Duerkopp Adler 911-210 User manual

Type
User manual

This manual is also suitable for

911
Additional Instructions
Slideway lining for the tabletop
All rights reserved.
Property of Dürkopp Adler GmbH and protected by copyright. Any reuse of these contents, in-
cluding extracts, is prohibited without the prior written approval of
Dürkopp Adler GmbH.
Copyright © Dürkopp Adler GmbH 2020
IMPORTANT
READ CAREFULLY BEFORE USE
KEEP FOR FUTURE REFERENCE
Table of Contents
Additional Instructions 911 - 01.0 - 12/2020 1
1 About these additional instructions .........................................3
2 Components of the kit................................................................4
3 Attaching the slideway lining to the tabletop ..........................5
4 Appendix .....................................................................................6
Table of Contents
2 Additional Instructions 911 - 01.0 - 12/2020
About these additional instructions
Additional Instructions 911 - 01.0 - 12/2020 3
1 About these additional instructions
These additional instructions describe how to attach the slideway lining for
the tabletop to machines grouped in the 911 class.
Important
The slideway lining for the tabletop is 1.5 mm thick.
Before attaching the slideway lining, you need to shift the height of the
machine head by 1.5 mm and realign the machine head ( Service
I
nstructions).
Components of the kit
4 Additional Instructions 911 - 01.0 - 12/2020
2 Components of the kit
Check whether the scope of delivery for the kit is correct prior to attaching
the slideway lining.
Different kits are available that vary with t
he size of the sewing field.
The installation procedure is the same for all kits.
Kit 0911 597834 0911 597844 0911 597845 0911 597864
Sewing field size 3020 6055 2010 6020
Plate 0911 400724 0911 400754 0911 400694 0911 400774
Double sided adhesive
tape
B760 200015
Additional Instructions 0791 911714 EN
Attaching the slideway lining to the tabletop
Additional Instructions 911 - 01.0 - 12/2020 5
3 Attaching the slideway lining to the tabletop
Fig. 1: Attaching the slideway lining to the tabletop
To attach the slideway lining:
1. Remove the sliding plate (not shown).
2. Affix the double-sided adhesive tape on the underside of the slideway
lin
ing (2) and peel off the protective film from the tape (see
Appendix ( p. 6)).
3. Align the slideway lining (2) flush with the tabletop (1) and apply it.
4. Bond the inner insertion plate of the slideway lining (4) into the tabletop
cut-
out (3).
5. Reinsert the sliding plate.
6. Align the height of the machine head ( Service Instructions).
(1) - Tabletop
(2) - Slideway lining
(3) - Tabletop cut-out
(4) - Inner insert of the slideway lining
③④
Appendix
6 Additional Instructions 911 - 01.0 - 12/2020
4Appendix
Positions for double sided adhesive tape at the bottom side of the
slideway lining
Abb. 2: Sewing field size 2010
Abb. 3: Sewing field size 3020
Double sided adhesive
tape flush fitting on
POM-plate
Double sided adhesive
tape flush fitting on
POM-plate
Appendix
Additional Instructions 911 - 01.0 - 12/2020 7
Abb. 4: Sewing field size 6020
Abb. 5: Sewing field size 6055
Double sided adhesive
tape flush fitting on
POM-plate
Double sided adhesive
tape flush fitting on
POM-plate
Appendix
8 Additional Instructions 911 - 01.0 - 12/2020
DÜRKOPP ADLER GmbH
Potsdamer Str. 190
33719 Bielefeld
Germany
Phone: +49 (0) 521 925 00
www.duerkopp-adler.com
Subject to design changes - Part of the machines shown with additional equipment - Printed in Germany
© Dürkopp Adler GmbH - Original Instructions - 0791 911714 EN - 01.0 - 12/2020
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Duerkopp Adler 911-210 User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI