King Canada XL-075 User manual

Brand: King Canada

Model: XL-075

Type: User manual

King Canada XL-075 cast-iron table offers a stable and durable work surface for a variety of woodworking tasks. Its rugged construction and adjustable leveling screws ensure a precise and secure setup for your router or other woodworking tools. The table comes with a protective coating to prevent rust and is easy to clean with kerosene or paint thinner. You can further protect the table from rust by applying paste wax or rust inhibitor. The table can be mounted to the King Canada XL-085 floor stand for added stability and convenience.

ıı

x 24

ıı

CAST-IRON TABLE

MODEL: XL-075

BY/PAR:

INSTRUCTION MANUAL

2-YEAR

LIMITED WARRANTY

FOR THISCAST-IRON TABLE

KING CANADA TOOLS

OFFERS A 2-YEAR LIMITED WARRANTY

FOR NON-COMMERCIAL USE.

PROOF OF PURCHASE

Please keep your dated proof of purchase for warranty and servicing purposes.

LIMITED TOOL WARRANTY

King Canada makes every effort to ensure that this product meets high quality and durability standards. King Canada warrants to the

original retail consumer a 2-year limited warranty as of the date the product was purchased at retail and that each product is free from

defects in materials. Warranty does not apply to defects due directly or indirectly to misuse, abuse, normal wear and tear, negligence

or accidents, repairs done by an unauthorized service center, alterations and lack of maintenance. King Canada shall in no event be

liable for death, injuries to persons or property or for incidental, special or consequential damages arising from the use of our products.

To take advantage of this limited warranty, return the product at your expense together with your dated proof of purshase to an

authorized King Canada service center. Contact your retailer or visit our web site at www.kingcanada.com for an updated listing of our

authorized service centers. In cooperation with our authorized serviced center, King Canada will either repair or replace the product if

any part or parts covered under this warranty which examination proves to be defective in workmanship or material during the

warranty period.

NOTE TO USER

This instruction manual is meant to serve as a guide only. Specifications and references are subject to change without prior notice.

PARTS DIAGRAM & PARTS LISTS

Refer to the Parts section of the King Canada web site for the most updated parts diagram and parts list.

KING CANADA INC. DORVAL, QUÉBEC, CANADA H9P 2Y4

www.kingcanada.com

CLEANING, ASSEMBLY

& PARTS DIAGRAM/PARTS LIST

CLEANING

This Cast-Iron Table comes with a protective coating to prevent the table

from rusting during transport. Carefully remove table from the box. Clean

table using a rag soaked in kerosene or paint thinner, discard rag once

cleaning is done.

To further prevent rust, it is recommended to apply a light coating of paste

wax or rust inhibitor.

ASSEMBLY

MOUNTING LEVELING SCREWS AND HEX. NUTS

1) Install the 10 countersunk head screws (A) Fig.1 from underneath the

table as shown, then thread on the hex. nuts (B).

2) The hex. nuts (B) will act as leveling hardware for the Router Lift (mod.

XL-125) or the PhenolicRouter Insert Plate (mod. XL-114).

MOUNTING CAST-IRON TABLE TO FLOOR STAND (MOD. XL-085)

1) Position the Cast-Iron Table (A) Fig.2 upside down (facing down) so the

underneath of the table is exposed.

2) Position the completely assembled Floor Stand (mod. XL-085) upside

down onto the table as shown. Make sure the front of the Floor Stand

faces the front of the Cast-Iron Table.

3) Align the 6 mounting holes in the Floor Stand with those of the Cast-Iron

Table, secure the Floor Stand to the Cast-Iron Table using 6 cap screws,

spring washers and washers (B).

FIGURE 1

FIGURE 2

King Canada XL-075 User manual

King Canada XL-075 User manual

King Canada XL-075 User manual

Related papers

Other documents