ABB RER620 Technical Manual

Relion

®

Protection and Control

Advanced Recloser Protection and Control

RER620

Technical Manual

Document ID: 1MAC309294-MB

Issued: 7/20/2017

Revision:F

Product version: 1.3

Copyright

This document and parts thereof must not be reproduced or copied without written

permission from ABB, and the contents thereof must not be imparted to a third party, nor

used for any unauthorized purpose.

The software or hardware described in this document is furnished under a license and may

be used, copied, or disclosed only in accordance with the terms of such license.

Trademarks

ABB and Relion are registered trademarks of ABB Group. All other brand or product

names mentioned in this document may be trademarks or registered trademarks of their

respective holders.

Warranty

Please inquire about the terms of warranty from your nearest ABB representative.

ABB Inc.

Distribution Automation

4300 Coral Ridge Drive

Coral Springs, FL 33065, USA

Toll-free: 1 (800) 523-2620

Phone: +1 954-752-6700

Fax: +1 954 345-5329

http://www.abb.com/substationautomation

Disclaimer

The data, examples and diagrams in this manual are included solely for the concept or

product description and are not to be deemed as a statement of guaranteed properties. All

persons responsible for applying the equipment addressed in this manual must satisfy

themselves that each intended application is suitable and acceptable, including that any

applicable safety or other operational requirements are complied with. In particular, any

risks in applications where a system failure and/or product failure would create a risk for

harm to property or persons (including but not limited to personal injuries or death) shall

be the sole responsibility of the person or entity applying the equipment, and those so

responsible are hereby requested to ensure that all measures are taken to exclude or

mitigate such risks.

This document has been carefully checked by ABB but deviations cannot be completely

ruled out. In case any errors are detected, the reader is kindly requested to notify the

manufacturer. Other than under explicit contractual commitments, in no event shall ABB

be responsible or liable for any loss or damage resulting from the use of this manual or the

application of the equipment.

Conformity

This product complies with the directive of the Council of the European Communities on

the approximation of the laws of the Member States relating to electromagnetic

compatibility (EMC Directive 2004/108/EC) and concerning electrical equipment for use

within specified voltage limits (Low-voltage directive 2006/95/EC). This conformity is

the result of tests conducted by ABB in accordance with the product standards EN 50263

and EN 60255-26 for the EMC directive, and with the product standards EN 60255-6 and

EN 60255-27 for the low voltage directive. The relay is designed in accordance with the

international standards of the IEC 60255 series and ANSI C37.90.

1MAC309294-MB F Section

RER620 1

Technical Manual

Table of Contents

Section 1 Introduction......................................................................... 17

This manual............................................................................................ 17

Intended audience.................................................................................. 17

Product documentation .......................................................................... 18

Product documentation set ............................................................... 18

Document revision history................................................................. 19

Related documentation ..................................................................... 19

Symbols and conventions ...................................................................... 19

Safety indication symbols.................................................................. 19

Manual conventions .......................................................................... 20

Functions, codes and symbols.......................................................... 21

Section 2 RER620 overview............................................................... 25

Overview ................................................................................................ 25

Product series version history ........................................................... 25

PCM600 and relay connectivity package version ............................. 25

Local HMI ............................................................................................... 26

LCD ................................................................................................... 26

LEDs ................................................................................................. 27

Keypad .............................................................................................. 27

Web HMI ................................................................................................ 28

Authorization .......................................................................................... 29

Communication ...................................................................................... 30

Section 3 Basic functions ................................................................... 31

General parameters ............................................................................... 31

Self-supervision...................................................................................... 45

Internal faults..................................................................................... 45

Warnings ........................................................................................... 46

LED indication control ............................................................................ 50

Time synchronization ............................................................................. 50

Parameter setting groups ....................................................................... 51

Recorded data........................................................................................ 52

Non-volatile memory .............................................................................. 54

Binary input ............................................................................................ 54

Binary input filter time........................................................................ 54

Binary input inversion........................................................................ 55

Oscillation suppression ..................................................................... 56

GOOSE function blocks ......................................................................... 56

GOOSERCV_BIN function block....................................................... 57

Section 1MAC309294-MB F

2 RER620

Technical Manual

Function block .............................................................................. 57

Functionality ................................................................................. 57

Signals ......................................................................................... 57

GOOSERCV_DP function block........................................................ 57

Function block .............................................................................. 57

Functionality ................................................................................. 57

Signals ......................................................................................... 58

GOOSERCV_MV function block ....................................................... 58

Function block .............................................................................. 58

Functionality ................................................................................. 58

Signals ......................................................................................... 58

GOOSERCV_INT8 function block ..................................................... 59

Function block .............................................................................. 59

Functionality ................................................................................. 59

Signals ......................................................................................... 59

GOOSERCV_INTL function block ..................................................... 59

Function block .............................................................................. 59

Functionality ................................................................................. 59

Signals ......................................................................................... 60

GOOSERCV_CMV function block..................................................... 60

Function block .............................................................................. 60

Functionality ................................................................................. 60

Signals ......................................................................................... 60

GOOSERCV_ENUM function block .................................................. 61

Function block .............................................................................. 61

Functionality ................................................................................. 61

Signals ......................................................................................... 61

GOOSERCV_INT32 function block ................................................... 61

Function block .............................................................................. 61

Functionality ................................................................................. 62

Signals ......................................................................................... 62

Type conversion function blocks ............................................................ 62

QTY_GOOD function block ............................................................... 62

Function block .............................................................................. 62

Functionality ................................................................................. 62

Signals ......................................................................................... 63

QTY_BAD function block................................................................... 63

Function block .............................................................................. 63

Functionality ................................................................................. 63

Signals ......................................................................................... 63

T_HEALTH function block ................................................................. 64

Function block .............................................................................. 64

1MAC309294-MB F Section

RER620 3

Technical Manual

Functionality................................................................................. 64

Signals ......................................................................................... 64

T_F32_INT8 function block ............................................................... 64

Functionality................................................................................. 65

Settings ........................................................................................ 65

Configurable logic blocks ....................................................................... 65

Standard configurable logic blocks ................................................... 65

OR function block......................................................................... 65

Functionality................................................................................. 65

AND function block ...................................................................... 67

XOR function block ...................................................................... 68

NOT function block ...................................................................... 69

MAX3 function block .................................................................... 70

MIN3 function block ..................................................................... 70

R_TRIG function block ................................................................. 71

F_TRIG function block ................................................................. 72

T_POS_XX function blocks .......................................................... 73

SR function block ......................................................................... 75

PH_ORD_IN block ....................................................................... 76

PH_ORD_OUT block ................................................................... 77

Local/remote control function block CONTROL ................................ 78

Function block.............................................................................. 78

Functionality................................................................................. 79

Signals ......................................................................................... 80

Settings ........................................................................................ 80

Monitored data ............................................................................. 81

Factory settings restoration .................................................................... 81

Section 4 Protection functions............................................................ 83

Current protection................................................................................... 83

Single-phase non-directional overcurrent protection 51P/50P.......... 83

Identification................................................................................. 83

Function block.............................................................................. 83

Functionality................................................................................. 83

Operation principle....................................................................... 83

Measurement modes ................................................................... 87

Timer characteristics.................................................................... 87

Application ................................................................................... 89

Signals ......................................................................................... 94

Settings ........................................................................................ 95

Monitored data ............................................................................. 98

Technical data.............................................................................. 99

Technical revision history........................................................... 100

Section 1MAC309294-MB F

4 RER620

Technical Manual

Single-phase directional overcurrent protection 67/51P-1 and

67/51P-2.......................................................................................... 100

Identification ............................................................................... 100

Function block ............................................................................ 100

Functionality ............................................................................... 100

Operation principle ..................................................................... 101

Measuring modes....................................................................... 106

Directional overcurrent characteristics ....................................... 106

Application.................................................................................. 114

Signals ....................................................................................... 116

Settings ...................................................................................... 117

Monitored data ........................................................................... 122

Technical data............................................................................ 124

Non-directional neutral overcurrent protection 51N/50N ................. 124

Identification ............................................................................... 124

Function block ............................................................................ 125

Functionality ............................................................................... 125

Operation principle ..................................................................... 125

Measurement modes ................................................................. 127

Timer characteristics .................................................................. 127

Application.................................................................................. 130

Signals ....................................................................................... 131

Settings ...................................................................................... 133

Monitored data ........................................................................... 136

Technical data............................................................................ 137

Directional earth-fault protection 67/51N and 67/50N ..................... 137

Identification ............................................................................... 137

Function block ............................................................................ 138

Functionality ............................................................................... 138

Operation principle ..................................................................... 138

Directional ground-fault principles.............................................. 142

Measurement modes ................................................................. 148

Timer characteristics .................................................................. 149

Directional ground-fault characteristics ...................................... 151

Application.................................................................................. 161

Signals ....................................................................................... 163

Settings ...................................................................................... 164

Monitored data ........................................................................... 169

Technical data............................................................................ 170

Sensitive earth-fault protection 50SEF............................................ 170

Identification ............................................................................... 170

Function block ............................................................................ 171

1MAC309294-MB F Section

RER620 5

Technical Manual

Functionality............................................................................... 171

Principle of operation ................................................................. 171

Measurement modes ................................................................. 171

Timer characteristics.................................................................. 171

Application ................................................................................. 171

Signals ....................................................................................... 171

Settings ...................................................................................... 171

Monitored data ........................................................................... 171

Technical data............................................................................ 171

Negative phase-sequence current protection 46 ............................ 172

Identification............................................................................... 172

Function block............................................................................ 172

Functionality............................................................................... 172

Operation principle..................................................................... 172

Application ................................................................................. 174

Signals ....................................................................................... 176

Settings ...................................................................................... 176

Monitored data ........................................................................... 178

Technical data............................................................................ 178

Phase discontinuity protection 46PD .............................................. 179

Identification............................................................................... 179

Function block............................................................................ 179

Functionality............................................................................... 179

Operation principle..................................................................... 179

Application ................................................................................. 181

Signals ....................................................................................... 182

Settings ...................................................................................... 183

Monitored data ........................................................................... 183

Technical data............................................................................ 183

Three-phase transformer inrush detector INR ................................ 184

Identification............................................................................... 184

Function block............................................................................ 184

Functionality............................................................................... 184

Operation principle..................................................................... 184

Application ................................................................................. 186

Signals ....................................................................................... 187

Settings ...................................................................................... 187

Monitored data ........................................................................... 187

Technical data............................................................................ 188

Cold load timers ................................................................................... 188

Voltage protection ................................................................................ 188

Single-phase overvoltage protection 59.......................................... 188

Section 1MAC309294-MB F

6 RER620

Technical Manual

Identification ............................................................................... 188

Function block ............................................................................ 189

Functionality ............................................................................... 189

Operation principle ..................................................................... 189

Timer characteristics .................................................................. 194

Application.................................................................................. 194

Signals ....................................................................................... 195

Settings ...................................................................................... 195

Monitored data ........................................................................... 196

Technical data............................................................................ 197

Single-phase undervoltage protection 27........................................ 197

Identification ............................................................................... 197

Function block ............................................................................ 197

Functionality ............................................................................... 198

Operation principle ..................................................................... 198

Timer characteristics .................................................................. 203

Application.................................................................................. 203

Signals ....................................................................................... 204

Settings ...................................................................................... 204

Monitored data ........................................................................... 205

Technical data............................................................................ 206

Zero sequence overvoltage protection 59N .................................... 206

Identification ............................................................................... 206

Function block ............................................................................ 206

Functionality ............................................................................... 206

Operation principle ..................................................................... 207

Application.................................................................................. 208

Signals ....................................................................................... 208

Settings ...................................................................................... 209

Monitored data ........................................................................... 209

Technical data............................................................................ 209

Positive sequence overvoltage protection 59PS ............................. 210

Identification ............................................................................... 210

Function block ............................................................................ 210

Functionality ............................................................................... 210

Operation principle ..................................................................... 210

Application.................................................................................. 211

Signals ....................................................................................... 211

Settings ...................................................................................... 212

Technical data............................................................................ 212

Negative sequence overvoltage protection 47 ................................ 213

Identification ............................................................................... 213

1MAC309294-MB F Section

RER620 7

Technical Manual

Function block............................................................................ 213

Functionality............................................................................... 213

Operation principle..................................................................... 213

Application ................................................................................. 214

Signals ....................................................................................... 215

Settings ...................................................................................... 215

Monitored data ........................................................................... 215

Technical data............................................................................ 216

Frequency protection............................................................................ 216

Frequency protection 81O/81U, 81R .............................................. 216

Identification............................................................................... 216

Function block............................................................................ 217

Functionality............................................................................... 217

Operation principle..................................................................... 217

Application ................................................................................. 220

Signals ....................................................................................... 221

Settings ...................................................................................... 222

Monitored Data .......................................................................... 222

Technical data............................................................................ 223

Load shedding and restoration 81S ................................................ 223

Identification............................................................................... 223

Function block............................................................................ 223

Functionality............................................................................... 223

Operation principle..................................................................... 224

Application ................................................................................. 229

Signals ....................................................................................... 233

Settings ...................................................................................... 234

Monitored data ........................................................................... 234

Technical data............................................................................ 234

Other protection functions available in RER620................................... 235

Circuit breaker failure protection 50BFT ......................................... 235

Identification............................................................................... 235

Function block............................................................................ 235

Functionality............................................................................... 235

Operation principle..................................................................... 235

Application ................................................................................. 241

Signals ....................................................................................... 242

Settings ...................................................................................... 243

Monitored data ........................................................................... 243

Technical data............................................................................ 243

Single Phase Circuit breaker close failure protection 50BFC ......... 244

Identification............................................................................... 244

Section 1MAC309294-MB F

8 RER620

Technical Manual

Function block ............................................................................ 244

Functionality ............................................................................... 244

Operation principle ..................................................................... 244

Signals ....................................................................................... 247

Settings ...................................................................................... 248

Monitored data ........................................................................... 248

Technical data............................................................................ 248

High impedance fault detector HIZ.................................................. 248

Identification ............................................................................... 248

Function block symbol................................................................ 249

Functionality ............................................................................... 249

Principle of operation ................................................................. 249

Application.................................................................................. 251

Signals ....................................................................................... 252

Settings ...................................................................................... 252

Monitored data ........................................................................... 252

Fault locator FLOC .......................................................................... 253

Identification ............................................................................... 253

Function block ............................................................................ 253

Functionality ............................................................................... 253

Operation principle ..................................................................... 253

Application.................................................................................. 257

Signals ....................................................................................... 258

Settings ...................................................................................... 258

Monitored data ........................................................................... 258

Directional positive sequence power protection 32P....................... 259

Identification ............................................................................... 259

Function block ............................................................................ 259

Functionality ............................................................................... 259

Operation principle ..................................................................... 259

Application.................................................................................. 261

Signals ....................................................................................... 262

Settings ...................................................................................... 262

Monitored data ........................................................................... 263

Technical data............................................................................ 263

Directional negative/zero sequence power protection 32N ............. 263

Identification ............................................................................... 263

Function block ............................................................................ 264

Functionality ............................................................................... 264

Operation principle ..................................................................... 264

Application.................................................................................. 270

Signals ....................................................................................... 270

1MAC309294-MB F Section

RER620 9

Technical Manual

Settings ...................................................................................... 271

Monitored data ........................................................................... 271

Technical data............................................................................ 271

Section 5 Control functions .............................................................. 273

Circuit breaker control 52 ..................................................................... 273

Identification .................................................................................... 273

Function block ................................................................................. 273

Functionality .................................................................................... 273

Operation principle .......................................................................... 274

Application....................................................................................... 276

Signals ............................................................................................ 278

Settings ........................................................................................... 280

Monitored data ................................................................................ 280

Autoreclosing 79................................................................................... 280

Identification .................................................................................... 282

Function block ................................................................................. 283

Supporting function blocks......................................................... 283

Functionality .................................................................................... 283

Single phase tripping ................................................................. 284

Protection signal definition ......................................................... 285

Operation principle .......................................................................... 285

Active Phases Determination with SDAIGGIO Blocks ............... 287

Autorecloser function (Core) ...................................................... 289

Output Interface with SDAOGGIO Block ................................... 303

Zone sequence coordination........................................................... 304

Counters.......................................................................................... 305

Application....................................................................................... 305

Single Phase Tripping................................................................ 306

Configuration examples .................................................................. 310

Signals ............................................................................................ 314

Settings ........................................................................................... 317

Monitored data ................................................................................ 320

Technical data................................................................................. 323

Synch-check/voltage check 25............................................................. 323

Identification .................................................................................... 323

Function block ................................................................................. 323

Functionality .................................................................................... 323

Operation principle .......................................................................... 324

Application....................................................................................... 331

Signals ............................................................................................ 333

Settings ........................................................................................... 334

Monitored data ................................................................................ 335

Section 1MAC309294-MB F

10 RER620

Technical Manual

Technical data ................................................................................. 336

Loop control (DLCM) ............................................................................ 336

Identification .................................................................................... 336

Function block ................................................................................. 336

Functionality .................................................................................... 336

Sectionalizing Recloser.............................................................. 337

Midpoint Recloser ...................................................................... 338

Tiepoint Recloser ....................................................................... 338

Operation principle .......................................................................... 338

Application....................................................................................... 343

Three-Recloser Loop Control..................................................... 344

Five-Recloser Loop Control ....................................................... 346

Four-Recloser System Operation............................................... 350

Restoring Normal Operation ...................................................... 350

Signals............................................................................................. 351

Settings ........................................................................................... 352

Multipurpose Generic Up-Down Counter (UDFCNT) ........................... 353

Identification .................................................................................... 353

Function block ................................................................................. 353

Functionality .................................................................................... 353

Operation principle .......................................................................... 353

Signals............................................................................................. 355

Settings ........................................................................................... 355

Section 6 Condition monitoring functions ......................................... 357

Circuit breaker condition monitoring 52CM .......................................... 357

Identification .................................................................................... 357

Function block ................................................................................. 357

Functionality .................................................................................... 357

Operation principle .......................................................................... 358

Circuit breaker status ................................................................. 360

Circuit breaker operation monitoring .......................................... 360

Breaker contact travel time ........................................................ 361

Operation counter ...................................................................... 363

Accumulation of I

y

t ..................................................................... 364

Remaining life of the circuit breaker........................................... 365

Circuit breaker spring charged indication................................... 367

Gas pressure supervision .......................................................... 367

Application....................................................................................... 368

Signals............................................................................................. 372

Settings ........................................................................................... 374

Monitored data ................................................................................ 375

Technical data ................................................................................. 375

1MAC309294-MB F Section

RER620 11

Technical Manual

Fuse failure supervision 60 .................................................................. 376

Identification .................................................................................... 376

Function block ................................................................................. 376

Functionality .................................................................................... 376

Operation principle .......................................................................... 376

Application....................................................................................... 379

Signals ............................................................................................ 381

Settings ........................................................................................... 381

Monitored data ................................................................................ 382

Technical data................................................................................. 382

Section 7 Measurement functions .................................................... 383

Basic measurements............................................................................ 383

Functions......................................................................................... 383

Measurement functionality .............................................................. 383

Measurement function applications................................................. 391

Three-phase current IA, IB, IC ........................................................ 392

Identification............................................................................... 392

Function block............................................................................ 392

Signals ....................................................................................... 392

Settings ...................................................................................... 393

Monitored data ........................................................................... 394

Technical data............................................................................ 395

Three-phase voltage VA, VB, VC.................................................... 395

Identification............................................................................... 395

Function block............................................................................ 395

Signals ....................................................................................... 395

Settings ...................................................................................... 396

Monitored data ........................................................................... 397

Technical data............................................................................ 397

Ground current IG ........................................................................... 398

Identification............................................................................... 398

Function block............................................................................ 398

Signals ....................................................................................... 398

Settings ...................................................................................... 398

Monitored data ........................................................................... 399

Technical data............................................................................ 399

Ground voltage VG ......................................................................... 399

Identification............................................................................... 399

Function block............................................................................ 399

Signals ....................................................................................... 399

Settings ...................................................................................... 400

Monitored data ........................................................................... 400

Section 1MAC309294-MB F

12 RER620

Technical Manual

Technical data............................................................................ 400

Sequence current I1, I2, I0 .............................................................. 401

Identification ............................................................................... 401

Function block ............................................................................ 401

Signals ....................................................................................... 401

Settings ...................................................................................... 402

Monitored data ........................................................................... 403

Technical data............................................................................ 403

Phase sequence voltage V1, V2, V0............................................... 403

Identification ............................................................................... 403

Function block ............................................................................ 404

Signals ....................................................................................... 404

Settings ...................................................................................... 404

Monitored data ........................................................................... 405

Technical data............................................................................ 405

Single and Three-phase power, powerfactor and Three Phase

energy measurement P, SP, E........................................................ 406

Identification ............................................................................... 406

Function block ............................................................................ 406

Signals ....................................................................................... 406

Settings ...................................................................................... 407

Monitored data ........................................................................... 408

Technical data............................................................................ 410

Frequency ....................................................................................... 410

Identification ............................................................................... 410

Function block ............................................................................ 411

Signals ....................................................................................... 411

Settings ...................................................................................... 411

Monitored data ........................................................................... 411

Technical data............................................................................ 411

Section 8 Recording functions.......................................................... 413

Digital fault recorder DFR (RDRE) ....................................................... 413

Functionality .................................................................................... 413

Recorded analog inputs ............................................................. 413

Triggering alternatives................................................................ 413

Length of recordings........................................................................ 415

Sampling frequencies................................................................. 415

Uploading of recordings ............................................................. 415

Deletion of recordings ................................................................ 416

Storage mode............................................................................. 416

Pre-trigger and post-trigger data ................................................ 417

Operation modes........................................................................ 417

1MAC309294-MB F Section

RER620 13

Technical Manual

Exclusion mode.......................................................................... 418

Configuration................................................................................... 418

Application....................................................................................... 419

Settings ........................................................................................... 420

Monitored data ................................................................................ 421

Section 9 Other functions ................................................................. 423

Uninterruptible Power Supply UPS ...................................................... 423

Function block ................................................................................. 423

Functionality .................................................................................... 423

Input power requirements .......................................................... 425

Input Power Measurement .............................................................. 426

Loss of UPS input power alarm. ................................................ 426

Battery management.................................................................. 427

Auxiliary Power Supply .............................................................. 428

Actuator Drive Power Source (Boost Supply) ............................ 428

Heater control switch ................................................................. 428

RER620 power........................................................................... 429

RS485 communications ............................................................. 429

Connections .................................................................................... 430

Signals ............................................................................................ 431

CVD Voltage Clamping ................................................................... 431

Settings ........................................................................................... 434

Monitored data ................................................................................ 435

Universal power drive UPD .................................................................. 436

Function block ................................................................................. 436

Functionality .................................................................................... 436

Connections .................................................................................... 439

Signals ............................................................................................ 440

Settings ........................................................................................... 440

Monitored data ................................................................................ 440

Programmable buttons FKEYGGIO ..................................................... 441

Function block ................................................................................. 441

Functionality .................................................................................... 441

Signals ............................................................................................ 442

Move function block MVGAPC ............................................................. 443

Function block ................................................................................. 443

Functionality .................................................................................... 443

Signals ............................................................................................ 443

Pulse timer function block PTGAPC..................................................... 444

Function block ................................................................................. 444

Functionality .................................................................................... 444

Signals ............................................................................................ 445

Section 1MAC309294-MB F

14 RER620

Technical Manual

Settings ........................................................................................... 446

Technical data ................................................................................. 446

Generic control points SPCGGIO......................................................... 447

Function block ................................................................................. 447

Functionality .................................................................................... 447

Signals............................................................................................. 448

Settings ........................................................................................... 449

Set-reset flip flops SRGAPC................................................................. 449

Function block ................................................................................. 449

Functionality .................................................................................... 449

Signals............................................................................................. 450

Settings ........................................................................................... 451

Time-delay-off timers TOFGAPC ......................................................... 452

Function block ................................................................................. 452

Functionality .................................................................................... 452

Signals............................................................................................. 453

Settings ........................................................................................... 454

Technical data ................................................................................. 454

Time-delay-on timers TONGAPC ......................................................... 455

Function block ................................................................................. 455

Functionality .................................................................................... 455

Signals............................................................................................. 456

Settings ........................................................................................... 457

Technical data ................................................................................. 457

Section 10 General function block features ........................................ 459

Definite time characteristics.................................................................. 459

Definite time operation .................................................................... 459

Current based inverse definite minimum time characteristics .............. 463

IDMT curves for overcurrent protection........................................... 463

Standard inverse-time characteristics ........................................ 465

Recloser inverse-time characteristics ........................................ 480

User-programmable inverse-time characteristics....................... 521

RI and RD-type inverse-time characteristics.............................. 521

Reset in inverse-time modes........................................................... 524

Inverse-timer freezing...................................................................... 533

Voltage based inverse definite minimum time characteristics .............. 534

IDMT curves for overvoltage protection .......................................... 534

Standard inverse-time characteristics for overvoltage

protection ................................................................................... 537

User programmable inverse-time characteristics for

overvoltage protection................................................................ 540

IDMT curve saturation of overvoltage protection ....................... 541

Page is loading ...

ABB RER620 Technical Manual

This manual is also suitable for

ABB RER620 Technical Manual

Related papers

Other documents