E1
SPECIAL WARNING
INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.
IMPORTANT: SAVE THIS INSTALLATION MANUAL FOR LOCAL ELECTRICAL INSPECTOR’S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CLEARANCES AND DIMENSIONS
For SAFETY CONSIDERATIONS do not install oven in any combustible cabinetry which is not in accord with the stated
clearances and dimensions on page 4, Figure 2 or page 7, Figure 7.
SSC3088AS SUPERSTEAM
+
OVEN
INSTALLATION MANUAL
UNPACKING YOUR OVEN
• Remove all packing materials from inside the oven.
• Check the oven for any damage, such as misaligned or bent oven,
damaged oven seals and sealing surfaces or dents inside the
cavity or on the front side of the oven. If there is any damage,
do not operate the oven and contact your dealer or a SHARP
AUTHORIZED SERVICER.
IMPORTANT NOTES TO THE INSTALLER
• Read all of the Installation Manual before installing the oven.
• Remove all packing material before connecting the electrical
supply.
• Observe all governing codes and ordinances.
• Be sure to leave these instructions with the consumer.
IMPORTANT NOTES TO THE CONSUMER
Keep this manual with your Operation Manual for future reference.
• As when using any oven generating heat, there are certain safety
precautions you should follow. These are listed in the Operation
Manual. Read all and follow carefully.
• This oven should only be installed and grounded properly by
a qualied installer or service technician.
IMPORTANT SAFETY INSTRUCTIONS
If the information in this manual is not followed
exactly, a re or electrical shock may result that could cause
property damage, personal injury or death.
• This oven must be electrically grounded in accordance with
local codes.
• Do not install this oven if the surrounding wall coverings and
the cabinets cannot withstand the heat generated by the oven.
Never leave children alone or unattended in
the area where a oven is in use.
• Do not use the Oven as a storage space. This creates a
potentially hazardous situation.
TINSKB207MRR2 JaN 8, 2016
2E
INSTALLATION HARDWARE
ITEM NAME QTY PART CODE
1
Left Mounting Bracket 1 LANGTB372MRP0
2
Right Mounting Bracket 1 LANGTB378MRP0
3
Wood Screws 8 XTSS740P20000
4
Mounting Bolts 4 LX-CZB069MRE0
5
Shoulder Bolts 2 LX-CZB068MRE0
6
Shoulder Bolt Sleeves 2 PCOVPB226MRE0
1
2
3
4
5
6
E3
15
21
/32"
(397.6 mm)
1
1
/4"
(32 mm)
2
1
/64"
(51.18mm)
16
15
/16"
(430.2 mm)
30"
(762 mm)
19
7
/8"
(504.8 mm)
19
1
/16"
(484.1 mm)
3
/4"
(19.05 mm)
FRONT BACK
Figure 1A
Figure 1B
OVEN MEASUREMENTSOVEN MEASUREMENTS
4E
Figure 2
CLEARANCES AND DIMENSIONS FOR STANDARD SURFACE MOUNT
A. 27
15
/16" cutout
B.
18
1
/8" cutout*
C. 15
3
/4" min. depth
D.
33" min. height
E. 4"
F. 18"
* Critical dimension
Note: Platform
must be able to
support 70 lbs.
E5
INSTALLATION INSTRUCTIONS FOR STANDARD SURFACE MOUNT
1. Mounting brackets should be installed with the 8 wood screws provided, 19 ¼" apart from each other and centered in the cabinet opening.
Locate position, center punch and drill pilot hole
1
/8". See Figure 3.
19
1
/4"
19
1
/4"
Front of flange even
with front of cabinet face
Front of flange even
with front of surface
90˚
*90˚
9
5
/8
"
C
L
*Note:
Square the mounting bracket
to the opening and shelf
Note: Platform must be
able to support 70 lbs.
Figure 3
6E
INSTALLATION INSTRUCTIONS FOR STANDARD SURFACE MOUNT
Always take caution lifting heavy products.
2. Use a minimum of 2 people to lift and install oven.
Place the oven adjacent to the cabinet opening, see Figure 4.
Plug the power supply cord into the electrical outlet.
3. Carefully guide the oven between the mounting brackets. Avoid
pinching the cord between the oven and the brackets.
4. Slide the oven all the way back until the oven frame is seated
against the cabinet and the mounting brackets.
DO NOT
lift this unit
using the outer
oven frame
Side Handle (x2)
Lift point
on frame
Figure 4
5. Open the oven door and insert the 4 mounting bolts supplied.
Do not completely tighten.
Figure 5
6. Open the drip tray door and insert the 2 shoulder bolts supplied.
See Figure 6. Do not completely tighten.
NOTE:
SLIDE ON SHOULDER BOLT
SLEEVES BEFORE MOUNTING
Figure 6
7. Check alignment of oven then tighten the 4 mounting bolts in
Figure 5 and the 2 shoulder bolts in Figure 6 to secure oven.
E7
CLEARANCES AND DIMENSIONS FOR FLUSH MOUNT
84"
C
A. min. 30
5
/16" max. 30
5
/8"
B. 20" cutout
C. 18
1
/8" opening*
D. 15
3
/4" min. depth
E. 33" min. height
F. 4"
G. 18"
H.
1
/4"
I. 1"
J. 1"
K.
3
/4" platform thickness
L.
7
/8" top of platform
to bottom of cutout
B
A
D
E
* Critical dimension
Note: Platform
must be able to
support 70 lbs.
Suggested
electrical
outlet location
Block added
by cabinet
installer
Steam oven
face
Steam oven
face
Note: the mounting surface of the top block
must sit 1" back from the face of the cabinet.
(allowing the face of the steam oven out
1
/4")
Detail A
Top View
Block added
by cabinet
installer
Note: the front surface of the platform must
sit 1” back from the face of the cabinet.
(allowing the face of the oven out
1
/4")
Note: the top of the
3
/4" shelf sits 1" from
the bottom of the cabinet cutout.
H J
Platform edge
Cabinet
face
Detail B
Top View
Detail C
Front View
Cabinet
cutout
K L
F
G
Cabinet
face
H
I
Figure 7
8E
Figure 8
INSTALLATION INSTRUCTIONS FOR FLUSH MOUNT
1. Install mounting brackets 19
1
/4" with the 8 wood screws provided. Locate position, center punch and drill pilot hole
1
/8". See Figure 8.
90˚
*Note:
Square the mounting bracket
to the opening and shelf
19
1
/4
"
9
5
/8
"
C
L
Front of flange even
with front of the platform
19
1
/4"
Front of flange even
with front of surface
of the installed
block
Note: Platform must be
able to support 70 lbs.
*90˚
E9
INSTALLATION INSTRUCTIONS FOR FLUSH MOUNT
Always take caution lifting heavy products.
2. Use a minimum of 2 people to lift and install oven.
Place the oven adjacent to the cabinet opening, see Figure 9.
Plug the power supply cord into the electrical outlet.
3. Carefully guide the oven between the mounting brackets. Avoid
pinching the cord between the oven and the brackets.
4. Slide the oven all the way back until the oven frame is seated
against the cabinet and the mounting brackets.
Side Handle (x2)
Lift point
on frame
DO NOT
lift this unit
using the outer
oven frame
Figure 9
5. Open the oven door and insert the 4 mounting bolts supplied.
Do not completely tighten.
Figure 10
6. Open the drip tray door and insert the 2 shoulder bolts supplied.
See Figure 11. Do not completely tighten.
NOTE:
SLIDE ON SHOULDER BOLT
SLEEVES BEFORE MOUNTING
Figure 11
7. Check alignment of oven then tighten the 4 mounting bolts in
Figure 10 and the 2 shoulder bolts in Figure 11 to secure oven.
10E
ELECTRICAL OUTLET
The electrical requirements are a 120 volt 60 Hz, AC only, 15
amp. or more protected electrical supply. It is recommended that
a separate circuit serving only this appliance be provided.
The oven is equipped with a 3-prong grounding plug. It must
be plugged into a wall receptacle that is properly installed and
grounded. Should you only have a 2-prong outlet, have a qualied
electrician install a correct wall receptacle.
Note: If you have any questions about the grounding or electrical
instructions, consult a qualied electrician or service person.
* Can also be installed using an electrical outlet in an adjacent cabinet
within the area where the provided electrical cord can reach.
Always check electrical codes for requirements.
GROUNDING INSTRUCTIONS
This appliance must be grounded. The oven is equipped with a
3-prong plug which includes a grounding pin. It must be plugged
into a wall receptacle that is properly installed and grounded in
accordance with the National Electrical Code and local codes
and ordinances. In the event of an electrical short circuit,
grounding reduces risk of electric shock by providing an escape
wire for the electric current.
– Improper use of the grounding plug can result
in a risk of electric shock. Do not use an extension cord. If the
power supply cord is too short, have a qualied electrician or
serviceman install an outlet near the appliance.
BEFORE YOU CALL FOR SERVICE
Read the BEFORE YOU CALL and operating instruction sections
in your Operation Manual. It may save you time and expense.
The list includes common occurrences that are not the result of
defective workmanship or materials in this range.
Refer to the warranty in your Operation Manual for Sharp’s
toll-free service number and address. Please call or write if you
have inquiries about your microwave product and/or need to
order parts.
MODEL AND SERIAL NUMBER LOCATION
The model number and serial number are printed on the name-
plate. To access the nameplate, open the drip tray door and remove
the drip tray. The nameplate is located to the left of the reservoir.
Nameplate Location
CARE, CLEANING AND MAINTENANCE
Refer to the Operation Manual for cleaning instructions.
SHARP ELECTRONICS CORPORATION • 1 Sharp Plaza, Suite 1 • Mahwah, New Jersey 07495-1123 • USA
SHARP ELECTRONICS OF CANADA LTD •
335 Britannia Road East • Mississauga, ON L4Z 1W9 • Canada
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Viking MVSOC530SS Installation guide
-
Yes SSC2489DS Installation guide
-
Jenn-Air JGRP548HL00 Installation guide
-
KitchenAid KDRS467VBK00 Installation guide
-
-
Whirlpool UMH50008HS0 Installation guide
-
-
Thermador PRD486JDGU Installation guide
-
Whirlpool UMH50008HS Installation guide
-