping 19 19

Note:

Use only original replacement parts.

This will protect your warranty coverage for

parts replaced under warranty.

PARTS UNDER WARRANTY

Contact authorized dealer from whom you

purchased this product. If they cannot sup-

ply original replacement part(s),contact Cans

Unlimited, Incorporated’s Technical Ser-

vice Department at 1-800-922-7407 for re-

ferral information.

When contacting your dealer or Cans Un-

limited, Incorporated, have ready:

• your name

• your address

• model and serial numbers of your heater

• how heater was malfunctioning

• type of gas used (propane/LP or natural gas)

• purchase date

Usually, we will ask you to return the defec-

tive part to the factory.

PARTS NOT UNDER

WARRANTY

Contact authorized dealers of this product.

If they cannot supply original replacement

part(s), contact Cans Unlimited,

Incorporated’s Parts Department at 1-800-

922-7407 for referral information.

When calling Cans Unlimited, Incorporated,

have ready:

• model number of your heater

• the replacement part number

REPLACEMENT

PARTS

SPECIFICATIONS

You may have further questions about in-

stallation, operation, or troubleshooting. If

so, contact Cans Unlimited, Incorporated’s

Technical Service Department at 1-800-

922-7407.

TECHNICAL

SERVICE

SERVICE HINTS

When Gas Pressure Is Too Low

• pilot will not stay lit

• burner will have delayed ignition

• heater will not produce specified heat

• propane/LP gas supply may be low

When Gas Quality Is Bad

• pilot will not stay lit

• burner will produce flames and soot

• heater will backfire when lit

You may feel your gas pressure is too low or

gas quality is bad. If so, contact your local

propane/LP gas supplier.

EQUIPMENT SHUTOFF VALVE -

GA5010

Equipment shutoff valve with 1/8" NPT tap.

ACCESSORY

Purchase this heater accessory from your

local dealer. If they cannot supply this ac-

cessory, Cans Unlimited, Incorporated’s

Parts Department at 1-800-922-7407 for

referral information. You can also write to

the address listed on the back page of this

manual.

105716

OWNER’S MANUAL

NOTES

_______________________________________________________________________________________________

KEEP THIS WARRANTY

WARRANTY INFORMATION

Always specify model and serial numbers when communicating with the factory.

We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard written warranty.

We make no other warranty, expressed or implied.

Model

Serial No.

Date Purchased

LIMITED WARRANTY

MEDALLION VENT-FREE PROPANE/LP GAS HEATERS

Cans Unlimited, Incorporated warrants this product to be free from defects in materials and components for two (2) years from the date of

first purchase, provided that the product has been properly installed, operated and maintained in accordance with all applicable instructions.

To make a claim under this warranty the Bill of Sale or cancelled check must be presented.

This warranty is extended only to the original retail purchaser. This warranty covers the cost of part(s) required to restore this heater to proper

operating condition and an allowance for labor when provided by a Cans Unlimited, Incorporated Authorized Service Center. Warranty part(s)

MUST be obtained through authorized dealers of this product and/or Cans Unlimited, Incorporated who will provide original factory

replacement parts. Failure to use original factory replacement parts voids this warranty. The heater MUST be installed by a qualified installer

in accordance with all local codes and instructions furnished with the unit.

This warranty does not apply to parts that are not in original condition because of normal wear and tear, or parts that fail or become damaged

as a result of misuse, accidents, lack of proper maintenance or defects caused by improper installation. Travel, diagnostic cost, labor,

transportation and any and all such other costs related to repairing a defective heater will be the responsibility of the owner.

TO THE FULL EXTENT ALLOWED BY THE LAW OF THE JURISDICTION THAT GOVERNS THE SALE OF THE PRODUCT; THIS

EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED WARRANTIES AND LIMITS THE DURATION OF

ANY AND ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PAR-

TICULAR PURPOSE TO TWO (2) YEARS ON ALL COMPONENTS FROM THE DATE OF FIRST PURCHASE; AND CANS

UNLIMITED, INCORPORATED’S LIABILITY IS HEREBY LIMITED TO THE PURCHASE PRICE OF THE PRODUCT AND CANS

UNLIMITED, INCORPORATED SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES WHATSOEVER INCLUDING INDIRECT,

INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of incidental or consequential

damages, so the above limitation on implied warranties, or exclusion or limitation on damages may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.

For information about this warranty write:

105716-01

Rev. C

03/00

Distributed by: C.U.I.

Cans Unlimited, Incorporated

1700 Poplar Drive

Greer, SC 29651

105716 01

NOT A UPC

GAS PRODUCTS

™

Desa Tech MBP6 Owner's manual

Brand: Desa Tech

Model: MBP6

Category: Space heaters

Type: Owner's manual

This manual is also suitable for

Download PDF

report

Desa Tech MBP6 Owner's manual

This manual is also suitable for

Desa Tech MBP6 Owner's manual

Related papers

Other documents