CyberPower HT705GR Quick start guide

Brand: CyberPower

Model: HT705GR

Type: Quick start guide

CyberPower HT705GR is a surge protector with advanced power-saving features that can safeguard your electronic devices and conserve energy. It comes with eight outlets, of which six are energy-saving outlets controlled by an infrared (IR) sensor. The IR sensor detects when your TV is turned off and automatically powers off the connected devices after a set time, helping you save energy. You can customize the energy-saving timer to either one or two hours.

CyberPower HT705GR is a surge protector with advanced power-saving features that can safeguard your electronic devices and conserve energy. It comes with eight outlets, of which six are energy-saving outlets controlled by an infrared (IR) sensor. The IR sensor detects when your TV is turned off and automatically powers off the connected devices after a set time, helping you save energy. You can customize the energy-saving timer to either one or two hours.

HT705GR Tier 2 APS

QUICK START GUIDE

SETUP:

1. Turn power switch to OFF. 2. Plug surge protector into wall.

5. Place glossy side of IR sensor in sightline of remotes. 6. Turn power switch to ON.

4. Connect infra-red (IR) sensor to surge

protector into small input jack.

3. Plug powered-down electronic devices in to appropriate outlets.

PEEL

Audio Equipment

DVD Player

TV

Gaming Console

without Hard Drive

Gaming Console

with Hard Drive

Cable Box DVR

/

OPERATION:

1. Power TV ON. 2. Power ON DVD player, game console, speakers, etc.

3. Energy saving timer’s default setting is 1 hour. The IR sensor’s blue LED light will blink for 15

minutes after one hour of last click of remote. Click any button on a TV remote or the volume

button on a cable provider’s remote to restart energy saving timer at zero. Blue LED light will

stop blinking for another hour.

4. Power OFF when done watching.

One Hour:

1. Hold the IR sensor button down

for 7 seconds.

2. LED light will ﬂash 3 times, release.

3. Press IR sensor 1 time.

4. LED light will ﬂash 1 time,

and timer will be 1 hour.

NOTE: IR sensor blinks for 1 minute after TV powers o. Power strip will turn o

energy saving outlets.

Two Hours:

1. Hold the IR sensor button down

for 7 seconds.

2. LED light will ﬂash 3 times, release.

3. Press IR sensor 2 times, pausing

in between.

4. LED light will ﬂash 2 times,

and timer will be 2 hours.

Need Additional Help? Feel free to contact our

Tech Support department with installation,

troubleshooting, or general product questions.

CyberPower Technical Support

1-877-297-6937 | tech@cpsww.com

cyberpowersystems.com

4241 12th Avenue E, Suite 400,

Shakopee, MN 55379, USA

Monday–Friday, 7am–6pm (CST)

This document is believed to be accurate, but CyberPower reserves

the right to change or correct the contents and does not assume

any responsibility for omissions or errors. Entire contents copyright

© 2018 Cyber Power Systems (USA), Inc. All rights reserved. Repro-

duction in whole or in part without permission is prohibited.

CHANGING ENERGY SAVING TIMER

Audio Equipment

DVR

Cable Box

Gaming Console

DVD Player

1
2
3

CyberPower HT705GR Quick start guide

Brand: CyberPower

Model: HT705GR

Type: Quick start guide

CyberPower HT705GR is a surge protector with advanced power-saving features that can safeguard your electronic devices and conserve energy. It comes with eight outlets, of which six are energy-saving outlets controlled by an infrared (IR) sensor. The IR sensor detects when your TV is turned off and automatically powers off the connected devices after a set time, helping you save energy. You can customize the energy-saving timer to either one or two hours.

Download PDF

Related papers

Other documents