Radio Shack Stereo Receiver DX-396 User manual

Brand: Radio Shack

Model: Stereo Receiver DX-396

Category: Alarm clocks

Type: User manual

This manual is also suitable for

Cat. No. 20-226

OWNER’S MANUAL

Please read before using this equipment.

DX-396

AM/SW/FM Stereo PLL Portable Receiver

20-226.fm Page 1 Tuesday, December 7, 1999 1:48 PM

FEATURES

Your lightweight and compact Ra-

dioShack DX-396 AM/SW/FM-Stereo

PLL Portable Receiver lets you choose

from a wide variety of broadcasts on

FM, AM, and SW (shortwave) bands.

The 12 international SW bands let you

tune in to the news and other programs

from such sources as the British Broad-

casting Company, Radio Cairo, and Ra-

dio Moscow, bringing the voices of the

world to you.

Its features include:

Dual Clock

— has a primary clock,

which you can set to your local time, and

a secondary clock, which you can set for

another time zone.

Phase-Locked Loop (PLL) Synthe-

sized Receiver

— ensures accurate

tuning.

Direct-Access Tuning

— directly tunes

to the desired frequency when you enter

the frequency on the keypad.

Large, Fast-Response Display

—

shows the band, frequency, wave length

(for SW), memory, battery, time, and

other indicators.

Memory Tuning

— stores up to 30 fre-

quencies in memory (10 frequencies in

each band) so you can easily tune to

your favorite stations.

DX/Local Control

— helps to reduce

distortion of broadcasts.

Tone Control

— lets you set the receiv-

er to accentuate high or low frequency

sounds.

Search Tuning

— searches up or down

the band for the next available station.

Memory Scan

— scans the stored fre-

quencies in each band’s memory.

LED Tuning Indicator

— lights when

the receiver tunes to a signal.

Shortwave Quick Select

— allows you

quick access to any of the 12 shortwave

broadcast bands.

Key Lock

— prevents you from acci-

dentally turning the receiver on or off,

changing the band or frequency, or

changing other front-panel controls.

Alarm

— sounds a buzzer or turns on

the radio at a set time.

Sleep Timer

— plays the radio for 90,

60, 30, or 15 minutes, then automatically

turns it off.

Headphone Jack

— lets you connect

optional stereo headphones so you can

listen privately and hear FM broadcasts

in stereo.

1999 Tandy Corporation.

RadioShack and Adaptaplug

are registered trademarks used by Tandy Corporation.

20-226.fm Page 2 Tuesday, December 7, 1999 1:48 PM

Three Power Options

— let you power

the receiver with internal batteries (not

supplied), standard household AC pow-

er (using an optional AC adapter), or DC

vehicle battery power (using an optional

DC adapter).

Memory Backup

— keeps the pro-

grammed stations in your receiver’s

memory for about 30 seconds without

batteries.

Frequency Step Switch

— lets you set

the correct frequency step for different

countries.

12H/24H Clock Switch

— lets you se-

lect a 12- or 24-hour time display.

Folding Stand

— securely positions the

receiver at an angle.

Because this product is so versatile,

please take a few moments to review

this Owner’s Manual before you operate

your receiver.

20-226.fm Page 3 Tuesday, December 7, 1999 1:48 PM

CONTENTS

Preparation .............................................................................................................. 5

Connecting Power .............................................................................................. 5

Using Internal Battery Power ....................................................................... 5

Using AC Power ........................................................................................... 5

Using Vehicle Battery Power ........................................................................ 6

Setting the Time ................................................................................................. 7

Choosing the Time Format ........................................................................... 7

Setting the Primary Clock ............................................................................ 7

Setting the Secondary Clock ........................................................................ 8

Setting the AM/FM Tuning Increment ................................................................. 8

Using Stereo Headphones ................................................................................. 9

Listening Safely ............................................................................................ 9

Traffic Safety ................................................................................................ 9

Using the Folding Stand ..................................................................................... 9

Operation ............................................................................................................... 10

Listening to the Receiver .................................................................................. 10

Selecting the Band ..................................................................................... 10

Selecting the International Radio Frequency Band .................................... 10

Tuning to a Radio Station ........................................................................... 11

Using the Sensitivity Switch ....................................................................... 12

Using the Antenna ..................................................................................... 12

Storing Station Frequencies ............................................................................. 12

Erasing Stored Frequencies ............................................................................. 13

Listening Hints .................................................................................................. 13

International Broadcast Frequencies ................................................................ 13

Time Standard Frequencies ............................................................................. 14

Frequency Conversion ..................................................................................... 14

Special Features ................................................................................................... 15

Using the Key Lock ........................................................................................... 15

Using the Alarm ................................................................................................ 15

Setting the Alarm Time ............................................................................... 15

Turning the Alarm On/Off ........................................................................... 15

Using the Sleep Timer ...................................................................................... 16

Troubleshooting .................................................................................................... 17

The FCC Wants You to Know ........................................................................... 18

Specifications ........................................................................................................ 19

20-226.fm Page 4 Tuesday, December 7, 1999 1:48 PM

PREPARATION

CONNECTING POWER

You can power your receiver from:

• Internal battery power (two alkaline

C batteries, not supplied).

• Standard household AC power (with

an optional AC adapter).

• Vehicle battery power (with an

optional DC adapter).

Using Internal Battery Power

To use battery power, you need two C

batteries (not supplied). For the best

performance and longest life, we recom-

mend RadioShack alkaline batteries.

Cautions:

• Use only fresh batteries of the

required size and recommended

type.

• Do not mix old and new batteries or

different types of batteries.

Follow these steps to install batteries.

1. Slide the battery compartment cover

in the direction of the arrow and

remove the cover.

2. Place the batteries in the compart-

ment and on top of the attached rib-

bon, as indicated by the polarity

symbols (+ and –) marked outside

the compartment.

3. Replace the cover.

When

BATTERY flashes on the display

or the receiver stops operating properly,

replace the batteries.

Warning:

Dispose of old batteries

promptly and properly. Do not burn or

bury them.

Caution:

If you do not plan to use the

receiver with batteries for a month, re-

move the batteries. Batteries can leak

chemicals that can destroy electronic

parts.

Using AC Power

You can power the receiver using a 3V,

700-mA AC adapter, such as Ra-

dioShack Cat. No. 273-1756, and a size

H Adaptaplug

(neither supplied). Both

are available at your local RadioShack

store.

OPEN

SIZE”C” x2 BATTERIES

20-226.fm Page 5 Tuesday, December 7, 1999 1:48 PM

Cautions:

You must use a Class 2

power source that supplies

3V DC and delivers at least

300 mA. Its center tip must be set to

positive and its plug must fit the re-

ceiver's

DC 3V

jack. Using an adapt-

er that does not meet these

specifications could damage the re-

ceiver or the adapter.

• Always connect the AC adapter to

the receiver before you connect it to

AC power. When you finish, discon-

nect the adapter from AC power

before you disconnect it from the

receiver.

• If you disconnect power from the

receiver for about 30 seconds, all

information stored in memory will be

lost. However, if you disconnect the

AC adapter plug from the receiver’s

DC 3V

jack and have batteries

installed, the memory stays intact.

Follow these steps to power the receiver

from AC power.

1. Connect the Adaptaplug to the

adapter’s cord with the TIP set to

+POS.

2. Insert the barrel plug into the

receiver’s

DC 3V

jack. This discon-

nects the internal batteries.

3. Plug the adapter into a standard AC

outlet.

Using Vehicle Battery Power

You can power the receiver from a vehi-

cle’s 12V power source (such as ciga-

rette-lighter socket) using a 3V, 300-mA

DC adapter and a size H Adaptaplug

(neither supplied). Both are available at

your local RadioShack store.

Cautions:

You must use a power

source that supplies 3V DC

and delivers at least 300

mA. Its center tip must be set to

positive and its plug must fit the re-

ceiver's

DC 3V

jack. Using an adapt-

er that does not meet these

specifications could damage the re-

ceiver or the adapter.

• Always connect the DC adapter to

the receiver before you connect it to

the power source. When you finish,

disconnect the adapter from the

power source before you disconnect

it from the receiver.

• If you disconnect power from the

receiver for about 30 seconds, all

information stored in memory will be

lost. However, if you disconnect the

DC adapter plug from the receiver’s

DC 3V

jack and have batteries

installed, the memory stays intact.

20-226.fm Page 6 Tuesday, December 7, 1999 1:48 PM

Follow these steps to power your receiv-

er from your vehicle’s battery power.

1. Set the adapter’s voltage switch to

3V.

2. Connect the Adaptaplug to the

adapter’s cord with TIP set to

+POS.

3. Insert the adapter's barrel plug into

the receiver’s

DC 3V

jack. This dis-

connects the internal batteries.

4. Plug the other end of the adapter

into your vehicle’s cigarette-lighter

socket.

SETTING THE TIME

The receiver has a dual time clock so

you can set the primary clock for your lo-

cal time and the secondary clock for an-

other time zone. You can select a 12- or

24-hour clock display format.

Choosing the Time Format

1. Slide the battery compartment cover

in the direction of the arrow and

remove the cover.

2. Remove any batteries from the com-

partment.

3. Set

CLOCK

12H

for a 12-hour for-

mat or to

24H

for a 24-hour format.

4. Replace the batteries.

5. Replace the cover.

6. Press

POWER

to turn on the

receiver and activate the format

change.

Setting the Primary Clock

Follow these steps to set your local time.

1. Press

POWER

to turn on the

receiver.

FM 87.50 MHz appears

on the display.

2. Press

CLOCK

. 12:00 slowly

flashes.

3. Press

TIME SET

. 12:00 rapidly

flashes for 60 seconds.

4. Use the number keys to enter the

correct time while the display

flashes. For example, to enter 9:30

AM, press

, and

To enter a PM time, press

MEMORY/

STORE AM/PM

. pm 9:30 appears

on the display.

Note:

You can use

to set the

time instead of using the number

keys. Press

to advance the time or

to set the time back.

5. Press

TIME SET

again when the time

shows correctly. The display stops

flashing, and the clock starts.

Notes:

• If you set the time using the time

tone from a time standard fre-

quency, press

TIME SET

when the

time tone sounds to synchronize the

seconds. (See “Time Standard Fre-

quencies” on Page 14.)

20-226.fm Page 7 Tuesday, December 7, 1999 1:48 PM

• When the receiver is off, the display

always shows local time. When the

receiver is turned on, the time disap-

pears and a radio frequency

appears. To see the time when the

receiver is on, press

CLOCK

. Press

CLOCK

again to return to the radio

frequency display.

Setting the Secondary Clock

Follow these steps to set the secondary

clock.

1. Press

POWER

, then press

DUAL

TIME

. WORLD TIME appears.

2. Press

TIME SET

. The hour digit and

WORLD TIME flash for 10 seconds.

3. While the display flashes, use the

number keys to enter the hour for

the secondary clock. Or, press

advance the hour or

to set it back.

Notes:

• The minutes change automatically,

according to the primary clock set-

ting.

• If the clock is in 12-hour format and

you press

to set the hour, PM

automatically appears on the dis-

play. If you use the number keys to

enter the hour, press

AM/PM

to note

the time is PM.

4. Press

TIME SET

again to set the

secondary clock.

To see the secondary clock time,

press

DUAL TIME

. The display

shows the time and

WORLD TIME

for 10 seconds, then automatically

returns to the primary clock time or

the radio frequency display (when

the receiver is on).

To return to the primary clock or

radio frequency display before 10

seconds have passed, press

DUAL

TIME

again.

SETTING THE AM/FM

TUNING INCREMENT

You can set the AM/FM tuning incre-

ment to the correct frequency used in

other countries as you travel.

1. Slide the battery compartment cover

in the direction of the arrow and

remove the cover.

2. Remove any batteries from the com-

partment.

To easily receive broadcasts when

you travel to other countries

, set

A/B

To easily receive broadcasts at

home

, set

A/B

For example, 10 kHz is used in

North and South America, while 9

kHz is dominant in Europe.

4. Replace the batteries.

5. Replace the cover.

20-226.fm Page 8 Tuesday, December 7, 1999 1:48 PM

USING STEREO

HEADPHONES

For private listening, connect optional

stereo headphones into the receiver's

-inch jack. Your local RadioShack store

offers a wide selection of stereo head-

phones.

Note:

The built-in speaker disconnects

when you plug in headphones.

Listening Safely

To protect your hearing, follow these

guidelines when you use headphones.

• Set the volume to the lowest setting

before you begin listening. After you

begin listening, adjust the volume to

a comfortable level.

• Do not listen at extremely high vol-

ume levels. Extended high-volume

listening can lead to permanent

hearing loss.

• Once you set the volume, do not

increase it. Over time, your ears

adapt to the volume level, so a vol-

ume level that does not cause dis-

comfort might still damage your

hearing.

Traffic Safety

Do not use headphones with your re-

ceiver when operating a motor vehicle or

riding a bicycle in or near traffic. Doing

so can create a traffic hazard and could

be illegal in some areas.

If you use headphones with your receiv-

er while riding a bicycle, be very careful.

Do not listen to a continuous broadcast.

Even though some headphones let you

hear some outside sounds when listen-

ing at normal volume levels, they still

can present a traffic hazard.

USING THE FOLDING

STAND

You can use the stand on the back of

the receiver to prop it up so you can

easily see the clock display. Simply lift

the stand away from the receiver and

set the receiver on a flat surface.

The back of the stand shows a world

map with time zone changes. You can

use the map to help you set the Second-

ary Clock to determine broadcast times

in other parts of the world.

20-226.fm Page 9 Tuesday, December 7, 1999 1:48 PM

OPERATION

LISTENING TO THE

RECEIVER

Warning:

To prevent possible ear injury

and hearing loss, set

VOLUME

to mini-

mum before you turn on the receiver. Af-

ter you turn on the receiver, set

VOLUME

to a comfortable listening level.

Follow these steps to listen to the re-

ceiver.

1. Press

POWER

to turn on the

receiver.

2. Press

BAND

until the desired band

(FM, MW, or SW) appears on the

display. (See “Selecting the Band.” )

3. Press

or the number keys (

–

) to tune to the desired station.

(See “Tuning to a Radio Station” on

Page 11.)

4. Adjust your receiver’s antenna for

the best reception. (See “Using the

Antenna” on Page 12.)

5. Adjust

VOLUME

and

TONE

desired.

6. Press

POWER

to turn off the

receiver.

Selecting the Band

You can select the Frequency Modula-

tion (FM), Medium wave (MW), or the

12-band Shortwave (SW) band for oper-

ation.

Note:

The medium wave band is also

known as the Amplitude Modulation

(AM) band due to its modulation system.

Press

BAND

until the desired band (FM,

MW, or SW) appears on the display.

•

If you select FM

, FM, MHz, and

STEREO (when you tune to a stereo

broadcast) appear on the display.

Note:

Your receiver has only one

speaker. To listen to a stereo broad-

cast, use stereo headphones (not

supplied). (See “Using Stereo Head-

phones” on Page 9.)

•

If you select MW,

MW and kHz

appear on the display.

•

If you select SW

, SW BROADCAST

BAND

, m, SW, and kHz appear on

the display. See “Selecting the Inter-

national Radio Frequency Band.” to

select each international radio fre-

quency band.

Note:

SW BROADCAST BAND and

m only appear on the display if you

select an SW frequency that falls

between the ranges printed on the

SHORTWAVE BANDS chart printed

below the display.

Selecting the International

Radio Frequency Band

If you select the shortwave band, you

can further choose one of the 12 inter-

national radio frequency bands using

SW SELECT

Follow these steps to directly select one

of the 12 SW radio broadcast bands.

1. Press

BAND

to select shortwave

band.

20-226.fm Page 10 Tuesday, December 7, 1999 1:48 PM

2. Press

SW SELECT

. m (meter) flashes

for 10 seconds.

3. While

m flashes, press the desired

band key (

120m

13m

The receiver tunes to the lowest fre-

quency in the selected band.

Tuning to a Radio Station

You can tune to a station using the man-

ual, search, direct access, preset, or

scan tuning methods.

• Up-Down Manual

To manually tune to a frequency,

repeatedly press

until the dis-

play shows the desired frequency.

•Search

To let the receiver find a station,

press and hold

for more than

2 seconds. The tuner rapidly scans

all frequencies. When you release

the button, the receiver automati-

cally tunes to the next strong sta-

tion.

Note:

As the receiver rapidly scans

for a station, you will be able to hear

the sounds broadcast from the

passing frequencies.

• Direct Access

To tune directly to a station’s fre-

quency, press

ENTER

. ENTRY

flashes for about 10 seconds. While

it is flashing, press the number but-

tons to select the desired station’s

frequency. Then press

ENTER

again.

Notes:

• Your receiver automatically

rounds the entered frequency to

the nearest valid frequency. For

example, if you try to enter a fre-

quency of 1453 in AM, your

receiver accepts it as 1450. (See

“Setting the AM/FM Tuning Incre-

ment” on Page 8.)

• If you make a mistake in entering

a frequency,

EEEE flashes on the

display. Enter the frequency

again.

• Preset

To tune directly to a station that is

entered into memory, simply press

the desired preset number (

–

Note:

You must first store the

desired stations into memory. (See

“Storing Station Frequencies” on

Page 12.)

•Scan

To scan the preset memory loca-

tions, press

SCAN

. The receiver

stops at each station for about 5

seconds. To end scanning, press

SCAN

again, or press a preset sta-

tion memory button.

Note:

If no frequency is stored in a

memory channel or no signal is

received at a memory channel, the

receiver stops at the memory chan-

nel for 1 second and then moves to

the next memory channel.

20-226.fm Page 11 Tuesday, December 7, 1999 1:48 PM

Using the Sensitivity Switch

If you are listening to a strong FM, AM,

or SW station

, and the sound is distort-

ed, set the sensitivity switch to

LOCAL

This decreases the receiver’s sensitivity

which reduces distortion from strong sig-

nals and prevents reception of weak and

noisy signals which are more common.

If you are listening to a weak station

, set

the sensitivity switch to

(distant).

This increases the receiver’s sensitivity

and improves the station’s reception.

Using the Antenna

Use the following guidelines to adjust

your receiver’s antenna.

Note:

For better AM and SW reception,

you can connect an external antenna to

the telescoping antenna.

STORING STATION

FREQUENCIES

For easy selection, you can store up to

30 of your favorite stations’ frequencies

in memory (10 frequencies in each

band; FM, MW, and SW). Once you

store a station’s frequency using a mem-

ory button, you can press this button to

select the stored station.

Caution:

If you disconnect power from

the receiver for about 30 seconds, all in-

formation stored in memory will be lost.

However, if you disconnect the AC or

DC adapter plug from the receiver’s

jack and have batteries installed, the

memory stays intact.

Follow these steps to store a frequency

in memory.

1. Press

POWER

to turn on the

receiver.

2. Press

BAND

until the desired band

(FM, MW, or SW) appears on the

display.

3. Press

or the number keys (

–

) to tune to the desired station.

4. Adjust your receiver’s antenna for

the best reception.

Note:

Use manual, search, or direct

access tuning to tune to the station’s

frequency you want to store.

5. Press

MEMORY/STORE

AM/PM

MEMORY flashes.

6. While

MEMORY flashes, press a

number button to select the memory

location.

Note:

If you do not press a number

within about 10 seconds,

MEMORY

stops flashing and you must repeat

Step 5.

Band Antenna Adjustments

Fully extend and rotate the

telescoping antenna.

Rotate the receiver.

(AM uses an internal antenna.)

Fully extend the

telescoping antenna.

20-226.fm Page 12 Tuesday, December 7, 1999 1:48 PM

ERASING STORED

FREQUENCIES

Your shortwave receiver permanently

keeps programmed stations stored in

memory. However, you can erase all or

single stored frequencies from the mem-

ory buttons.

To clear all the memory buttons

, you

must reset the receiver.

Note:

Resetting the receiver clears the

current clock settings.

Using a straightened paper clip, press

RESET

(located on the bottom of the re-

ceiver) once.

12:00 flashes on the dis-

play. Then reset the primary and

secondary clocks.

To clear a single memory button

, press

MEMORY/STORE/AM/PM

. Press the mem-

ory location button,

dELE appears. Then

press

ENTER

to clear the memory loca-

tion.

LISTENING HINTS

Listening to shortwave radio can be very

exciting. Newscasts from a country

where important events are taking place

give you a sense of immediacy that local

newscasts seldom deliver.

Although shortwave listening requires

no special knowledge, you might enjoy it

more if you read some of the numerous

books available on this subject. There

are also several periodicals that give lis-

tening hints and seasonal program

schedules.

INTERNATIONAL

BROADCAST

FREQUENCIES

International commercial broadcasts are

found in the following bands. Program-

ming (often in English) usually contains

news, commentaries, music, and special

features reflecting the culture of the

broadcasting country. You might find it

easiest to hear these broadcasts be-

tween 6:00 PM and midnight (your time).

Note:

European stations often list a fre-

quency by giving its wavelength. For ex-

ample, the 19-meter band refers to the

range of frequencies whose waves are

about 19 meters long.

*These bands are reserved for stations

in tropical areas.

Band

(In meters)

Frequency Range

(In MHz)

*120 2.300-2.495

*90 3.200-3.400

75 3.900-4.000

*60 4.750-5.060

49 5.950-6.200

**41 7.100-7.300

31 9.500-9.900

25 11.650-12.050

22 13.600-13.800

19 15.100-15.600

16 17.550-17.900

13 21.450-21.850

20-226.fm Page 13 Tuesday, December 7, 1999 1:48 PM

**The 41-meter band is shared by ham

operators in the United States and inter-

national stations.

TIME STANDARD

FREQUENCIES

The following frequencies announce the

exact time of day at specified intervals

for the United States.

Note:

Other countries also have signal

stations transmitting this type of informa-

tion over WWV or WWVH. You can find

more information about time standard fre-

quencies in Canada at www.inms.nrc.co/

inms.chu.html or in Japan at

www.crl.go.jp/cgi-bin/nph-watch.

FREQUENCY

CONVERSION

The location of a station can be ex-

pressed in frequency (KHz or MHz) or in

wavelength (meters). The following in-

formation can help you make the neces-

sary conversions.

To convert from MHz to kHz

, multiply by

1,000.

For example:

9.62 MHz x1,000=9,620 kHz

To convert from kHz to MHz

, divide by

1,000.

For example:

15,500 kHz/1,000 = 15.5 MHz

To convert from MHz to meters

, divide

300 by the number of MHz.

For example:

300/12 MHz = 25 meters

WWV

Fort Collins,

Colorado:

2.500 MHz

5.000 MHz

10.000 MHz

15.000 MHz

20.000 MHz

WWVH

Kauai, Hawaii:

10.000 MHz

15.000 MHz

20.000 MHz

20-226.fm Page 14 Tuesday, December 7, 1999 1:48 PM

SPECIAL FEATURES

USING THE KEY LOCK

The lock feature prevents you from acci-

dentally turning the receiver on or off,

changing the band or frequency, or

changing other front-panel controls. You

can still adjust

VOLUME

TONE

, and the

sensitivity switch.

To lock the controls, set

LOCK

LOCK appears on the display.

To unlock the controls, set

LOCK

LOCK disappears from the

display.

Note:

If you press a “locked” button,

briefly flashes on the display.

USING THE ALARM

Setting the Alarm Time

You can set an alarm so the buzzer

sounds or the receiver plays at a speci-

fied time.

Follow these steps to set the alarm time.

1. Hold down

SET/OFF

, BUZZER or

STANDBY appear. Press

TIME

SET

, the display flashes. Release

SET/OFF

and

TIME SET

2. While the display flashes, use the

number keys to enter an alarm time.

If the time is p.m. press

STORE AM/

once.

3. Press

TIME SET

again. The alarm

time is set. The display returns to

the radio frequency display if you

have the power on.

When you set an alarm time, the buzzer

or radio (standby) is preset for the alarm

sound. To choose the other alarm

sound, see “Turning the Alarm On/Off.”

Note:

To view the set alarm time, press

SET/OFF

. This turns off the alarm. Press

SET/OFF

again to turn the alarm back

on.

Turning the Alarm On/Off

1. Set the receiver to the desired sta-

tion and volume.

2. Press

SET/OFF

to display either

BUZZER or STANDBY , then:

• To have the buzzer sound at the

alarm time, press

ALARM/STANDBY

until BUZZER appears.

• To have the radio turn on at the

alarm time, press

ALARM/STANDBY

until STANDBY appears.

3. If the buzzer alarm is turned on, at

the preset alarm time, the buzzer

sounds for about an hour, and the

radio also plays. If the radio alarm is

turned on, at the preset alarm time,

the radio plays for 1 hour.

Note:

If you want to use the buzzer

for the alarm, set

VOLUME

to its min-

imum position.

4. To turn off the alarm, press

POWER

The alarm sounds again the next day at

the specified alarm time.

20-226.fm Page 15 Tuesday, December 7, 1999 1:48 PM

To turn off the alarm so it will not sound

again the next day, press

SET/OFF

BUZZER or STANDBY disappears

when the alarm is turned off.

USING THE SLEEP TIMER

The sleep timer sets the radio to turn off

after 90, 60, 30 or 15 minutes so you

can fall asleep as you listen to the radio.

To set the sleep timer, press

SLEEP

The radio turns on,

SLEEP

flashes and

90 appears briefly. After 90 minutes, the

radio turns off automatically.

If you want to set a shorter sleep time,

press

SLEEP

repeatedly to select 60, 30,

or 15 minutes.

Note:

Each time you press

SLEEP

, the

remaining sleep time appears briefly.

To turn off the radio before it automati-

cally turns off, press

POWER

20-226.fm Page 16 Tuesday, December 7, 1999 1:48 PM

TROUBLESHOOTING

Your receiver should give you years of trouble-free service if you follow the care in-

structions given in this manual. If you do have problems, the chart below might help

you solve them.

Problem Probable Cause Solution

No display or incorrect

display.

• Batteries are weak or dead.

• AC or DC adapter is

plugged into the receiver

but not into the power

source. (Plugging an

adapter into the receiver

automatically disconnects

the receiver’s batteries.

• DC adapter’s voltage is set

to the wrong position.

• Replace the batteries.

• Connect the adapter to the

AC or DC power source.

• Adjust DC adapter to

proper voltage position.

No sound.

• Batteries are weak or dead.

•

VOLUM

E is set too low.

• Headphones are plugged

into the receiver. (This dis-

connects the speaker.)

• AC or DC adapter is

plugged into the receiver

but not into the power

source. (Plugging an

adapter into the receiver

automatically disconnects

the receiver’s batteries.)

• Replace the batteries.

•Adjust

VOLUME

desired.

• Disconnect the head-

phones.

• Connect the adapter to the

AC or DC power source.

Weak sound, intermit-

tent sound, or poor sen-

sitivity.

• Batteries are weak.

• The sensitivity switch is set

LOCAL

• Antenna needs adjusting.

• Metal is blocking the signal.

• Replace the batteries.

• Set it to

• Adjust the antenna.

• Move the receiver near a

window when operating it

inside a vehicle or metal

frame building.

Controls do not function.

Key is locked.

LOCK

appears on the display.

Set

LOCK

to the other

position.

Display does not show

the band and frequency

for the receiver.

The clock display is selected.

Press

CLOCK

to change the

display.

20-226.fm Page 17 Tuesday, December 7, 1999 1:48 PM

THE FCC WANTS YOU TO KNOW

Your RadioShack DX-396 AM/SW/FM-Stereo PLL Portable Receiver might cause

television or radio interference even when it is operating properly. To determine

whether your receiver is causing the interference, turn it off. If the interference goes

away, your receiver is causing the interference.

To try to eliminate the interference:

• Reorient the DX-396 receiver’s antenna.

• Move your DX-396 receiver away from the television or radio receiver.

• Connect your DX-396 receiver to an outlet that is on a different electrical circuit

from the television or radio receiver.

• Contact your local RadioShack store for assistance.

If you cannot eliminate the interference, the FCC requires that you stop using your re-

ceiver.

Clock flashes.

The receiver had a power inter-

ruption.

Set the time.

Tuning does not stop.

The sensitivity switch is set to

LOCAL

. If the signal is weak,

the receiver does not stop in

LOCAL

Set it to

Scan tuning does not

stop.

• Receiver is set to memory

scan.

• No incoming signal or

scans in

LOCAL

•Press

SCAN

or press the

number key.

• Set it to

Problem Probable Cause Solution

20-226.fm Page 18 Tuesday, December 7, 1999 1:48 PM

SPECIFICATIONS

Frequency Range

(with frequency step

switch set to AM 10 kHz FM 200 kHz):

FM.................................87.5-108.0 MHz

AM ...................................530-1710 kHz

SW...............................2300-21850 kHz

( . . . set to AM 9 kHz FM 100 kHz):

FM.................................87.5-108.0 MHz

AM ...................................531-1710 kHz

SW...............................2300-21850 kHz

SW Sub-Bands:

120 meter.....................2,300-2,495 kHz

90 meter.......................3,200-3,400 kHz

75 meter.......................3,900-4,000 kHz

60 meter.......................4,750-5,060 kHz

49 meter.......................5,950-6,200 kHz

41 meter.......................7,100-7,300 kHz

31 meter.......................9,500-9,900 kHz

25 meter...................11,650-12,050 kHz

22 meter...................13,600-13,800 kHz

19 meter...................15,100-15,600 kHz

16 meter...................17,550-17,900 kHz

13 meter...................21,450-21,850 kHz

Antennas:

FM.......................................Telescoping

AM ...................................Built-In Ferrite

SW.....................(2,3 MHz - 7,095 MHz)

Built-In Ferrite

SW...............(7,100 MHz - 21,850 MHz)

Telescoping

Jacks:

External Power............................DC 3V,

Center Positive

Stereo Headphones ..................

inch

Speaker......................3 Inches (77 mm)

Permanent Magnet, Dynamic Type

Power Output:

Speaker................350 mW at 10% THD

Headphones.....35 mW x 2 at 10% THD

32 ohm

Battery Life at 10 mW.............. 60 Hours

(Alkaline Battery)

Power Source:

Internal Batteries...........Two C Batteries

(3 Volts)

AC Power................................120 Volts

with Optional AC Adapter

Vehicle Battery..........................12 Volts

with Optional DC Adapter

Sleep Timer....... 90, 60, 30, 15 minutes;

Auto-off

Dimensions (HWD):

x 4

x 1

Inches

(186.5 x 120 x 38.5 mm)

Weight...............................18 oz (503 g)

(without batteries)

Specifications are typical; individual

units might vary. Specifications are sub-

ject to change and improvement without

notice.

20-226.fm Page 19 Tuesday, December 7, 1999 1:48 PM

RadioShack

A Division of Tandy Corporation

Fort Worth, Texas 76102

12A99 Printed in Hong Kong

Limited Ninety-Day Warranty

This product is warranted by RadioShack against manufacturing defects in material and workman-

ship under normal use for ninety (90) days from the date of purchase from RadioShack company-

owned stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED

HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES,

INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,

ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES

CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABIL-

ITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RE-

SPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE

OR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WAR-

RANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVE-

NIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT,

SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN AD-

VISED OF THE POSSIBILITY OF SUCH DAMAGES.

Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of in-

cidental or consequential damages, so the above limitations or exclusions may not apply to you.

In the event of a product defect during the warranty period, take the product and the RadioShack

sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-

less otherwise provided by law: (a) correct the defect by product repair without charge for parts and

labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase

price. All replaced parts and products, and products on which a refund is made, become the prop-

erty of RadioShack. New or reconditioned parts and products may be used in the performance of

warranty service. Repaired or replaced parts and products are warranted for the remainder of the

original warranty period. You will be charged for repair or replacement of the product made after the

expiration of the warranty period.

This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,

accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or

maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs

other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as

fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs

of product removal, installation, set-up service adjustment or reinstallation.

This warranty gives you specific legal rights, and you may also have other rights which vary from

state to state.

RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102

We Service What We Sell

04/99

20-226.fm Page 20 Tuesday, December 7, 1999 1:48 PM

Radio Shack Stereo Receiver DX-396 User manual

Brand: Radio Shack

Model: Stereo Receiver DX-396

Category: Alarm clocks

Type: User manual

This manual is also suitable for

Download PDF

report

Radio Shack Stereo Receiver DX-396 User manual

This manual is also suitable for

Radio Shack Stereo Receiver DX-396 User manual

Related papers

Other documents