Sharp MX-C400P Owner's manual

Brand: Sharp

Model: MX-C400P

Category: Copiers

Type: Owner's manual

Sharp MX-C400P is a digital full-color printer offering high-quality prints with fast speeds, capable of producing vibrant color copies and prints, enabling efficient document handling for professional use.

INSTALLATION

REQUIREMENTS

SUPPLIES

TO THE ADMINISTRATOR

OF THE MACHINE

SPECIFICATIONS

DIGITAL FULL COLOR PRINTER

Please read first

Please read this guide first to ensure safe

use of the machine.

Before installing this product, be sure to

read the "TO ENSURE SAFE USE OF THE

MACHINE" and "INSTALLATION

REQUIREMENTS" sections.

Keep this manual close at hand

for reference whenever needed.

MX-C400PMODEL:

Safety GuideSafety GuideSafety Guide

CAUTIONS

MX-C400P Safety Guide

D IN CHINA

9M KS1

E4632FCZZ

mxc400p_us_saf.book -1 ページ２００９年１０月５日　月曜日　午後１時５３分

Notice for Users in U.S.A.

EMC (this machine and peripheral devices)

NOTE:

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to correct

the interference at his own expense.

Each instruction also covers the optional units used with these products.

Caution!

For complete electrical disconnection, pull out the main plug.

The socket-outlet should be installed near the equipment and should be easily

accessible.

FOR YOUR RECORDS ...

To protect against loss or theft, record and retain for reference the machine's serial

number located at the lower left corner of the left side of the machine.

Model Number

Serial Number

Date of Purchase

Place of Purchase

Authorized Sharp Dealer

Service Department Number

WARNING:

FCC Regulations state that any unauthorized changes or modifications to this

equipment not expressly approved by the manufacturer could void the user's authority

to operate this equipment.

Shielded interface cables must be used with this equipment to maintain compliance

with EMC regulations.

This machine contains software modules developed by Independent JPEG Group.

This product includes Adobe

Flash

technology of Adobe Systems Incorporated.

mxc400p_us_saf.book 0 ページ２００９年１０月５日　月曜日　午後１時５３分

Contents

CAUTIONS . . . . . . . . . . . . . . . . . 3

Laser information . . . . . . . . . . . . 8

INSTALLATION REQUIREMENTS . . .

SUPPLIES. . . . . . . . . . . . . . . . . 11

Storage of supplies. . . . . . . . . . 11

Supply of spare parts and

consumables . . . . . . . . . . . . . . 11

SPECIFICATIONS . . . . . . . . . . 12

Machine specifications . . . . . . . 12

Continuous printing speeds . . . 16

Ambient environment . . . . . . . . 16

Acoustic noise emission

(measurement according to

ISO7779) . . . . . . . . . . . . . . . . . 17

Chemical emission (measured

according to RALUZ122: Edition

Jun. 2006) . . . . . . . . . . . . . . . . 17

500-sheet paper feed unit

specifications . . . . . . . . . . . . . . 18

Finisher specifications . . . . . . . 19

TO THE ADMINISTRATOR OF

THE MACHINE . . . . . . . . . . . . . 22

Factory default passwords . . . . 22

Trademark acknowledgments . . .

mxc400p_us_saf_01.fm 1 ページ２００９年１０月１２日　月曜日　午前８時２５分

Warranty

While every effort has been made to make this document as accurate and helpful as

possible, SHARP Corporation makes no warranty of any kind with regard to its content.

All information included herein is subject to change without notice. SHARP is not

responsible for any loss or damages, direct or indirect, arising from or related to the use

of this operation manual.

translation without prior written permission is prohibited, except as allowed under

Note:

• Considerable care has been taken in preparing this manual. If you have any

comments or concerns about the manual, please contact your dealer or nearest

SHARP Service Department.

• This product has undergone strict quality control and inspection procedures. In the

unlikely event that a defect or other problem is discovered, please contact your

dealer or nearest SHARP Service Department.

• Aside from instances provided for by law, SHARP is not responsible for failures

occurring during the use of the product or its options, or failures due to incorrect

operation of the product and its options, or other failures, or for any damage that

occurs due to use of the product.

Products that have earned the ENERGY STAR

are designed to

protect the environment through superior energy efficiency.

The Environmental Choice Program guidelines are applied to the

products only in Canada. The products that meet the

Environmental Choice Program guidelines carry the logo shown

to the left. The products without the logo may not meet the

Environmental Choice Program guidelines.

mxc400p_us_saf.book 2 ページ２００９年１０月５日　月曜日　午後１時５３分

CAUTIONS

Symbols in this manual

To ensure safe use of the machine, this manual uses various safety symbols. The

safety symbols are classified as explained below. Be sure you understand the meaning

of the symbols when reading the manual.

WARNING Indicates a risk of death or serious injury.

CAUTION Indicates a risk of human injury or property damage.

Meaning of the symbols

The symbol indicates the need for caution. The specific matter that requires

caution is indicated inside the symbol (the symbol at left indicates "caution: high

temperature").

The symbol indicates an action that is prohibited. The specific action that is

prohibited is indicated inside or beside the symbol (the symbol at left indicates

"disassembly is prohibited").

The symbol indicates an action that is mandatory.

WARNING

Do not remove the machine casing.

High-voltage parts inside the machine may cause electrical shock.

Be sure to connect the power cord only to a power outlet that

meets the specified voltage and current requirements. Also

make certain the outlet is properly grounded. Do not use an

extension cord or adapter to connect other devices to the power

outlet used by the machine. Using an improper power supply

may cause fire or electrical shock.

*For the power supply requirements, see the name plate in the lower left

corner of the left side of the machine.

Do not damage or modify the power cord.

Placing heavy objects on the power cord, pulling it, or forcibly

bending it will damage the cord, resulting in fire or electrical shock.

Do not place a container of water or other liquid, or a metal

object that might fall inside, on the machine.

If the liquid spills or the object falls into the machine, fire or

electrical shock may result.

mxc400p_us_saf_01.fm 3 ページ２００９年１０月１４日　水曜日　午後１時３７分

CAUTIONS

WARNING

Do not insert or remove the power plug with wet hands.

This may cause electrical shock.

Do not use a flammable spray to clean the machine.

If gas from the spray comes in contact with hot electrical components

or the fusing unit inside the machine, fire or electrical shock may result.

Do not make any modifications to this machine.

Doing so may result in personal injury or damage to the machine.

If a thunder storm begins, switch off the main power and remove

the power plug from the outlet to prevent electrical shock and

fire due to lightning.

If you notice smoke, a strange odor, or other abnormality, do

not use the machine.

If used in this condition, fire or electrical shock may result.

Immediately switch off the main power and remove the power plug

from the power outlet. Contact your dealer or nearest SHARP Service Department.

If a piece of metal or water enters the machine, switch off the

main power and remove the power plug from the power outlet.

Contact your dealer or nearest SHARP Service Department. Using

the machine in this condition may result in electrical shock or fire.

mxc400p_us_saf.book 4 ページ２００９年１０月５日　月曜日　午後１時５３分

CAUTIONS

CAUTION

Do not throw toner, a toner container (toner cartridge), or a

waste toner box into a fire.

Toner may fly and cause burns.

Do not install in a location with moisture or dust.

Risk of fire and electrical shock.

Do not install the machine on an unstable or slanted surface. Install the

machine on a surface that can withstand the weight of the machine.

There is a risk of injury due to the machine falling or toppling. If peripheral

devices are to be installed, do not install on an uneven floor, slanted surface,

or otherwise unstable surface. There is a danger of slippage, falling, and toppling. Install

the product on a flat, stable surface that can withstand the weight of the product. (Weight

when various peripheral devices are installed: approx. 132.3 lbs. (60 kg))

Do not touch the transfer belt or the transfer roller.

Scratches or smudges on the transfer belt or the transfer roller will

cause dirty prints.

When removing the power plug from the outlet, do not pull on the cord.

Pulling on the cord may cause damage such as wire exposure and

breakage, and may result in fire or electrical shock.

Do not block the ventilation ports on the machine. Do not install

the machine in a location that will block the ventilation ports.

Blocking the ventilation ports will cause heat to build up in the

machine, creating a risk of fire.

If you find that condensation has formed on the surface of the

machine or the display, open the right cover and check for

condensation inside the machine. If condensation has formed

inside the machine, turn off the main power. Turning on the main

power when condensation has formed inside the machine may cause a failure.

Leave the right cover open until the condensation evaporates naturally.

To keep foreign matter from getting on the primary transfer belt unit or secondary

transfer roller unit while the right cover is open, place a cover over the opening.

Store toner, toner containers (toner cartridges), and

waste toner boxes out of the reach of children.

mxc400p_us_saf_01.fm 5 ページ２００９年１０月９日　金曜日　午前１０時４３分

CAUTIONS

CAUTION

When moving the machine, switch off the main power and

remove the power plug from the outlet before moving.

The cord may be damaged, creating a risk of fire or electrical shock.

If you will not use the machine for a long time, be sure to

remove the power plug from the outlet for safety.

The fusing unit is hot. When removing a

misfeed, do not touch the fusing unit.

Take care not to burn yourself.

When loading paper, removing a misfeed,

performing maintenance, closing the front

and side covers, and inserting and removing

trays, take care that your fingers are not

pinched.

The machine is heavy. To prevent injury when moving the

machine, it is recommended that it be moved by two or more

persons.

Fusing unit

mxc400p_us_saf.book 6 ページ２００９年１０月５日　月曜日　午後１時５３分

CAUTIONS

The machine includes the print hold function, which stores document image data on the

machine's hard drive. Stored documents can be called up and printed as needed. If a

hard drive failure occurs, it will no longer be possible to call up the stored document

data. To prevent the loss of important documents in the unlikely event of a hard drive

failure, store the original data elsewhere.

With the exception of instances provided for by law, Sharp Corporation bears no

responsibility for any damages or loss due to the loss of stored document data.

"BATTERY DISPOSAL"

THIS PRODUCT CONTAINS A LITHIUM PRIMARY MEMORY BACK-UP BATTERY

THAT MUST BE DISPOSED OF PROPERLY. PLEASE CONTACT YOUR LOCAL

SHARP DEALER OR AUTHORIZED SERVICE REPRESENTATIVE FOR

ASSISTANCE IN DISPOSING OF THIS BATTERY.

This product utilizes a CR coin Lithium battery which contains a Perchlorate material.

Special handling for this material may apply, California residents, See

www.dtsc.ca.gov/hazardouswaste/perchlorate/

Others, consult local environmental officers.

This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of

mercury. Disposal of these materials may be regulated due to environmental

consideration. For disposal or recycling information, please contact your local

authorities, the Electronics Industries Alliance: www.eiae.org, the lamp recycling

organization: www.lamprecycle.org or Sharp at 1-800-BE-SHARP.

(For U.S.A. Only)

Non LPS

Do not connect to devices other than

specified peripheral devices of our company.

For North America

mxc400p_us_saf.book 7 ページ２００９年１０月５日　月曜日　午後１時５３分

CAUTIONS

Laser information

Wave length 790 nm ± 10 nm

Pulse times

(North America and Europe)

4.1 µs ± 4.1 ns / 7 mm

Output power Max 0.6 mW (LD1+ LD2)

Caution

Use of controls or adjustments or performance of procedures other than those specified

herein may result in hazardous radiation exposure.

This Digital Equipment is CLASS 1 LASER PRODUCT (IEC 60825-1 Edition 1.2-2001)

For North America:

SAFETY PRECAUTIONS

This Digital Equipment is rated Class 1 and complies with 21 CFR 1040.10 and

1040.11 of the CDRH standards. This means that the equipment does not produce

hazardous laser radiation. For your safety, observe the precautions below.

• Do not remove the cabinet, operation panel or any other covers.

• The equipment's exterior covers contain several safety interlock switches. Do not

bypass any safety interlock by inserting wedges or other items into switch slots.

For Europe:

CLASS 1 LASER PRODUCT

LASER KLASSE 1

LUOKAN 1 LASERLAITE

KLASS 1 LASERAPPARAT

mxc400p_us_saf.book 8 ページ２００９年１０月５日　月曜日　午後１時５３分

INSTALLATION REQUIREMENTS

The performance of the machine is affected by the ambient conditions of the

installation location. Do not install in the following locations:

Do not install the machine in

locations that are excessively

hot, cold, humid, or dry (near

heaters, humidifiers, air

conditioners, etc.)

The paper will become damp and

condensation may form inside the

machine, causing misfeeds and dirty

output.

☞ Ambient environment (page 16)

If the location has an ultrasonic humidifier,

use pure water in the humidifier. If tap

water is used, minerals and other

impurities will be emitted, causing

impurities to collect on the inside of the

machine and create dirty output.

Exercise care not to expose the paper exit

part of the machine to wind or exhaust air.

The output paper may be blown to the

floor.

Near a wall

Be sure to allow the required space

around the machine for servicing and

proper ventilation. (The machine should

be no closer than the distances indicated

below from walls.)

CAUTION:

Do not install the machine in

a location with poor air

circulation.

A small amount of ozone is created

inside the machine during printing. The

amount of ozone created is not sufficient

to be harmful; however, an unpleasant

odor may be noticed during large printing

runs, and thus the machine should be

installed in a room with a ventilation fan

or windows that provide sufficient air

circulation. (The odor may occasionally

cause headaches.)

* Install the machine so that people are

not directly exposed to exhaust from

the machine. If installed near a

window, ensure that the machine is not

exposed to direct sunlight.

17-23/32"

(45cm)

11-13/16"

(30cm)

11-13/16"

(30cm)

mxc400p_us_saf_01.fm 9 ページ２００９年１０月５日　月曜日　午後８時１０分

INSTALLATION REQUIREMENTS

Dusty locations

If dust enters the machine, dirty output and

machine failure may result.

Locations exposed to direct

sunlight

Plastic parts may become deformed and

dirty output may result.

Locations with ammonia gas

Installing the machine next to a diazo copy

machine may cause dirty output.

Locations subject to

vibration.

Vibration may cause failure.

The machine includes a built-in hard drive. Do not subject the machine to

shock or vibration. In particular, never move the machine while the power

is on.

• The machine should be installed near an accessible power outlet for easy

connection.

• Connect the machine to a power outlet which is not used for other electric

appliances. If a lighting fixture is connected to the same outlet, the light may flicker.

mxc400p_us_saf.book 10 ページ２００９年１０月５日　月曜日　午後１時５３分

SUPPLIES

Standard supplies for this product that can be replaced by the user include

paper, toner cartridges, and staple cartridges for the finisher.

Be sure to use only SHARP-specified products for the toner cartridges, finisher

staple cartridge, and transparency film.

Storage of supplies

Proper storage

1. Store the supplies in a location that is:

• clean and dry

• at normal temperature with minimal temperature fluctuations

• not exposed to direct sunlight

2. Store paper in the wrapper and lying flat.

3. Paper stored in packages standing up or out of the wrapper may curl or

become damp, resulting in paper misfeeds.

Storing toner cartridges

Store the box that contains the toner cartridge horizontally; do not store it

standing up. If the toner cartridge is stored standing up, the toner may solidify

inside the cartridge.

Store the toner in a location that is cooler than 104°F (40°C). Storage in a hot

location may cause the toner in the cartridge to solidify.

Staple cartridge

The finisher requires the following staple cartridge:

MX-SCX1 (for finisher)

Approx. 5000 per cartridge x 3 cartridges

Supply of spare parts and consumables

The supply of spare parts for repair of the machine is guaranteed for at least 7

years following the termination of production. Spare parts are those parts of the

machine which may break down within the scope of the ordinary use of the

product, whereas those parts which normally exceed the life of the product are

not to be considered as spare parts. Consumables too, are available for 7 years

following the termination of production.

For best printing results, be sure to use only Sharp Genuine

Supplies which are designed, engineered, and tested to

maximize the life and performance of Sharp products. Look for

the Genuine Supplies label on the toner package.

GENUINE SUPPLIES

mxc400p_us_saf.book 11 ページ２００９年１０月５日　月曜日　午後１時５３分

SPECIFICATIONS

Machine specifications

*1 When the machine is used as a PostScript printer.

*2 When the XPS expansion kit is installed.

*3 Barcode font kit is required.

*4 Supported operating systems are Windows 2000 / Server 2003 / XP / Vista /

Server 2008 / 7.

*5 To install the XPS expansion kit, an expansion memory board is required.

Name

Digital Full Color Printer

MX-C400P

Type

Desktop

Display

4.3 inch color LCD

Photoconductive type

OPC drum

Printing method

Electrophotographic system (laser)

Developer system

Dry-type two-component magnetic brush development

Fusing system

Heat rollers

Printing resolution

600 x 600 dpi / 1200 x 1200 dpi

Printing gradation

Equivalent to 256 levels

Printer driver type

PCL5c, PCL6, PostScript 3 compatible*

, XPS*

Supported protocols

TCP/IP, IPX/SPX, NetBEUI, EtherTalk

Supported client PC

operating systems

See "VERIFYING SYSTEM REQUIREMENTS" in the

Software Setup Guide.

Fonts

PCL5c,

PCL6

80 European fonts, 28 barcode fonts*

1 bitmap font

PostScript 3

compatible*

136 European fonts

Interface port

LAN connectivity: 10Base-T / 100Base-TX / 1000Base-T

USB connectivity: Supports USB 2.0 (Hi speed)*

Memory

Standard

system

memory

1GB

Expansion

memory

1GB*

Print area

Entire page excluding margin of 11/64" (4.2 mm) at each

edge. The actual print area may vary depending on the

printer driver and the software application.

mxc400p_us_saf.book 12 ページ２００９年１０月５日　月曜日　午後１時５３分

SPECIFICATIONS

Machine specifications (Continued)

* First print out time is the time from when the machine starts printing operation until the

print is output. It is measured in full ready condition with fuser at operating temperature

and actual time may vary based on environment conditions.

Warm-up time

90 seconds or less (This may vary depending on the

ambient conditions.)

First-print time*

Color print time: 8.9 seconds or less

Black and white print time: 8.0 seconds or less

(Portrait feeding of 8-1/2" x 11" (A4) sheets may vary

depending on the state of the machine.)

Tray 1

Paper sizes: 8-1/2" x 14", 8-1/2" x 13-1/2",

8-1/2" x 13-2/5", 8-1/2" x 13",

8-1/2" x 11", 7-1/4" x 10-1/2",

5-1/2" x 8-1/2", A4, B5, A5, 16K

(Includes automatic paper size

detection function.)

Paper weight: Plain paper (16 lbs. to 28 lbs. (60 g/m

to 105 g/m

))

Paper capacity: Plain paper (21 lbs. (80 g/m

)) 500

sheets

Paper types: SHARP-recommended plain paper,

recycled paper and colored paper

Bypass tray

Paper sizes: 8-1/2" x 14", 8-1/2" x 13-1/2",

8-1/2" x 13-2/5", 8-1/2" x 13", 8-1/2" x 11",

7-1/4" x 10-1/2", 5-1/2" x 8-1/2",

envelopes, A4, B5, A5, 16K (Includes

automatic paper size detection function.

Paper sizes from 3-15/16" x 5-53/64"

(100 mm x 148 mm) to 8-33/64" x 14-1/64"

(216 mm x 356 mm) can be entered.)

Paper weights:

Thin paper (15 lbs. to 16 lbs. (55 g/m

to 59 g/m

)), plain

paper (16 lbs. to 28 lbs. (60 g/m

to 105 g/m

)), heavy

paper (28 lbs. bond to 110 lbs. index (106 g/m

209 g/m

))

Paper capacity: Standard paper 100 sheets

Paper types:

SHARP-recommended plain paper, recycled paper,

colored paper, heavy paper, thin paper, transparency

film, and envelopes (Monarch, Com-10, DL, C5)

mxc400p_us_saf_02.fm 13 ページ２００９年１０月９日　金曜日　午後２時４９分

SPECIFICATIONS

Machine specifications (Continued)

* Type A connectors are located on the front and back right of the machine (two

connectors); however, the connectors cannot be used simultaneously. The connector

on the back of the machine is not initially available for use. If you wish to use the

connector, contact your service assistance.

Duplex module

Paper sizes: 8-1/2" x 14",

8-1/2" x 13-1/2",

8-1/2" x 13-2/5",

8-1/2" x 13", 8-1/2" x 11",

5-1/2" x 8-1/2", A4, B5, A5, 16K

Paper weight: Plain paper (16 lbs. to 28 lbs. (60 g/m

105 g/m

))

Paper types:SHARP-recommended plain paper,

recycled paper, and colored paper

Output tray (Center tray)

Output method: Face-down output

Output capacity: 250 sheets (using SHARP-recommended

8-1/2" x 11" or A4 paper)

(The maximum number of sheets that can be held varies

depending on ambient conditions in the installation

location, the type of paper, and the storage conditions of

the paper.)

Tray full sensor: Yes

Interface port

LAN connectivity: 10Base-T / 100Base-TX /

1000Base-T

USB connectivity: Type A connector supports USB 2.0

(Hi speed)*

Compatibility requirements of USB 2.0

Memory Capacity: Max. 32 GB

Disk Format: FAT32 only

Type B connector supports USB 2.0

(Hi speed)

mxc400p_us_saf.book 14 ページ２００９年１０月５日　月曜日　午後１時５３分

SPECIFICATIONS

Machine specifications (Continued)

Required power supply

AC 120 V ±10% 60 Hz

Power consumption

1.44 kW

Dimensions

22-3/64" (W) x 17-1/4" (D) x 24-1/64" (H)

(560 mm (W) x 438 mm (D) x 610 mm (H))

Weight

Approx. 97.0 lbs. (44 kg)

Overall dimensions

34-11/64" (W) x 17-1/4" (D) (868 mm (W) x 438 mm (D))

(when bypass tray is extended)

mxc400p_us_saf_02.fm 15 ページ２００９年１０月９日　金曜日　午前１０時３０分

SPECIFICATIONS

Continuous printing speeds*

* Print speed during output of the second print and following prints when performing

continuous one-sided printing of the same page (excluding offset output) using plain

one-sided paper from a tray other than the bypass tray.

Print ratio

100% / Reduced / Enlarged

Print mode

Color B/W

8-1/2" x 11", 7-1/2" x 10"-1/2"

40 pages/min. 40 pages/min.

, B5, 16K

38 pages/min. 38 pages/min.

Ambient environment

85%

(Humidity)

(Temperature)

60%

20%

54˚F

(10˚C)

86˚F

(30˚C)

91˚F

(35˚C)

mxc400p_us_saf.book 16 ページ２００９年１０月５日　月曜日　午後１時５３分

SPECIFICATIONS

Acoustic noise emission (measurement according to

ISO7779)

Chemical emission (measured according to RALUZ122:

Edition Jun. 2006)

Sound power level LwA

Printing mode (continuous printing)

Color: 6.8 B

B/W: 6.7 B

Standby mode

4.8 B

Sound pressure level LpA (actual measurement)

Printing mode

Bystander

positions

Color: 54 dB (A)

B/W: 53 dB (A)

Operator

positions

Color: 58 dB (A)

B/W: 58 dB (A)

Standby mode

Bystander

positions

35 dB (A)

Operator

positions

37 dB (A)

Ozone

1.5 mg/h or less

Dust

4.0 mg/h or less

Styrene

1.0 mg/h or less

Benzene

less than 0.05 mg/h

TVOC (Printing)

10 mg/h or less

TVOC (Pre-Operating)

2 mg/h or less

mxc400p_us_saf_02.fm 17 ページ２００９年１０月７日　水曜日　午後１時４６分

SPECIFICATIONS

500-sheet paper feed unit specifications

* Only MX-CSX1 can be used.

Model

MX-CSX1 (tray 2) MX-CSX2 (tray 3, tray 4)

Paper sizes

8-1/2" x 14", 8-1/2" x 13-1/2", 8-1/2" x 13-2/5", 8-1/2" x 13",

8-1/2" x 11", 7-1/4" x 10-1/2", 5-1/2" x 8-1/2"*, A4, B5, A5*, 16K

Paper weight

Plain paper (16 lbs. to 28 lbs. (60 g/m

to 105 g/m

))

Paper capacity

500 sheets (21 lbs. (80 g/m

)) x 1 tray

Paper types

SHARP-recommended plain paper, recycled paper, and colored

paper

Automatic paper

size detection

When "Auto-Inch" detection is selected:

8-1/2" x 14", 8-1/2" x 11", 7-1/4" x 10-1/2", 5-1/2" x 8-1/2"*

When "Auto-AB" detection is selected:

A4, B5, A5*, 216 mm x 330 mm (8-1/2" x 13")

Power supply

Supplied from the machine

Dimensions

21-1/16" (W) x 17-1/4" (D) x 4-13/32" (H)

(535 mm (W) x 438 mm (D) x 112 mm (H))

(not including adjuster)

21-1/16" (W) x 17-1/4" (D) x 4-21/64" (H)

(535 mm (W) x 438 mm (D) x 110 mm (H))

(not including adjuster)

Weight

Approx. 15.0 lbs. (6.8 kg) Approx. 12.3 lbs. (5.6 kg)

mxc400p_us_saf.book 18 ページ２００９年１０月５日　月曜日　午後１時５３分

Page is loading ...

Sharp MX-C400P Owner's manual

Brand: Sharp

Model: MX-C400P

Category: Copiers

Type: Owner's manual

Download PDF

report

Sharp MX-C400P Owner's manual

Sharp MX-C400P Owner's manual

Related papers

Other documents