Contec CNET1000-1T-PE NEW Reference guide

Brand: Contec

Model: CNET1000-1T-PE NEW

Type: Reference guide

Reference Manual

CONTENTS

PCI Express Ethernet Network Card (LAN Board) 1- port

CNET1000-1T-PE

Introduction .................................................................. 4

Safety Precautions .................................................... 10

Setup ............................................................................. 16

Installation ................................................................... 23

Appendix ...................................................................... 25

Customer Support and Inquiry ............................ 28

Table of Contents

Introduction ...................................................................... 4

1. Related Manuals ......................................................................................................................................................5

2. About the Product ..................................................................................................................................................6

3. Features ......................................................................................................................................................................7

4. Included Items .........................................................................................................................................................8

5. Support Software ....................................................................................................................................................9

Safety Precautions ......................................................... 10

1. Safety Information ............................................................................................................................................... 11

2. Handling Precautions ......................................................................................................................................... 12

1. FCC PART 15 Class A Notice ...................................................................................................................... 14

2. EN55032Class A Notice .............................................................................................................................. 14

3. VCCI Class A .................................................................................................................................................... 14

3. Environment ........................................................................................................................................................... 15

4. Inspection ............................................................................................................................................................... 15

5. Storage ..................................................................................................................................................................... 15

6. Disposal ................................................................................................................................................................... 15

Setup ............................................................................... 16

1. What is Setup? ...................................................................................................................................................... 17

1. Driver Software Installation(Windows) ................................................................................................. 17

2. Driver Software Installation(Linux) ......................................................................................................... 17

1. Hardware Setting ................................................................................................................................................. 19

1. Nomenclature of Product Components ............................................................................................... 19

2. Ethernet Port ................................................................................................................................................... 19

3. Replacing the Bracket .................................................................................................................................. 20

2. Hardware installation ......................................................................................................................................... 21

1. Plugging the Board ...................................................................................................................................... 21

2. Turning on the PC ......................................................................................................................................... 22

Installation ...................................................................... 23

1. Connecting to Network ..................................................................................................................................... 24

1. Network Cable ................................................................................................................................................ 24

Appendix ........................................................................ 25

1. Hardware Specifications.................................................................................................................................... 26

2. Physical Dimensions ........................................................................................................................................... 27

Table of Contents

Customer Support and Inquiry ..................................... 28

1. Services .................................................................................................................................................................... 29

Introduction

This section provides necessary information of the product

such as the outline, bundled items and manuals before

actual use.

—

Introduction

—

CNET1000-1T-PE Reference Manual

1. Related Manuals

The manuals related to the product are listed below.

Read them as necessary along with this document.

 Must Read the Following.

Name

Purpose

Contents

How to get

Please read the

following

Must read this after

opening the package.

This introduces related

materials that are made

available on the CONTEC

website, such as those for the

included items, manuals, and

software.

Included in the package

(Printed matter)

Reference Manual

(This document)

Read this when operating

the product.

This describes the hardware

aspects such as functions and

settings.

Download from

the Contec

website (PDF)

 Download Manuals

Download the manuals accordingly from the following URL.

Download

https://www.contec.com/download/

—

Introduction

—

CNET1000-1T-PE Reference Manual

2. About the Product

This product is a 1-port a PCI Express bus-compliant Ethernet Network Card(LAN Board) which

conforms to IEEE802.3ab (1000BASE-T) /IEEE802.3u (100BASE-TX) /IEEE802.3 (10BASE-T) standard.

This product supports a Low-Profile size slot and if replaced with the supplied bracket, supports a

standard size slot, too.

Windows/Linux driver is supported with this product.

—

Introduction

—

CNET1000-1T-PE Reference Manual

3. Features

 PCI Express bus-compliant Ethernet Network Card(LAN

Board) which conforms to IEEE802.3ab (1000BASE-T)

This product is a 1-port a PCI Express bus-compliant Ethernet Network Card(LAN Board) which conforms to IEEE802.3ab (1000BASE-T)

/IEEE802.3u (100BASE-TX) /IEEE802.3 (10BASE-T) standard.

 Low-Profile size slot and Standard size slot

This product supports a Low-Profile size slot and if replaced with the supplied bracket, supports a standard size slot, too.

 Operated in the temperature between -40 °C and

+75 °C.

Operated in the temperature between -40 °C and +75 °C.

 Windows/Linux compatible driver

Download from the CONTEC website.

—

Introduction

—

CNET1000-1T-PE Reference Manual

4. Included Items

The product consists of the items listed below.

Check, with the following list, that your package is complete.

If you discover damaged or missing items, contact your retailer.

Product…1

Standard size Bracket...1

Common Guide...1

—

Introduction

—

CNET1000-1T-PE Reference Manual

5. Support Software

You can use CONTEC support software according to your purpose and development environment.

For more details on the supported OS, applicable languages, or to download the latest version of

software, visit the CONTEC Web site.

Name

Contents

How to get

Windows Version

The Windows driver for installer is provided.

Download from the

CONTEC website

Linux Version

This is the Linux version.

Download from the

CONTEC website

Download the files from the following URL.

Download

https://www.contec.com/download/

Safety Precautions

Understand the following definitions and precautions to

use the product safely.

Never fail to read them before using the product.

—

Safety Precautions

—

CNET1000-1T-PE Reference Manual

1. Safety Information

This document provides safety information using the following symbols to prevent accidents

resulting in injury or death and the destruction of equipment and resources.

Understand the meanings of these labels to operate the equipment safely.

DANGER

Signal word used to indicate an imminently hazardous situation which,

if not avoided, will result in death or serious injury.

WARNING

Signal word used to indicate a potentially hazardous situation which,

if not avoided, could result in death or serious injury.

CAUTION

Signal word used to indicate a potentially hazardous situation which,

if not avoided, could result in minor or moderate injury.

—

Safety Precautions

—

CNET1000-1T-PE Reference Manual

2. Handling Precautions

WARNING

 Do not modify the product.

 Do not use the product in locations exposed to a flammable or corrosive gas. It may cause

explosion, fire, electrical shock, or malfunction.

 If the equipment is used in a manner not specified by the manufacturer, the protection

provided by the equipment may be impaired.

 This product is not intended for use in aerospace, space, nuclear power, medical equipment,

or other applications that require a very high level of reliability. Do not use the product in

such applications.

 If using this product in applications where safety is critical such as in railways, automotive, or

disaster prevention or security systems, please contact your retailer.

CAUTION

 Do not use or store the product in a location exposed to extremely high or low temperature

or susceptible to a rapid temperature changes.

Example: - Exposure to direct sun - In the vicinity of a heat source

 Do not use the product in extremely humid or dusty locations. It is extremely dangerous to

use this product with its interior penetrated by water or any other fluid or conductive dust.

 Avoid using or storing the product in locations subject to shock or vibration that exceeds

range of specification.

 When transporting the product, take suitable measures to avoid applying shock or vibration

directly to the product.

Impact resistance: 15G (11ms) below.

 Avoid installing in the place where ventilation of the product may compromise. Insufficient

aeration could heat up the product and lead to malfunctions or damages.

 The link speed value (e.g., 1000Mbps) of the transmission rate used in the Manual (this

document) is the theoretical maximum value of the Ethernet standard and do not indicate the

actual data transmission speed.

 The frame loss could occur depending on the connection destination or installed environment

 Do not strike or bend this product. Otherwise, this product may malfunction, overheat, cause a

failure or breakage.

 This product contains precision electronic elements and must not be used in locations subject

to physical shock or strong vibration. Otherwise, the board may malfunction, overheat, or

cause a failure.

 As this product contains components that are designed to operate at high temperature,

please do not touch this product when it is in use.

—

Safety Precautions

—

CNET1000-1T-PE Reference Manual

 Do not use or store the equipment in a place subject to direct sunlight or near a heating

device, such as a stove. And do not use or store the product near equipment generating a

strong magnetic field or radio waves. They may cause the malfunction, heat generation,

fault, or damage.

 Do not use the product in the vicinity of devices that generate strong magnetic force or noise.

Such products will cause the product to malfunction (stop, reboot).

 Do not use or store the product in the presence of chemicals.

 Do not touch this product's metal plated terminals (edge connector) with your hands.

Otherwise, this product may malfunction, overheat, or cause a failure. If the terminals are

touched by someone's hands, clean the terminals with industrial alcohol.

 When placing importance on line-noise resistance, use shielded cables to connect to periphery

devices.

 As this product contains components that are designed to operate at high temperature, please

do not touch this product when it is in use.

 Do not install this product to the expansion slot and do not plug or unplug the cables which

are connected to this product while the PC or expansion unit is still turned on. Otherwise, this

product may malfunction, overheat, or cause a failure. Be sure that the personal computer

power is turned off.

 Do not touch the external connector when the power is on. Otherwise, this may malfunction,

cause a failure due to static electricity.

 When connecting cables, first check the shapes of connectors, and then insert them in the

correct orientation. After they are connected, do not put too much load on the connected part.

Doing so may result in poor contact or damage to this product and the connected part.

 Make sure that your PC or expansion unit can supply ample power to all the products installed.

Insufficiently energized products could malfunction, overheat, or cause a failure.

 Do not touch the product or connectors with a wet hand to avoid electric shock.

 The specifications of the product are subject to change without notice for enhancement and

quality improvement. Even when using the product continuously, be sure to read the manual

in the CONTEC's website and understand the contents.

 Do not modify the product. CONTEC will bear no responsibility for any problems, etc.,

resulting from modifying this product.

 When the product is used in a place that is affected by overcurrent or overvoltage (lightning

surge), select appropriate surge protection device for all the route (Power line, signal line,

earth, etc.). Consult with the specialist regarding selecting, purchasing, and setting the surge

protection device.

 When disposing of the product, follow the disposal procedures stipulated under the relevant

laws and municipal ordinances.

 Regardless of the foregoing statements, CONTEC is not liable for any damages whatsoever

(Including damages for loss of business profits) arising out of the use or inability to use the

CONTEC product or the information contained herein.

—

Safety Precautions

—

CNET1000-1T-PE Reference Manual

1. FCC PART 15 Class A Notice

NOTE

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used

in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

FCC WARNING

Changes or modifications not expressly approved by the party responsible for compliance could void

the user's authority to operate the equipment.

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received,

including interference that may cause undesired operation.

2. EN55032Class A Notice

Warning:

Operation of this equipment in a residential environment could cause radio interference.

3. VCCI Class A

この装置は、クラスＡ機器です。この装置を住宅環境で使用すると電波妨害を引き起こすことがあります。

この場合には使用者が適切な対策を講ずるよう要求されることがあります。

VCCI-A

CAUTION

The product standard applies to the main body only.

—

Safety Precautions

—

CNET1000-1T-PE Reference Manual

3. Environment

Use this product in the following environment. If used in an unauthorized environment, the board

may overheat, malfunction, or cause a failure.

Operating temperature

-40 - +75ºC

Humidity

10 - 90%RH (No condensation)

Corrosive gases

None

Floating dust particles

Not to be excessive

4. Inspection

Inspect the product periodically to use it safely.

5. Storage

When storing this product, keep it in its original packing form.

 Put this product in the storage bag.

 Wrap it in the packing material, and then put it in the box.

 Store the package at room temperature at a place free from direct sunlight, moisture, shock,

vibration, magnetism, and static electricity.

6. Disposal

When disposing of the product, follow the disposal procedures stipulated under the relevant laws

and municipal ordinances.

Setup

This section describes how to set up the product.

—

Setup

—

CNET1000-1T-PE Reference Manual

1. What is Setup?

Setup means a series of steps to take before the product can be used.

Different steps are required for driver software and hardware.

The setup procedure varies with the OS or driver software used.

This section shows how to install the driver software.

Install the device driver before connecting this product to a PC.

1. Driver Software Installation(Windows)

1 Download the Drive from CONTEC website.(Windows)

2 Expand the downloaded file.

3 Execute the installer in the expanded folder.

¥Wired_driver_xx.x_x64¥Setup.exe

* xx.x is version number.

2. Driver Software Installation(Linux)

1 Download the Drive from CONTEC website. (Linux)

2 Expand the downloaded file.

3 Execute the installer in the expanded folder.

tar zxf igb-<x.x.x>.tar.gz

* xx.x is version number.

4 Move to the src directory in the expanded directory.

cd igb-<x.x.x>.tar.gz/src

Use the following commands to install the compile environment.

MIRACLE LINUX 9 example

Connect to the Internet, and then enter the following commands.

sudo dnf install make gcc

sudo dnf install kernel-devel-$(uname -r)

—

Setup

—

CNET1000-1T-PE Reference Manual

Ubuntu 22.04.2 LTS example

Connect to the Internet, and then enter the following commands.

sudo apt update

sudo apt install build-essential manpages-dev

RedHat Enterprise Linux 9.1 example

1. Connect the RedHat Enterprise Linux 9.1 installation media to the PC.

2. Use the lsblk command to check where the installation media is mounted.

(As an example, the media is mounted on “/run/media/contec/RHEL-9-1-0-BaseOS-x86_64.”)

3. Use a text editor to create and edit the following file.

sudo nano /etc/yum.repos.d/dvd.repo

------ Contents of dvd.repo ------

[BaseOS]

name=BaseOS RHEL9_1

metadata_expire=-1

gpgcheck=1

enabled=1

baseurl=file:///run/media/contec/RHEL-9-1-0-BaseOS-x86_64/BaseOS

gpgkey=file:///etc/pki/rpm-gpg/RPM-GPG-KEY-redhat-release

[Appstream]

name=Appstream RHEL9_1

metadata_expire=-1

gpgcheck=1

enabled=1

baseurl=file:///run/media/contec/RHEL-9-1-0-BaseOS-x86_64/AppStream/

gpgkey=file:///etc/pki/rpm-gpg/RPM-GPG-KEY-redhat-release

----------------------------

4. Use the following commands to install the compile environment.

sudo dnf group install 'Development Tools'

5 Use the make command to install the driver.

sudo make install

—

Setup

—

CNET1000-1T-PE Reference Manual

1. Hardware Setting

This section describes how to set up the product and how to connect it to a PC.

1. Nomenclature of Product Components

Component names of the product are shown in the figure below.

No.

Name

Ethernet Port

2. Ethernet Port

Color and Description

LED

Color

Display

Description

Speed

Orange/

Green

It is connected at 1Gbps.

It is connected at 100Mbps.

OFF

It is connected at 10Mbps, or it is left unconnected.

Link/Act

Yellow

It is connected.

Flashing

Data are sent or received.

OFF

It is not connected.

—

Setup

—

CNET1000-1T-PE Reference Manual

3. Replacing the Bracket

This board is shipped with a Low Profile size bracket mounted. To plug the board into a standard size

slot, replace the bracket with the bundled standard size bracket. The replacing method is as follows :

Page is loading ...

Contec CNET1000-1T-PE NEW Reference guide

Contec CNET1000-1T-PE NEW Reference guide

Contec CNET1000-1T-PE NEW Reference guide

Related papers

Other documents