3M Scotch® Wireless Weatherproofing Kit WK-101, Cold Weather Use, 10 kits/case Operating instructions

Category
Network antennas
Type
Operating instructions
Scotch
®
Wireless Weatherproofing
Kit WK-101
Instructions
CAUTION
This product should be used in accordance with
standard safety practices of the industry.
June 2010
78-8129-9298-6-A
3
2 78-8129-9298-6-A
Description
TheScotch
®
WirelessWeatherproofingKitWK-101canbeusedtocreateanenvironmental
seal,(e.g.moistureanddebris),forconnectionsfoundatwirelessinfrastructuresites.Thetapes
alsohelppreventthelooseningofconnectionscausedbyvibrations.Thekitisexcellentfor
coldweatherapplications.
KitContents
2Rollsof¾"x66'Scotch
®
Super33+
VinylElectricalTape
1Rollof2"x20'Scotch
®
Super33+
VinylElectricalTape
6Rolls–2½"x24"3M
ButylMasticTape2212
Connection Type Cable Diameter Connections per kit
LDF12 to LDF4 2 1/4"–1/2" (57–13 mm) 2
LDF7 / VXL7 to LDF4 1 5/8"–1/2" (41–13 mm) 2
LDF6 / VXL6 to LDF4 1 1/4"–1/2" (32–13 mm) 2
LDF5 / VXL5 10 LDF4 7/8"–1/2" (22–13 mm) 4
LDF4 to LDF4 1/2"–1/2" (13–13 mm) 12
VXL5 10 Device 7/8"–1/2" (22 mm–13 mm) 12
LDF4 10 Device 1/2"–1/2" (13–13 mm) 12
Table 1
1.0 Installation Recommendations:
• ApplyScotch
®
Super33+
VinylElectricalTapeattemperaturesdownto0°F(-18°C).
• Applythevinyltapeinhalf-lappedlayerswithsufficienttensiontoproduceauniform
wind.Thefinalwrapshouldbemadewithouttensiontopreventflagging.
• Alwayscutvinyltapetoimproveadhesiononfinalwrap.
• Thelastlayerofvinyltapeonaverticalconnectionshouldbeappliedfrombottomupto
createashingleeffectforwaterrun-off.
• Significantstretchingnotrecommendedforapplicationof3MButylMasticTape2212.
• Alwayscutbutylmastictapeinordertoensurecontinuityofthickness.
• Ridgesinbutylmastictapecanbesmoothedbyapplyinghandpressure.
2.0 Feeder Cable to Jumper Cable Connection
2.1 Connectthecablestothepropertorquespecification.
2.2 Ensurethecableisdryandfreeofdebrisorcablemarkers.
78-8129-9298-6-A 3
2.3 Startwrapping2"(51mm)beyond
thefeederconnectorandcreateone
half-lappedlayerof¾"(19mm)vinyl
tape.Wrap2"(51mm)pastthejumper
connectororanystrainreliefdevice.
2.4 Usingthebutylmastictape,buildupthe
jumpercablediameternearthefeeder
cabletocreateasmoothtaperedtransition.
(Tocreatetaper,stripsofbutyltapemay
befoldedinhalflengthwiseforfaster
buildup.)Tapershouldendatthesame
pointasthefirstlayerofvinyltape.
Smoothfinallayerbyhand.
2.5 Oncesmoothtaperedtransitionis
complete,usebutylmastictapetocreate
environmentalseal.Start2"(51mm)
beyondthefirstlayerofvinyltapeand
makehalf-lappedlayersextending2"(51
mm)pasttheoppositeendofthefirst
layerofvinyltape.Smoothbyhand.
2.6 Next,beginning1"(25mm)beyondthe
layerofbutylmastictapeappliedinstep
2.5,wraptheentiresectionofcablewith
oneortwolayersofhalf-lapped2"(51
mm)widevinyltapeextending1"(25
mm)beyondthelayerofbutylmastic
tape.
4 78-8129-9298-6-A
2.7 Finally,wraptheentiresectionofcable
withthreecontinuoushalf-lappedlayers
of¾"(19mm)widevinyltape.Begin
andendthefinalthreelayers1"(25mm)
beyondeachendofthepreviouslayerof
vinyltape.
3.0 Jumper Cable to Antenna Connection
3.1 Connectthecabletotheantennatothe
propertorquespecification.
3.2 Wraptheconnectionwithonelayerof
¾"(19mm)vinyltape.Start1"(25mm)
beyondthejumpercableconnector–or
strainreliefifapplicable–andwrappast
theconnectorclampingnutbutshortof
antennabase.
3.3 Cutalengthofbutylmastictapethat
willallowthetapetoextend2"(51mm)
beyondthefirstlayerofvinyltapeon
thejumpercableanduptothebaseof
theantennawhenappliedlengthwise.
Wrapthebutylmastictapearoundthe
cableconnectorandthecablelengthwise,
stretchingslightlyifnecessary,thenpress
thetapeedgestogethertoensurethereare
nogapsincoverage.Presstoconformand
smooththetapeagainsttheconnection,
cable,andbaseoftheantenna.Two
lengthwisepiecesofbutylmasticmaybe
neededtoensurecompletecoverageof
cableandconnection.
78-8129-9298-6-A 5
3.4 Starting1"belowthebutylmastictape,
wraponehalf-lappedlayerof2"(51mm)
vinyltapeuptothebaseoftheantenna.
Repeattheproceduretoapplysecondhalf-
lappedlayer.
3.5 Starting1"(25mm)belowtheprevious
layerofvinyltape,wraptheentire
cableandconnectionsectionwiththree
continuoushalf-lappedlayersof¾"(19
mm)widevinyltape.
4.0 Jumper Cable to Antenna Connection Restricted Access
Note: For installations where access to the jumper cable and antenna connector is
restricted, it is recommended to prepare the jumper cable prior to connection.
4.1 Wrapthejumpercableandconnector
bodywithonelayerof¾"(19mm)wide
vinyltapestarting1"(25mm)beyondthe
jumpercableconnector–orstrainrelief
ifapplicable–upto,butnotonto,the
connectorclampingnut.
6 78-8129-9298-6-A
4.2 Cutalengthofbutylmastictapethat
willallowthetapetoextend1"(25mm)
beyondtheinitiallayerofvinyltapeon
thejumpercableandupto,butnotonto,
theconnectorclampingnutwhenapplied
lengthwise.Slightlystretchwidthoftape
sothatitwillwrapcompletelyaroundthe
connectorbodyandcable,thenpressthe
tapeedgestogethertoensurethereareno
gapsincoverage.Presstoconformand
smooththetapeagainsttheconnector
bodyandcable.Morethanonepieceof
butylmastictapemaybeneededtoensure
fullcoverage.
4.3 Starting1"(25mm)belowthebutyl
mastictape,wraponehalf-lappedlayerof
2"(51mm)vinyltapeuptotheconnector
clampingnut.Repeatproceduretoapply
secondhalf-lappedlayer.
4.4 Starting1"(25mm)belowtheprevious
vinyltapelayer,wrapthecablewiththree
continuoushalf-lappedlayersof¾"(19
mm)wide3M
Scotch
®
Super33+
VinylElectricalTapeuptotheconnector
clampingnut.
4.5 Connectthejumpercabletothe
antennaconnectortothepropertorque
specification.
78-8129-9298-6-A 7
4.6 Start1"(25mm)belowtheconnector
clampingnutandapplyone(1)half-
lappedlayerof¾"(19mm)vinyltape
extending1"(25mm)beyondthecable
connectorclampingnut.Wrapupto,but
shortof,thebaseoftheantenna.Ifspace
restrictionspreventwrappingtapefrom
roll,thenthetapecanbeappliedinone
(1)ormorestripsifnecessary,orastrip
canbewoundontoasmallapplicator,
(e.g.apencil),andunwoundaroundthe
connectionassembly.
Note: When possible, leave some area of the
connector body exposed.
4.7 Cutalengthofbutylmastictapelong
enoughtocoverfromthebaseofthe
antennadownto1"pasttheendofthe
vinyltapelayerappliedinStep4.6when
appliedlengthwise.Wrapthebutylmastic
tapearoundthesection,stretchingslightly
ifnecessary,andthenpressthetapeedges
togethertoensuretherearenogapsin
coverage.Presstoconformandsmooth
thetapeagainsttheconnection.Morethan
onepieceofbutyltapemaybeneededto
ensurecompletecoverage.
4.8 Wraptwo(2)half-lappedlayersof2"
(51mm)vinyltapestarting1"(25mm)
beyondthebottomofthebutylmastictape
anduptothebaseoftheantenna.
4.9 Wrapthree(3)half-lappedlayersof¾"
(19mm)vinyltapestarting1"(25mm)
beyondthepreviouslayerofvinyltape,up
tothebaseoftheantenna
3M and Super33+ are trademarks of 3M Company.
Scotch is a registered trademark of 3M Company.
All other trademarks are property of their respective owners.
Important Notice
All statements, technical information, and recommendations related to 3M's products are based on information believed to be reliable,
but the accuracy or completeness is not guaranteed.
Before using this product, you must evaluate it and determine if it is suitable for
your intended application.
You assume all risks and liability associated with such use.
Any statements related to the product which are not
contained in 3M's current publications, or any contrary statements contained on your purchase order shall have no force or effect unless
expressly agreed upon, in writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture at the time of purchase.
3M MAKES NO OTHER WARRANTIES
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M's option, to replace or repair the
3M product or refund the purchase price of the 3M product.
Except where prohibited by law, 3M will not be liable for any indirect,
special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.
3
Electrical Markets Division
6801 River Place Blvd.
Austin, TX 78726-9000
800-245-3573
Fax 800-245-0329
www.3M.com/electrical
Please Recycle. Printed in USA.
© 3M 2010. All Rights
Reserved.
78-8129-9298-6-A
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

3M Scotch® Wireless Weatherproofing Kit WK-101, Cold Weather Use, 10 kits/case Operating instructions

Category
Network antennas
Type
Operating instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI