Roland S-4000S-MR Owner's manual

Roland
Brand
Roland
Model
S-4000S-MR
Type
Owner's manual

This manual is also suitable for

Roland S-4000S-MR is a multi-channel audio interface that can be used for a variety of applications, including live sound reinforcement, recording, and broadcast. It features 32 analog inputs and 16 analog outputs, as well as a variety of digital audio interfaces, including REAC, Dante, and MADI. The S-4000S-MR can be used as a standalone unit or as part of a larger system, and it offers a variety of features that make it a versatile and powerful audio interface.

Some of the key features of the Roland S-4000S-MR include:

  • 32 analog inputs and 16 analog outputs
  • REAC, Dante, and MADI digital audio interfaces

Roland S-4000S-MR is a multi-channel audio interface that can be used for a variety of applications, including live sound reinforcement, recording, and broadcast. It features 32 analog inputs and 16 analog outputs, as well as a variety of digital audio interfaces, including REAC, Dante, and MADI. The S-4000S-MR can be used as a standalone unit or as part of a larger system, and it offers a variety of features that make it a versatile and powerful audio interface.

Some of the key features of the Roland S-4000S-MR include:

  • 32 analog inputs and 16 analog outputs
  • REAC, Dante, and MADI digital audio interfaces
Module Installation Rules
For the Purchaser—Please Read
When installing or detaching the SI-AD4 or SO-DA4, be sure to consult your Roland Authorized Service Center.
The rules for installing modules (SI-AD4/SO-DA4) are as follows. Be sure to follow these rules when installing.
SI
= SI-AD4
SO
= SO-DA4
z Installation must start from an odd-numbered slot.
SI SI SI SI SO SO SO SO SO
Empty
You must not begin an installation
from an even-numbered slot.
SI SI SI SI SI SO SO SO SO SO
Modules of a dierent type cannot be
installed in even-numbered slots rst.
z Group together modules of the same type. z On a device for which the REAC mode is Master, be sure to install modules in slots 1 and 2.
SI SI SI SI SI SO SOSI SI SI
Never insert modules of a dierent type in
the middle of a series of identical modules.
SI SI SI SI SO SOSI SI
EmptyEmpty
Never leave slots 1 and 2 on a
Master device empty.
On a Slave or Split device, leaving
slots 1 and 2 empty poses no
problem.
z The modules installed in a device serving as the counterpart to a device for which the REAC mode is Master need to be of a dierent type.
Master device Slave/Split device
SI-AD4
SI-AD4
SI-AD4
SI-AD4
SI-AD4
SI-AD4
SI-AD4
SI-AD4
SI-AD4
SI-AD4
SI-AD4
SI-AD4
SO-DA4
SO-DA4
SO-DA4
SO-DA4
SO-DA4
SO-DA4
The audio input into the Master device is transmitted to the modules
on the connected device (a Slave device or the like).
No audio is transmitted to empty slots.
No audio can be transmitted when the modules installed on the
connected device (a Slave device or the like) are of the same type.
Signals can be transmitted from a Slave device to the Master device.
However, transmission from a Split device to the Master device is not possible.
z About the use of slot #11
You can install a module in slot #11 that is covered by a blank panel.
Other than above rules, please note following;
• It may appear on some devices as if 8 channels have been added even though only 4
channels have actually been added to slot #11.
• When using an S-4000R, you can not see/adjust input/output status of slot #11.
• On S-4000RCS, you can not see/adjust input/output status of the slot #11 regardless its REAC
MODE (MASTER/SLAVE).
* This does not apply to S-4000S.
• If you set S-4000S as the MASTER device and connect the S-4000S to another Digital Snake
unit, the pre-amp gain, phantom ON/OFF and PAD ON/OFF settings of slot #11 will not be
memorized.
Example: 32 inputs + 12 outputs
SI SI SI SI SO
SO
SI SI
SI SI SO
Copyright © 2015 ROLAND CORPORATION 01
S-4000S
  • Page 1 1

Roland S-4000S-MR Owner's manual

Roland
Brand
Roland
Model
S-4000S-MR
Type
Owner's manual
This manual is also suitable for

Roland S-4000S-MR is a multi-channel audio interface that can be used for a variety of applications, including live sound reinforcement, recording, and broadcast. It features 32 analog inputs and 16 analog outputs, as well as a variety of digital audio interfaces, including REAC, Dante, and MADI. The S-4000S-MR can be used as a standalone unit or as part of a larger system, and it offers a variety of features that make it a versatile and powerful audio interface.

Some of the key features of the Roland S-4000S-MR include:

  • 32 analog inputs and 16 analog outputs
  • REAC, Dante, and MADI digital audio interfaces
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents