The Danfoss TMTHW orbital motor offers robust bearing design, exceptional sealing, and high-pressure rating for demanding applications. Its strength and efficiency make it ideal for construction, agricultural, material handling, forestry, and marine equipment, among other heavy-duty machinery.
The Danfoss TMTHW orbital motor offers robust bearing design, exceptional sealing, and high-pressure rating for demanding applications. Its strength and efficiency make it ideal for construction, agricultural, material handling, forestry, and marine equipment, among other heavy-duty machinery.
Revision history Table of revisions
Date Changed Rev
November 2015 Code number corrected 0101
April 2015 Converted to Danfoss layout BA
August 2013 First version AA
Technical Information TMTHW Orbital Motors
2 L1327341 en-US • Rev 0101 • November 2015
A wide range of Orbital Motors
Characteristic, features and application areas of Orbital Motors....................................................................................4
Characteristic features of Danfoss Orbital Motors.......................................................................................................... 4
Technical features of Danfoss Orbital Motor.....................................................................................................................4
The Danfoss Orbital Motors are used in the following application areas:..............................................................5
Survey of literature with technical data on Danfoss Orbital Motors..............................................................................5
Introduction the Orbital Motor Series
T-Series – The Highest Torque.....................................................................................................................................................6
O-Series – The Flexible Choice.....................................................................................................................................................6
V-Series – The Core Solution........................................................................................................................................................ 6
TMTHW features................................................................................................................................................................................6
Speed, torque and output
TMTHW speed, torque and output............................................................................................................................................ 7
Versions and code numbers
TMTHW version and code numbers.......................................................................................................................................... 8
Technical data
Technical data for TMTHW............................................................................................................................................................9
Maximum permissible shaft seal pressure.............................................................................................................................. 9
Pressure drop in motor................................................................................................................................................................10
Direction of shaft ...........................................................................................................................................................................11
Permissible shaft load for TMTHW...........................................................................................................................................11
Function diagrams
TMTHW 315......................................................................................................................................................................................12
TMTHW 400......................................................................................................................................................................................13
TMTHW 500......................................................................................................................................................................................13
TMTHW 630......................................................................................................................................................................................14
TMTHW 800......................................................................................................................................................................................14
Technical data
Port thread versions......................................................................................................................................................................15
Manifold............................................................................................................................................................................................ 15
Dimensions
Wheel flange-spigot diameter Ø 180 mm - BC Ø 210 mm..............................................................................................16
Wheel flange-spigot diameter Ø 223.9 mm - BC Ø 265 mm..........................................................................................17
Technical Information
TMTHW Orbital Motors
Contents
L1327341 en-US • Rev 0101 • November 2015 3
Characteristic, features and application areas of Orbital Motors
Danfoss is a world leader within production of low speed orbital motors with high torque. We can offer
more than 3,000 different orbital motors, categorised in types, variants and sizes (including different shaft
versions).
The motors vary in size (rated displacement) from 8 cm³ [0.50 in³] to 800 cm³ [48.9 in³] per revolution.
Speeds range up to approximate 2,500 min
-1
(rpm) for the smallest type and up to approximate 600 min
-1
(rpm) for the largest type.
Maximum operating torques vary from 13 N•m [115 lbf•in] to 2,700 N•m [24,000 lbf•in] (peak) and
maximum outputs are from 2.0 kW [2.7 hp] to 70 kW [95 hp].
Characteristic features of Danfoss Orbital Motors
•
Smooth running over the entire speed range
•
Constant operating torque over a wide speed range
•
High starting torque
•
High return pressure without the use of drain line (High pressure shaft seal)
•
High efficiency
•
Long life under extreme operating conditions
•
Robust and compact design
•
High radial and axial bearing capacity
•
For applications in both open and closed loop hydraulic systems
•
Suitable for a wide variety of hydraulics fluids
Technical features of Danfoss Orbital Motor
The programme is characterised by technical features appealing to a large number of applications and a
part of the programme is characterised by motors that can be adapted to a given application. Adaptions
comprise the following variants among others:
Technical Information
TMTHW Orbital Motors
A wide range of Orbital Motors
4 L1327341 en-US • Rev 0101 • November 2015
•
Motors with corrosion resistant parts
•
Wheel motors with recessed mounting flange
•
OMP, OMR- motors with needle bearing
•
OMR motor in low leakage version
•
OMR motors in a super low leakage version
•
Short motors without bearings
•
Ultra short motors
•
Motors with integrated positive holding brake
•
Motors with integrated negative holding brake
•
Motors with integrated flushing valve
•
Motors with speed sensor
•
Motors with tacho connection
•
All motors are available with black finish paint
The Danfoss Orbital Motors are used in the following application areas:
•
Construction equipment
•
Agricultural equipment
•
Material handling & Lifting equipment
•
Forestry equipment
•
Lawn and turf equipment
•
Special purpose
•
Machine tools and stationary equipment
•
Marine equipment
Survey of literature with technical data on Danfoss Orbital Motors
Detailed data on all Danfoss Orbital Motors can be found in our motor catalogue, which is divided into
more individual subcatalogues:
•
General information on Danfoss Orbital Motors: function, use, selection of orbital motor, hydraulic
systems, etc.
•
Technical data on small motors: OML and OMM
•
Technical data on medium sized motors: OMP, OMR, OMH
•
Technical data on medium sized motors: DH and DS
•
Technical data on medium sized motors: OMEW
•
Technical data on medium sized motors: VMP
•
Technical data on medium sized motors: VMR
•
Technical data on large motors: OMS, OMT and OMV
•
Technical data on large motors: TMK
•
Technical data on large motors: TMT
•
Technical data on large motors: TMTHW
•
Technical data on large motors: TMVW
A general survey brochure on Danfoss Orbital Motors gives a quick motor reference based on power,
torque, speed and capabilities.
Technical Information
TMTHW Orbital Motors
A wide range of Orbital Motors
L1327341 en-US • Rev 0101 • November 2015 5
By introducing the TMTHW, Danfoss is introducing the first Orbital Motor of a new Series. In order to meet
the demands for motors that have the right duty cycle and efficiency capabilities for a given function.
Danfoss now has 3 Orbital Motor Series:
T-Series – The Highest Torque
Leading performance with a long lifetime makes light work of the heaviest duties. Offering pressure
capability up to 350 bar [5076 psi] and high starting torque, the T-Series is the energy-efficient choice for
the toughest working environments.
O-Series – The Flexible Choice
The O-Series is flexible beyond compare. Delivering premium power across the board, these motors
cover small to large, medium to heavy-duty needs with pressure capability up to 275 bar [3990 psi].
Robust, reliable and designed to fulfill the latest emissions standards.
V-Series – The Core Solution
The V-Series is your quality benchmark in the medium duty market. Based on proven technology, these
reliable motors will reduce your overall system costs while adding value to your machine. Perfect for
many tasks.
TMTHW features
•
Robust bearing design
•
Not sensitive towards return pressure
•
Extra patented sealing design
•
High pressure rating
•
Excellent performance / weight
•
Designed based on decades of experience with orbital motor-technology
Technical Information
TMTHW Orbital Motors
Introduction the Orbital Motor Series
6 L1327341 en-US • Rev 0101 • November 2015
The following bar diagrams, are useful for a quick selection of relevant motor size for the application. The
final motor size can be determined by using the Function diagrams on page 12.
The function diagrams are based on actual tests on a representative number of motors from our
production. The diagrams apply to a return pressure between 5 and 10 bar [75 and 150 psi] when using
mineral based hydraulic oil with a viscosity of 35 mm
2
/s [165 SUS] and a temperature of 50°C [120°F]. For
further explanation concerning how to read and use the function diagrams, please consult the paragraph
"Selection of motor size" in the technical information "General" 520L0232.
TMTHW speed, torque and output
The bar diagrams shown are useful for a quick selection of relevant motor size for the application.
1. Intermittend values
2. Continuous values
Maximum speed
P301 810
1
2
min
-1
(rpm)
0
100
200
300
400
500
600
315 400 500 630 800
Maximum torque
P301 811
1
2
lbf•in Nm
35 000
30 000
25 000
20 000
15 000
10 000
5 000
0
0
500
1000
1500
2000
2500
3000
3500
4000
315 400 500 630 800
Maximum output
P301 812
1
2
hp kW
90
80
70
60
50
40
30
20
10
0
0
10
20
30
40
50
60
70
315 400 500 630 800
Technical Information
TMTHW Orbital Motors
Speed, torque and output
L1327341 en-US • Rev 0101 • November 2015 7
TMTHW version and code numbers
TMTHW standard motor
Mounting flange: Wheel
Spigot
diamer
Ø180 mm [7.09 in]
Bolt circle
diameter
Ø210 mm [8.27 in]
Shaft Port size Port Style Drain Port
size
Standard
shaft seal
Metric
version
Painted
black
Check valve Main type
designation
Conf. code
Thread hole
Fl.
G 3/4 Side port G 1/4 X X X No TMTHW A1
Code numbers TMTHW wheel flange
Conf. code Displacement
315 400 500 630 800
A1 11137330 11137331 11137342 11053388 11125392
Mounting flange: Wheel
Spigot
diamer
Ø224 mm [8.82 in]
Bolt circle
diameter
Ø265 mm [10.4 in]
Shaft Port size Port Style Drain port
size
Standard
shaft seal
Metric
version
Painted
black
Check valve Main type
designation
Conf. code
Thread hole
Fl.
G 3/4 Side port G 1/4 X X X No TMTHW B1
Code numbers TMTHW wheel flange
Conf. code Displacement
315 400 500 630 800
B1 - 11089435 11089438 11089439 11089440
Technical Information TMTHW Orbital Motors
Versions and code numbers
8 L1327341 en-US • Rev 0101 • November 2015
Technical data for TMTHW
Type TMTHW TMTHW TMTHW TMTHW TMTHW
Motor size 315 400 500 630 800
Geometric
displacement
cm
3
[in
3
]
314.9
[19.2]
393.1
[24.0]
495
[32.2]
630.7
[38.5]
802.2
[49.0]
Maximum speed min
-1
[rpm]
cont.
490 450 400 315 240
int.
1)
580 590 480 370 290
Maximum torque N•m
[lbf•in]
cont.
1300
[11 500]
1690
[14 960]
2200
[19 470]
2510
[22 215]
2650
[23 450]
int.
1)
1510
[13 365]
1950
[17 260]
2550
[22 570]
3220
[28 500]
3510
[31 065]
Maximum
output
kW
[hp]
cont.
50 [67] 55 [74] 55 [74] 50 [67] 50 [67]
int.
1)
55 [74] 60 [80] 65 [87] 60 [80] 60 [80]
Maximum
pressure drop
bar
[psi]
cont.
300 [4350] 300 [4350] 300 [4350] 275 [3990] 225 [3260]
int.
1)
350 [5075] 350 [5075] 350 [5075] 350 [5075] 300 [4350]
Maximum oil
flow
l/min
[US gal/min]
cont.
150 [39.6] 180 [47.6] 200 [52.8] 200 [52.8] 200 [52.8]
int.
1)
180 [47.6] 240 [63.4] 240 [63.4] 240 [63.4] 240 [63.4]
Max. starting
pressure with
unloaded shaft
bar
[psi]
6 [87] 6 [87] 6 [87] 6 [87] 5 [72]
Minimum
starting torque
N•m
[lbf•in]
at max. press.
drop cont.:
910
[8055]
1185
[10490]
1540
[13630]
1730
[15310]
1855
[16420]
at max. press.
drop int.
1)
:
1060
[9380]
1365
[12080]
1785
[15800]
2255
[19960]
2460
[21770]
1)
Intermittent operation: the permissible values may occur for max. 10% of every minute
Type Maximum inlet pressure Maximum return pressure
with drain line
TMTHW 315-800 bar
[psi]
Cont.
300 [4350] 140 [2031]
Int.
1)
380 [5510] 175 [2538]
1)
Intermittend operation: the permissible values may occur for max. 10% of every minute
Oil flow in drain line
The table below shows the maximum oil flow in the drain line at a return pressure less than 5-10 bar
[75-150 psi].
Pressure drop Viscosity Oil flow in drain line
bar [psi] mm
2
/s [SUS] l/min [US gal/min]
200 [2900] 20 [100] 2.5 [0.66]
35 [165] 1.5 [0.4]
275 [3990] 20 [100] 4.0 [1.1]
35 [165] 2.5 [0.66]
Maximum permissible shaft seal pressure
TMTHW with standard shaft seal and drain connection. The pressure on shaft seal equals the pressure in
the drain line.
Technical Information
TMTHW Orbital Motors
Technical data
L1327341 en-US • Rev 0101 • November 2015 9
151-1673.10
0 100 200 300 400 500 600 max.
1500
1200
900
600
300
0
100
90
80
70
60
50
40
30
20
10
0
psi bar
P P
min
-1
(rpm)
- - - - Intermittent operation: The permissible values may occur for maximum 10% of every minute.
____ Continuous operation
Drain line should always be used.
Pressure drop in motor
45
40
35
30
25
20
15
10
5
0
250 50 75 100 125 150 175 200
TMTHW Pressure drop in motor
l/min
US gal/min
P301 556
Q
1
2
Q
psi bar
∆p ∆p
650
600
550
500
450
400
350
300
250
200
150
100
50
0
0 5 10 15 20 25 30 35 40 45 50
The curve applies to an unloaded motor shaft and an oil viscosity of 35 mm
2
/s [165 SUS].
1. TMTHW 315
2. TMTHW 400, 500, 630 and 800
Technical Information
TMTHW Orbital Motors
Technical data
10 L1327341 en-US • Rev 0101 • November 2015
Direction of shaft
Permissible shaft load for TMTHW
0
20 000
40 000
60 000
80 000
100 000
120 000
140 000
-20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120
- 0 +
30 000
24 000
18 000
12 000
6 000
0
P
rad.
[lbf]
P
rad.
N
P301 559
mm
[in]
-1.0 -0.5 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
Permissible radial shaft load
The output shaft runs in tapered roller bearings that permit high axial and radial forces.
The permissible radial load on the shaft is shown for an axial load of 0 N as a function of the distance from
the mounting flange to the point of load application.
The curve is based on B10 Bearing life (2000 hours or 12 000 000 shaft revolutions at 100 min
1
) at rated
output torque, when mineral-based hydraulic oil with a sufficient content of anti-wear additives, is used.
Technical Information
TMTHW Orbital Motors
Technical data
L1327341 en-US • Rev 0101 • November 2015 11
Explanation of function diagram use, basis and conditions can be found under Speed and torque Speed
and torque
[blue] Continuous range
[pink] Intermittent range (max. 10% operation every minute)
Intermittent pressure drop and oil flow must not occur simultaneously.
TMTHW 315
0
250
500
750
1000
1250
1500
1750
0
5 000
10 000
15 000
VMP 50
lbf•in
Nm
0 50 100 150 200 250 300 350 400 450 500 550 600
P301 551
min
-1
(rpm)
100 l/min
[26.4 US gal/min]
125 l/min
[33.0 US gal/min]
150 l/min
[39.6 US gal/min]
180 l/min
[47.6 US gal/min]
Q = 10 l/min
[2.6 US gal/min]
20 l/min
[5.3 US gal/min]
40 l/min
[10.6 US gal/min]
60 l/min
[15.9 US gal/min]
80 l/min
[21.1 US gal/min]
325 bar
[4713 psi]
300 bar
[4351 psi]
250 bar
[3625 psi]
275 bar
[3988 psi]
225 bar
[3263 psi]
200 bar
[2900 psi]
120 bar
[1740 psi]
160 bar
[2320 psi]
80 bar
[1160 psi]
∆ p= 350 bar
[5076 psi]
75%
20kW
30kW
40kW
50kW
60kW
75kW
η
t
=80%
η
t
=60%
70%
N=2.5kW
10kW
5kW
40 bar
[580 psi]
Technical Information TMTHW Orbital Motors
Function diagrams
12 L1327341 en-US • Rev 0101 • November 2015
TMTHW 400
0
250
500
750
1000
1250
1500
1750
2000
2250
0
2 000
4 000
6 000
8 000
10 000
12 000
14 000
16 000
18 000
VMP 50
lbf•in
Nm
0 50 100 150 200 250 300 350 400 450 500 550 600
P301 552
min
-1
(rpm)
100 l/min
[26.4 US gal/min]
125 l/min
[33.0 US gal/min]
150 l/min
[39.6 US gal/min]
180 l/min
[47.6 US gal/min]
Q = 10 l/min
[2.6 US gal/min]
20 l/min
[5.3 US gal/min]
40 l/min
[10.6 US gal/min]
60 l/min
[15.9 US gal/min]
80 l/min
[21.1 US gal/min]
325 bar
[4713 psi]
300 bar
[4351 psi]
250 bar
[3625 psi]
275 bar
[3988 psi]
225 bar
[3263 psi]
200 bar
[2900 psi]
120 bar
[1740 psi]
160 bar
[2320 psi]
80 bar
[1160 psi]
75%
20kW
30kW
40kW
50kW
60kW
80%
η
t
=81%
η
t
=60%
70%
N=2.5kW
10kW
5kW
240 l/min
[63.4 US gal/min]
40 bar
[580 psi]
∆ p= 350 bar
[5076 psi]
TMTHW 500
0
0
250
500
750
1000
1250
1500
1750
2000
2250
2500
2750
0
5 000
10 000
15 000
20 000
VMP 50
lbf•in
Nm
0 50 100 150 200 250 300 350 400 450 500
P301 553
min
-1
(rpm)
100 l/min
[26.4 US gal/min]
125 l/min
[33.0 US gal/min]
150 l/min
[39.6 US gal/min]
200 l/min
[52.8 US gal/min]
Q = 10 l/min
[2.6 US gal/min]
20 l/min
[5.3 US gal/min]
40 l/min
[10.6 US gal/min]
60 l/min
[15.9 US gal/min]
80 l/min
[21.1 US gal/min]
325 bar
[4713 psi]
300 bar
[4351 psi]
250 bar
[3625 psi]
275 bar
[3988 psi]
225 bar
[3263 psi]
200 bar
[2900 psi]
120 bar
[1740 psi]
160 bar
[2320 psi]
80 bar
[1160 psi]
80%
20kW
30kW
40kW
50kW
60kW
81%
η
t
=83%
η
t
=60%
70%
75%
N=2.5kW
10kW
5kW
240 l/min
[63.4 US gal/min]
180 l/min
[47.6 US gal/min]
40 bar
[580 psi]
∆ p= 350 bar
[5076 psi]
Technical Information
TMTHW Orbital Motors
Function diagrams
L1327341 en-US • Rev 0101 • November 2015 13
TMTHW 630
0
250
500
750
1000
1250
1500
1750
2000
2250
2500
2750
3000
3250
3500
0
5 000
10 000
15 000
20 000
25 000
30 000
VMP 50
lbf•in
Nm
0 50 100 150 200 250 300 350 400
P301 554
min
-1
(rpm)
100 l/min
[26.4 US gal/min]
125 l/min
[33.0 US gal/min]
150 l/min
[39.6 US gal/min]
200 l/min
[52.8 US gal/min]
Q = 10 l/min
[2.6 US gal/min]
20 l/min
[5.3 US gal/min]
40 l/min
[10.6 US gal/min]
60 l/min
[15.9 US gal/min]
80 l/min
[21.1 US gal/min]
325 bar
[4713 psi]
300 bar
[4351 psi]
250 bar
[3625 psi]
275 bar
[3988 psi]
225 bar
[3263 psi]
200 bar
[2900 psi]
120 bar
[1740 psi]
160 bar
[2320 psi]
80 bar
[1160 psi]
80%
20kW
30kW
40kW
50kW
60kW
81%
η
t
=83%
η
t
=60%
70%
75%
N=2.5kW
10kW
5kW
240 l/min
[63.4 US gal/min]
180 l/min
[47.6 US gal/min]
40 bar
[580 psi]
∆ p= 350 bar
[5076 psi]
TMTHW 800
0
250
500
750
1000
1250
1500
1750
2000
2250
2500
2750
3000
3250
3500
3750
4000
0
5 000
10 000
15 000
20 000
25 000
30 000
35 000
VMP 50
lbf•in
Nm
0 50 100 150 200 250 300
P301 555
min
-1
(rpm)
100 l/min
[26.4 US gal/min]
125 l/min
[33.0 US gal/min]
150 l/min
[39.6 US gal/min]
200 l/min
[52.8 US gal/min]
20 l/min
[5.3 US gal/min]
40 l/min
[10.6 US gal/min]
60 l/min
[15.9 US gal/min]
80 l/min
[21.1 US gal/min]
250 bar
[3625 psi]
275 bar
[3988 psi]
225 bar
[3263 psi]
200 bar
[2900 psi]
120 bar
[1740 psi]
160 bar
[2320 psi]
80 bar
[1160 psi]
80%
20kW
30kW
40kW
50kW
60kW
81%
83%
η
t
=85%
η
t
=60%
70%
75%
N=2.5kW
10kW
5kW
240 l/min
[63.4 US gal/min]
180 l/min
[47.6 US gal/min]
40 bar
[580 psi]
∆ p= 300 bar
[4351 psi]
10 l/min
[2.6 US gal/min]
Technical Information
TMTHW Orbital Motors
Function diagrams
14 L1327341 en-US • Rev 0101 • November 2015
Port thread versions
A
E
P301 561_AE
min. 18 [0.71]
A: G Main port
E: ISO 228/1 – G 3/4
C
G
P301 561_CG
min. 12 [0.47]
C: G Drain port
G: ISO 228/1 – G 1/4
Manifold
L3
15.6[0.64]
15.6[0.64]
15.6[0.64]
15.6[0.64]
14.5[0.57]
7.25[0.29] 11.0[0.43]
19.6[0.77] 19.6[0.77]42[1.65] 42[1.65]
P301 566
L3: Dimentional for given TMTHW-motor see: Dimensions on page 16.
Technical Information TMTHW Orbital Motors
Technical data
L1327341 en-US • Rev 0101 • November 2015 15
Wheel flange-spigot diameter Ø 180 mm - BC Ø 210 mm
5x 72°
Ø140[5.51]
10x Ø14.2[0.56]
max 242.4[9.54]
max 195.4[7.69]
15°
15°
Ø210[8.27]
15°
15°
Ø172[6.77]
Ø92.7[3.65]
Ø92.9[3.66]
max 146[5.75]
Ø180.0 [7.09]
Ø179.8 [7.08]
7[0.28]
12[0.47]
11.7[0.46]
18[0.71]
7.2[0.28]
124.15[4.888]
84[3.31]
L
max
L
1
L
2
L
3
F
C
D
E
P301 565
Not painted
Not painted
C: G 3/4; 17 mm [0.66 in] deep
D: Drain connection G 1/4; 12 mm [0.47 in] deep
E: M10; 17 mm [0.66 in] deep
F: M14 × 1.5
Size
315-800 cm
3
Weight
34-38 kg
Output shaft
F180/5xM14 BC ø140/PD.ø92.8
Mounting flange
Wheel 10x ø14 BC ø210/PD ø180
Technical Information TMTHW Orbital Motors
Dimensions
16 L1327341 en-US • Rev 0101 • November 2015
TMTHW dimensions
Size
315-800 cm
3
L
MAX
L
1
L
2
L
3
Weight
mm [in] mm [in] mm [in] mm [in] kg [lb]
TMTHW 315 135.1 [5.33] 117.1 [4.61] 106.1 [4.18] 91.6 [3.61] 33.7 [74.30]
TMTHW 400 143.3 [5.64] 125.1 [4.93] 114.1 [4.49] 99.6 [3.92] 34.8 [76.72]
TMTHW 500 153.8 [6.06] 135.6 [5.34] 124.6 [4.91] 110.1 [4.33] 35.7 [78.70]
TMTHW 630 167.8 [6.61] 149.6 [5.89] 138.6 [5.46] 124.1 [4.89] 37.2 [82.01]
TMTHW 800 167.8 [6.61] 149.6 [5.89] 138.6 [5.46] 124.1 [4.89] 37.2 [82.01]
Wheel flange-spigot diameter Ø 223.9 mm - BC Ø 265 mm
C
F
E
D
Not painted
Not painted
Ø265.0[10.43]
8xØ17.6[0.69]
max 310.3[9.54]
5.0[0.20]
23.0[0.91]
5.0[0.20]
max 146[5.75]
Ø223.8[8.81]
Ø224.0[8.82]
Ø200[7.87]
Ø129.7[5.16]
Ø129.9[5.11]
138.7[5.46]
16[0.63]
6[0.24]
20°
20°
20°
ø170.0[6.69]
84[3.31]
max 238.0[9.37]
L
max
L
1
L
2
L
3
6x60°
Technical Information TMTHW Orbital Motors
Dimensions
L1327341 en-US • Rev 0101 • November 2015 17
C: G 3/4; 17 mm [0.66 in] deep
D: Drain connection G 1/4; 12 mm [0.47 in] deep
E: M10; 17 mm [0.66 in] deep
F: M16 × 1.5
Size
400-800 cm
3
Weight
42.1-44.5 kg
Output shaft
F200/6xM16 BC ø170/PD.ø130
Mounting flange
Wheel 8x ø17.5 BC ø265/PD ø224
TMTHW dimensions
Size
400-800 cm
3
L
MAX
L
1
L
2
L
3
Weight
mm [in] mm [in] mm [in] mm [in] kg [lb]
TMTHW 400 139 [5.47] 120.8 [4.76] 109.8 [4.32] 95.3 [3.75] 42.1 [92.81]
TMTHW 500 147.6 [5.81] 129.4 [5.09] 118.4 [4.66] 103.9 [4.09] 43.0 [94.80]
TMTHW 630 161.6 [6.36] 143.4 [5.65] 132.4 [5.21] 117.9 [4.64] 44.5 [98.11]
TMTHW 800 161.6 [6.36] 143.4 [5.65] 132.4 [5.21] 117.9 [4.64] 44.5 [98.11]
Technical Information TMTHW Orbital Motors
Dimensions
18 L1327341 en-US • Rev 0101 • November 2015
Technical Information TMTHW Orbital Motors
L1327341 en-US • Rev 0101 • November 2015 19
Danfoss Power Solutions is a global manufacturer and supplier of high-quality hydraulic and
electronic components. We specialize in providing state-of-the-art technology and solutions
that excel in the harsh operating conditions of the mobile off-highway market. Building on
our extensive applications expertise, we work closely with our customers to ensure
exceptional performance for a broad range of off-highway vehicles.
We help OEMs around the world speed up system development, reduce costs and bring
vehicles to market faster.
Danfoss – Your Strongest Partner in Mobile Hydraulics.
Go to www.powersolutions.danfoss.com for further product information.
Wherever off-highway vehicles are at work, so is Danfoss. We offer expert worldwide support
for our customers, ensuring the best possible solutions for outstanding performance. And
with an extensive network of Global Service Partners, we also provide comprehensive global
service for all of our components.
Please contact the Danfoss Power Solution representative nearest you.
Local address:
Danfoss
Power Solutions GmbH & Co. OHG
Krokamp 35
D-24539 Neumünster, Germany
Phone: +49 4321 871 0
Danfoss
Power Solutions ApS
Nordborgvej 81
DK-6430 Nordborg, Denmark
Phone: +45 7488 2222
Danfoss
Power Solutions (US) Company
2800 East 13th Street
Ames, IA 50010, USA
Phone: +1 515 239 6000
Danfoss
Power Solutions Trading
(Shanghai) Co., Ltd.
Building #22, No. 1000 Jin Hai Rd
Jin Qiao, Pudong New District
Shanghai, China 201206
Phone: +86 21 3418 5200
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to
products already on order provided that such alterations can be made without changes being necessary in specifications already agreed.
All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
L1327341 en-US • Rev 0101 • November 2015 www.danfoss.com
©
Danfoss A/S, 2015
Products we offer:
•
Bent Axis Motors
•
Closed Circuit Axial Piston
Pumps and Motors
•
Displays
•
Electrohydraulic Power
Steering
•
Electrohydraulics
•
Hydraulic Power Steering
•
Integrated Systems
•
Joysticks and Control
Handles
•
Microcontrollers and
Software
•
Open Circuit Axial Piston
Pumps
•
Orbital Motors
•
PLUS+1
®
GUIDE
•
Proportional Valves
•
Sensors
•
Steering
•
Transit Mixer Drives
Comatrol
www.comatrol.com
Schwarzmüller-Inverter
www.schwarzmueller-
inverter.com
Turolla
www.turollaocg.com
Hydro-Gear
www.hydro-gear.com
Daikin-Sauer-Danfoss
www.daikin-sauer-danfoss.com
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
The Danfoss TMTHW orbital motor offers robust bearing design, exceptional sealing, and high-pressure rating for demanding applications. Its strength and efficiency make it ideal for construction, agricultural, material handling, forestry, and marine equipment, among other heavy-duty machinery.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
iON F-20 Series User manual
-
Cisco Virtual Media Packager User guide
-
3M Round Conductor Flat Cable, 3625 Series Important information
-
AND AD-4713 User manual
-
-
PRONAR VMP-5ST Owner's manual
-
Dodge C-FLEX Module Warning Owner's manual
-
LightWave Systems Microwave Oven Silicon Power / Wavehead User manual
-
Reznor EGHB Installation guide
