Fluke 787 ProcessMeter Digital Multimeter User manual

Fluke
Brand
Fluke
Model
787 ProcessMeter Digital Multimeter
Type
User manual

Fluke 787 ProcessMeter Digital Multimeter offers advanced troubleshooting capabilities for process control environments. It can measure volts, ohms, and amps, as well as frequency and capacitance. It also features Min/Max/Average recording, and the ability to measure temperature using an optional probe. With its rugged design and easy-to-use interface, the Fluke 787 is ideal for industrial applications.

Fluke 787 ProcessMeter Digital Multimeter offers advanced troubleshooting capabilities for process control environments. It can measure volts, ohms, and amps, as well as frequency and capacitance. It also features Min/Max/Average recording, and the ability to measure temperature using an optional probe. With its rugged design and easy-to-use interface, the Fluke 787 is ideal for industrial applications.

Manual Supplement
© 2004-2009 Fluke Corporation. All rights reserved. Printed in U.S.A. x
Manual Title: 787 Callibration Supplement Issue: 3
Part Number: 641891 Issue Date: 4/09
Print Date: May 1998 Page Count: 1
Revision/Date: 1, 9/00
This supplement contains information necessary to ensure the accuracy of
the above manual. Enter the corrections in the manual if either one of the
following conditions exist:
1. The revision letter stamped on the indicated PCA is equal to or higher
than that given with each change.
2. No revision letter is indicated at the beginning of the change.
787 Calibration Manual Supplement
4/09 1
Change #1
On page 5, under Table 2, replace the following sections of the table and delete the footnote:
Equipment Minimum Specifications Recommended Model
Digital Multimeter No Substitute Fluke 8508A
Calibration Module w/Battery
Eliminator
W No Substitute. A generic battery eliminator
might pose a safety hazard. Includes Cal
Module, Battery Eliminator, Calibration
Manual.
Fluke-787CAL 120 (USA/Canada)
Fluke-787CAL 230 (Europe)
Fluke-787CAL 240 (UK)
Fluke-787CAL 240AN (Australia)
Fluke-787CAL 100 (Japan)
Personal Computer Windows
®
95 or later (Refer to MET/CAL
®
manual set), 64 MB RAM, 500 MB on disk,
VGA monitor.
Pentium 133 MHz, IBM-compatible
Calibration Software No Substitute Fluke MET/CAL Calibration Software
On page 12, replace the Computer-Automated Verification Test Procedures with the
following:
Computer-Automated Calibration Procedures
Computer-automated verification test procedures for the 787 ProcessMeter are available on Fluke’s
MET/CAL website.
These procedures require Fluke’s MET/CAL Calibration Software, a 787 Calibration Module, a Fluke
5500A or 5520A Calibrator, and a Fluke 8508A Reference Multimeter.
Refer to the MET/CAL manual set for more information.
Change #2
On page 23, under DC Volts Measurement Test, replace steps 2 and 4 with the following:
2. Put the UUT rotary switch in the L (dc volts) position.
4. Set the UUT to the requested range, then apply the values from the calibrator shown in Table 9
and compare the readings on the UUT to the acceptable readings shown.
Change #3 W2030084
On page 4, replace the TUV symbol with the following:
®
  • Page 1 1
  • Page 2 2

Fluke 787 ProcessMeter Digital Multimeter User manual

Fluke
Brand
Fluke
Model
787 ProcessMeter Digital Multimeter
Type
User manual

Fluke 787 ProcessMeter Digital Multimeter offers advanced troubleshooting capabilities for process control environments. It can measure volts, ohms, and amps, as well as frequency and capacitance. It also features Min/Max/Average recording, and the ability to measure temperature using an optional probe. With its rugged design and easy-to-use interface, the Fluke 787 is ideal for industrial applications.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents