ASROCK ALIVEXFIRE-ESATA2 R3.0_987

11

1

ASRock ALiveXFire-eSATA2 Motherboard

EnglishEnglish

English

Copyright Notice:Copyright Notice:

Copyright Notice:

No part of this installation guide may be reproduced, transcribed, transmitted, or trans-

lated in any language, in any form or by any means, except duplication of documen-

tation by the purchaser for backup purpose, without written consent of ASRock Inc.

Products and corporate names appearing in this guide may or may not be registered

trademarks or copyrights of their respective companies, and are used only for identifica-

tion or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:Disclaimer:

Disclaimer:

Specifications and information contained in this guide are furnished for informational

use only and subject to change without notice, and should not be constructed as a

commitment by ASRock. ASRock assumes no responsibility for any errors or omissions

that may appear in this guide.

With respect to the contents of this guide, ASRock does not provide warranty of any kind,

either expressed or implied, including but not limited to the implied warranties or

conditions of merchantability or fitness for a particular purpose. In no event shall

ASRock, its directors, officers, employees, or agents be liable for any indirect, special,

incidental, or consequential damages (including damages for loss of profits, loss of

business, loss of data, interruption of business and the like), even if ASRock has been

advised of the possibility of such damages arising from any defect or error in the guide

or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

Published December 2007

CALIFORNIA, USA ONLY

The Lithium battery adopted on this motherboard contains Perchlorate, a toxic

substance controlled in Perchlorate Best Management Practices (BMP) regulations

passed by the California Legislature. When you discard the Lithium battery in

California, USA, please follow the related regulations in advance.

“Perchlorate Material-special handling may apply, see

www.dtsc.ca.gov/hazardouswaste/perchlorate”

ASRock Website: http://www.asrock.com

22

2

ASRock ALiveXFire-eSATA2 Motherboard

EnglishEnglish

English

Motherboard LMotherboard L

Motherboard L

ayoutayout

ayout

1 PS2_USB_PW1 Jumper 19 USB 2.0 Header (USB6_7, Blue)

2 ATX 12V Connector (ATX12V1) 20 USB 2.0 Header (USB8_9, Blue)

3 CPU Fan Connector (CPU_FAN1) 21 Serial ATAII Connector

4 ATX Power Connector (ATXPWR1) (SATAII_BLUE (PORT 4))

5 AM2 940-Pin CPU Socket 22 Chassis Fan Connector (CHA_FAN1)

6 CPU Heatsink Retention Module 23 System Panel Header (PANEL1)

7 2 x 240-pin DDR2 DIMM Slots 24 Chassis Speaker Header (SPEAKER 1)

(Dual Channel A: DDRII_1, DDRII_2; Yellow) 25 Floppy Connector (FLOPPY1)

8 2 x 240-pin DDR2 DIMM Slots 26 Front Panel Audio Header (HD_AUDIO1)

(Dual Channel B: DDRII_3, DDRII_4; Orange) 27 PCI Slots (PCI1- 3)

9 IDE1 Connector (IDE1, Blue) 28 HDMI_SPDIF Header (HDMI_SPDIF1)

10 North Bridge Controller 29 BIOS LPC Chip

11 Clear CMOS Jumper (CLRCMOS1) 30 Infrared Module Connector (IR1)

12 PCI Express x16 Slot (PCIE3) 31 PCIE Express Slot (PCIE2/PCIE SWITCH)

13 South Bridge Controller 32 PCI Express x1 Slot (PCIE1)

14 Serial ATAII Connector (SATAII_ORANGE (PORT 2))33 SLI / XFIRE Power Connector

15 Serial ATAII Connector (SATAII_RED (PORT 1)) 34 Internal Audio Connector: CD1 (Black)

16 Serial ATAII Connector (SATAII_BLACK (PORT 3)) 35 eSATAII Connector (eSATAII_TOP)

17 USB 2.0 Header (USB2_3, Blue) 36 eSATAII Connector (eSATAII_BOTTOM)

18 USB 2.0 Header (USB4_5, Blue)

33

3

ASRock ALiveXFire-eSATA2 Motherboard

EnglishEnglish

English

ASRASR

ASR

ock 6CH_eSAock 6CH_eSA

ock 6CH_eSA

TT

T

AII I/OAII I/O

AII I/O

1 Parallel Port 7 Microphone (Pink)

2 RJ-45 Port 8 USB 2.0 Ports (USB01)

3 Rear Speaker (Black) 9 eSATAII Ports

4 Central / Bass (Orange) 10 COM Port

5 Line In (Light Blue) 11 PS/2 Keyboard Port (Purple)

* 6 Front Speaker (Lime) 12 PS/2 Mouse Port (Green)

* If you use 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”.

See the table below for connection details in accordance with the type of speaker you use.

TABLE for Audio Output Connection

* To enable Multi-Streaming function, you need to connect a front panel audio cable to the front

panel audio header. Please refer to below steps for the software setting of Multi-Streaming.

For Windows

®

XP:

After restarting your computer, you will find “Mixer” tool on your system. Please select “Mixer

ToolBox” , click “Enable playback multi-streaming”, and click “ok”. Choose “2CH” or

“4CH” and then you are allowed to select “Realtek HDA Primary output” to use Rear Speaker

and Front Speaker, or select “Realtek HDA Audio 2nd output” to use front panel audio. Then

reboot your system.

For Windows

®

Vista

TM

:

After restarting your computer, please double-click “Realtek HD Audio Manager” on the

system tray. Set “Speaker Configuration” to “5.1 Speaker”. Click “Device advanced settings”,

choose “Make front and rear output devices playbacks two different audio streams

simultaneously”, and click “ok”. Then reboot your system.

Audio Output Channels Front Speaker Rear Speaker Central / Bass

(No. 6) (No. 3) (No. 4)

2 V -- --

4VV--

6VVV

44

4

ASRock ALiveXFire-eSATA2 Motherboard

1.1.

1.

IntroductionIntroduction

Introduction

Thank you for purchasing ASRock ALiveXFire-eSATA2 motherboard, a reliable

motherboard produced under ASRock’s consistently stringent quality control. It de-

livers excellent performance with robust design conforming to ASRock’s commit-

ment to quality and endurance.

This Quick Installation Guide contains introduction of the motherboard and step-by-

step installation guide. More detailed information of the motherboard can be found in

the user manual presented in the Support CD.

Because the motherboard specifications and the BIOS software might

be updated, the content of this manual will be subject to change without

notice. In case any modifications of this manual occur, the updated

version will be available on ASRock website without further notice. You

may find the latest VGA cards and CPU support lists on ASRock

website as well.

ASRock website http://www.asrock.com

If you require technical support related to this motherboard, please

visit our website for specific information about the model you are

using.

www.asrock.com/support/index.asp

1.11.1

1.1

PP

P

ackack

ack

age Contentsage Contents

age Contents

1 x ASRock ALiveXFire-eSATA2 Motherboard

(ATX Form Factor: 12.0-in x 8.2-in, 30.5 cm x 20.8 cm)

1 x ASRock ALiveXFire-eSATA2 Quick Installation Guide

1 x ASRock ALiveXFire-eSATA2 Support CD

1 x Ultra ATA 66/100/133 IDE Ribbon Cable (80-conductor)

1 x 3.5-in Floppy Drive Ribbon Cable

2 x Serial ATA (SATA) Data Cables (Optional)

1 x Serial ATA (SATA) HDD Power Cable (Optional)

1 x HDMI_SPDIF Cable (Optional)

1 x ASRock 6CH_eSATAII I/O Shield

1 x USB Bracket

1 x PCIE Switch Card

This motherboard is bundled with one PCIE Switch card installed on PCIE2/

PCIE SWITCH slot, which allows you better flexibility to choose PCIE

functions between one PCIE x16 slot and two PCIE slots for ATI

TM

CrossFire

TM

without setting up jumpers.

EnglishEnglish

English

55

5

ASRock ALiveXFire-eSATA2 Motherboard

EnglishEnglish

English

1.21.2

1.2

SpecificationsSpecifications

Specifications

Platform - ATX Form Factor: 12.0-in x 8.2-in, 30.5 cm x 20.8 cm

CPU - Socket AM2 for AMD Phenom

TM

X4 / X2, Athlon 64FX / 64X2 /

X2 / 64 and Sempron processors

- AMD LIVE!

TM

Ready

- Supports AMD’s Cool ‘n’ Quiet

TM

Technology

- FSB 1000 MHz (2.0 GT/s)

- Supports Untied Overclocking Technology (see CAUTION 1)

- Supports Hyper-Transport Technology

Chipset - Northbridge: AMD 480X CrossFire

TM

- Southbridge:ATI

TM

SB600

Memory - Dual Channel DDR2 Memory Technology (see CAUTION 2)

- 4 x DDR2 DIMM slots

- Support DDR2 1066/800/667/533 (see CAUTION 3)

- Max. capacity: 8GB (see CAUTION 4)

Hybrid Booster - CPU Frequency Stepless Control (see CAUTION 5)

- ASRock U-COP (see CAUTION 6)

- Boot Failure Guard (B.F.G.)

- AM2 Boost: ASRock Patented Technology to boost memory

performance up to 12.5% (see CAUTION 7)

Expansion Slot - Supports ATI

TM

CrossFire

TM

graphics cards

(see CAUTION 8)

- 1 x PCI Express x16 slot with PCIE Switch card or 2 x PCI

Express Graphics slots for ATI

TM

CrossFire

TM

(see CAUTION 9)

- 1 x PCI Express x1 slot

- 3 x PCI slots

Audio - 5.1 CH Windows

®

Vista

TM

Premium Level HD Audio

(ALC662 Audio Codec)

LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111B

- Supports Wake-On-LAN

Rear Panel I/O ASRock 6CH_eSATAII I/O

- 1 x PS/2 Mouse Port

- 1 x PS/2 Keyboard Port

- 1 x Serial Port: COM1

- 1 x Parallel Port (ECP/EPP Support)

- 2 x Ready-to-Use USB 2.0 Ports

- 2 x eSATAII Ports

- 1 x RJ-45 Port

66

6

ASRock ALiveXFire-eSATA2 Motherboard

EnglishEnglish

English

- HD Audio Jack: Rear Speaker / Central/Bass / Line in / Front

Speaker / Microphone (see CAUTION 10)

Connector - 4 x SATAII 3.0Gb/s connectors, support RAID (RAID 0,

RAID 1 and RAID 10), NCQ, AHCI and “Hot Plug” functions

(see CAUTION 11)

- 2 x eSATAII 3.0Gb/s connectors (shared with 2 SATAII ports),

support RAID (RAID 0 and RAID 1), NCQ, AHCI and “Hot Plug”

functions (see CAUTION 12)

- 1 x ATA133 IDE connector (supports 2 x IDE devices)

- 1 x Floppy connector

- 1 x IR header

- 1 x HDMI_SPDIF header

- CPU/Chassis FAN connector

- 20 pin ATX power connector

- 4 pin 12V power connector

- SLI/XFire power connector

- CD in header

- Front panel audio connector

- 4 x USB 2.0 headers (support 8 USB 2.0 ports)

(see CAUTION 13)

BIOS Feature - 4Mb AMI BIOS

- AMI Legal BIOS

- Supports “Plug and Play”

- ACPI 1.1 Compliance Wake Up Events

- Supports jumperfree

- SMBIOS 2.3.1 Support

Support CD - Drivers, Utilities, AntiVirus Software (Trial Version)

Hardware - CPU Temperature Sensing

Monitor - Chassis Temperature Sensing

- CPU Fan Tachometer

- Chassis Fan Tachometer

- CPU Quiet Fan

- Voltage Monitoring: +12V, +5V, +3.3V, Vcore

OS - Microsoft

®

Windows

®

2000 / XP / XP Media Center / XP 64-bit

/ Vista

TM

/ Vista

TM

64-bit compliant

Certifications - FCC, CE, Microsoft

®

WHQL Certificated

77

7

ASRock ALiveXFire-eSATA2 Motherboard

EnglishEnglish

English

WARNING

Please realize that there is a certain risk involved with overclocking, including adjusting

the setting in the BIOS, applying Untied Overclocking Technology, or using the third-

party overclocking tools. Overclocking may affect your system stability, or even

cause damage to the components and devices of your system. It should be done at

your own risk and expense. We are not responsible for possible damage caused by

overclocking.

CAUTION!

1. This motherboard supports Untied Overclocking Technology. Please read

“Untied Overclocking Technology” on page 37 for details.

2. This motherboard supports Dual Channel Memory Technology. Before

you implement Dual Channel Memory Technology, make sure to read

the installation guide of memory modules on page 11 for proper

installation.

3. Whether 1066MHz memory speed is supported depends on the AM2+

CPU you adopt. If you want to adopt DDR2 1066 memory module on this

motherboard, please refer to the memory support list on our website for

the compatible memory modules.

ASRock website http://www.asrock.com

4. Due to the operating system and chipset limitation, the actual memory

size may be less than 4GB for the reservation for system usage under

Windows

®

XP, Windows

®

Vista

TM

, and Windows

®

Vista

TM

64-bit. For

Windows

®

XP 64-bit with 64-bit CPU, there is no such limitation.

5. Although this motherboard offers stepless control, it is not recommended to

perform over-clocking. Frequencies other than the recommended CPU bus

frequencies may cause the instability of the system or damage the CPU.

6. While CPU overheat is detected, the system will automatically shutdown.

Before you resume the system, please check if the CPU fan on the

motherboard functions properly and unplug the power cord, then plug it

back again. To improve heat dissipation, remember to spray thermal grease

between the CPU and the heatsink when you install the PC system.

7. This motherboard supports ASRock AM2 Boost overclocking technology. If

you enable this function in the BIOS setup, the memory performance will

improve up to 12.5%, but the effect still depends on the AM2 CPU you

adopt. Enabling this function will overclock the chipset/CPU reference clock.

However, we can not guarantee the system stability for all CPU/DRAM

configurations. If your system is unstable after AM2 Boost function is enabled,

it may not be applicative to your system. You may choose to disable this

function for keeping the stability of your system.

8. Please remove PCIE Switch card from PCIE2/PCIE SWITCH slot before

you use ATI

TM

CrossFire

TM

function. In CrossFire

TM

mode, the two ATI

TM

graph-

ics cards you install should be from the same GPU family.

88

8

ASRock ALiveXFire-eSATA2 Motherboard

EnglishEnglish

English

9. This motherboard is bundled with one PCIE Switch card installed on PCIE2/

PCIE SWITCH slot, which allows you better flexibility to choose PCIE func-

tions between one PCIE x16 slot and two PCIE slots for ATI

TM

CrossFire

TM

without setting up jumpers. To avail of the PCI Express x16 graphics card

installed on PCIE3 slot work at PCIE x16 bandwidth, please make sure that

PCIE Switch card is installed on PCIE2/PCIE SWITCH slot. Please refer to

page 15 for details of installing a single graphics card.

10. For microphone input, this motherboard supports both stereo and mono

modes. For audio output, this motherboard supports 2-channel, 4-channel

and 6-channel modes. Please check the table on page 3 for proper

connection.

11. Before installing SATAII hard disk to SATAII connector, please read the “SATAII

Hard Disk Setup Guide” on page 30 to adjust your SATAII hard disk drive to

SATAII mode. You can also connect SATA hard disk to SATAII connector

directly.

12. This motherboard supports eSATAII interface, the external SATAII

specification. Please read “eSATAII Interface Introduction” on page 27

for details about eSATAII and eSATAII installation procedures.

13. Power Management for USB 2.0 works fine under Microsoft

®

Windows

®

Vista

TM

64-bit / Vista

TM

/ XP 64-bit / XP SP1 or SP2 / 2000 SP4.

1.31.3

1.3

Minimum Hardware RMinimum Hardware R

Minimum Hardware R

equirement Tequirement T

equirement T

able for Wable for W

able for W

indowsindows

indows

®®

®

VistaVista

Vista

TMTM

TM

Premium 2007 and Basic Logo Premium 2007 and Basic Logo

Premium 2007 and Basic Logo

For system integrators and users who purchase this motherboard and

plan to submit Windows

®

Vista

TM

Premium 2007 and Basic logo, please

follow below table for minimum hardware requirements.

CPU Sempron 2800+

Memory 1GB system memory (Premium)

512MB Single Channel (Basic)

VGA DX9.0 with WDDM Driver

with 128bit VGA memory (Premium)

with 64bit VGA memory (Basic)

* After June 1, 2007, all Windows

®

Vista

TM

systems are required to meet above

minimum hardware requirements in order to qualify for Windows

®

Vista

TM

Premium

2007 logo.

99

9

ASRock ALiveXFire-eSATA2 Motherboard

EnglishEnglish

English

2.2.

2.

InstallationInstallation

Installation

This is an ATX form factor (12.0-in x 8.2-in, 30.5 cm x 20.8 cm) motherboard.

Before you install the motherboard, study the configuration of your chassis to en-

sure that the motherboard fits into it.

Pre-installation PrecautionsPre-installation Precautions

Pre-installation Precautions

Take note of the following precautions before you install motherboard

components or change any motherboard settings.

Before you install or remove any component, ensure that the

power is switched off or the power cord is detached from the

power supply. Failure to do so may cause severe damage to the

motherboard, peripherals, and/or components.

1. Unplug the power cord from the wall socket before touching any

component.

2. To avoid damaging the motherboard components due to static

electricity, NEVER place your motherboard directly on the carpet or

the like. Also remember to use a grounded wrist strap or touch a

safety grounded object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded anti-

static pad or in the bag that comes with the component.

5. When placing screws into the screw holes to secure the motherboard

to the chassis, please do not over-tighten the screws! Doing so may

damage the motherboard.

1010

10

ASRock ALiveXFire-eSATA2 Motherboard

2.12.1

2.1

CPU InstallationCPU Installation

CPU Installation

Step 1. Unlock the socket by lifting the lever up to a 90

o

angle.

Step 2. Position the CPU directly above the socket such that the CPU corner with

the golden triangle matches the socket corner with a small triangle.

Step 3. Carefully insert the CPU into the socket until it fits in place.

The CPU fits only in one correct orientation. DO NOT force the CPU

into the socket to avoid bending of the pins.

Step 4. When the CPU is in place, press it firmly on the socket while you push

down the socket lever to secure the CPU. The lever clicks on the side tab

to indicate that it is locked.

2.22.2

2.2

Installation of CPU Fan and HeatsinkInstallation of CPU Fan and Heatsink

Installation of CPU Fan and Heatsink

After you install the CPU into this motherboard, it is necessary to install a

larger heatsink and cooling fan to dissipate heat. You also need to spray

thermal grease between the CPU and the heatsink to improve heat

dissipation. Make sure that the CPU and the heatsink are securely fas-

tened and in good contact with each other. Then connect the CPU fan to

the CPU FAN connector (CPU_FAN1, see Page 2, No. 3). For proper

installation, please kindly refer to the instruction manuals of the CPU fan

and the heatsink.

STEP 1:

Lift Up The Socket Lever

STEP 2 / STEP 3:

Match The CPU Golden Triangle

To The Socket Corner Small

Triangle

STEP 4:

Push Down And Lock

The Socket Lever

Lever 90° Up

CPU Golden Triangle

Socket Corner Small Triangle

EnglishEnglish

English

1111

11

ASRock ALiveXFire-eSATA2 Motherboard

EnglishEnglish

English

2.3 Installation of Memor2.3 Installation of Memor

2.3 Installation of Memor

y Modules (DIMM)y Modules (DIMM)

y Modules (DIMM)

This motherboard provides four 240-pin DDR2 (Double Data Rate 2) DIMM slots,

and supports Dual Channel Memory Technology. For dual channel configuration,

you always need to install identical (the same brand, speed, size and chip-type)

DDR2 DIMM pair in the slots of the same color. In other words, you have to install

identical DDR2 DIMM pair in Dual Channel A (DDRII_1 and DDRII_2; Yellow slots;

see p.2 No.7) or identical DDR2 DIMM pair in Dual Channel B (DDRII_3 and

DDRII_4; Orange slots; see p.2 No.8), so that Dual Channel Memory Technology

can be activated. This motherboard also allows you to install four DDR2 DIMMs for

dual channel configuration, and please install identical DDR2 DIMMs in all four

slots. You may refer to the Dual Channel Memory Configuration Table below.

Dual Channel Memory Configurations

DDRII_1 DDRII_2 DDRII_3 DDRII_4

(Yellow Slot) (Yellow Slot) (Orange Slot) (Orange Slot)

(1) Populated Populated - -

(2) - - Populated Populated

(3)* Populated Populated Populated Populated

* For the configuration (3), please install identical DDR2 DIMMs in all four slots.

1. If you want to install two memory modules, for optimal compatibil-

ity and reliability, it is recommended to install them in the slots of

the same color. In other words, install them either in the set of

yellow slots (DDRII_1 and DDRII_2), or in the set of orange slots

(DDRII_3 and DDRII_4).

2. If only one memory module or three memory modules are in-

stalled in the DDR2 DIMM slots on this motherboard, it is unable to

activate the Dual Channel Memory Technology.

3. If a pair of memory modules is NOT installed in the same Dual

Channel, for example, installing a pair of memory modules in

DDRII_1 and DDRII_3, it is unable to activate the Dual Channel

Memory Technology .

4. It is not allowed to install a DDR memory module into DDR2 slot;

otherwise, this motherboard and DIMM may be damaged.

1212

12

ASRock ALiveXFire-eSATA2 Motherboard

EnglishEnglish

English

Installing a DIMMInstalling a DIMM

Installing a DIMM

Please make sure to disconnect power supply before adding or

removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.

Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break

on the slot.

The DIMM only fits in one correct orientation. It will cause permanent

damage to the motherboard and the DIMM if you force the DIMM into the

slot at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully

snap back in place and the DIMM is properly seated.

1313

13

ASRock ALiveXFire-eSATA2 Motherboard

EnglishEnglish

English

2.4 Expansion Slots (PCI and PCI Express Slots)2.4 Expansion Slots (PCI and PCI Express Slots)

2.4 Expansion Slots (PCI and PCI Express Slots)

There are 3 PCI slots and 3 PCI Express slots on this motherboard.

PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI

interface.

PCIE Slots: PCIE1 slot (PCI Express x1 slot) is used for PCI Express cards with

x1 lane width, such as Gigabit LAN card, SATA2 card, etc.

For PCIE2/PCIE SWITCH slot and PCIE3 slot, you may choose to use

one PCI Express x16 slot with PCIE Switch card or two PCI Express

Graphics slots for ATI

TM

CrossFire

TM

.

NOTE:

If you want the PCI Express x16 graphics card on PCIE3 slot to work at PCIE

x16 bandwidth, you need to install PCIE Switch card on PCIE2/PCIE SWITCH

slot. Please refer to page 15 for details of installing a single graphics card.

If you want to enable ATI

TM

CrossFire

TM

feature, please refer to page 16 for

details of installing CrossFire

TM

graphics cards.

Please refer to the table below for possible PCIE2/PCIE SWITCH slot

and PCIE3 slot configurations.

PCIE2/PCIE Switch Slot and PCIE3 Slot Configurations

PCIE2/PCIE SWITCH Slot PCIE3 Slot

Card Type Card Type

Single Graphics Card * PCIE Switch Card PCIE x16 graphics card

Dual Graphics Cards

in CrossFire

TM

Mode **

ATI

TM

Standard Radeon

(CrossFire

TM

Ready)

graphics card

ATI

TM

Radeon CrossFire

TM

Edition graphics card

* To avail of the PCI Express x16 graphics card installed on PCIE3 slot work at

PCIE x16 bandwidth, please make sure that PCIE Switch card is installed on

PCIE2/PCIE SWITCH slot. Please refer to page 15 for details of installing a

single graphics card.

** Please remove PCIE Switch card from PCIE2/PCIE SWITCH slot before you

use ATI

TM

CrossFire

TM

function. In CrossFire

TM

mode, the two ATI

TM

graphics

cards you install should be from the same GPU family.

1414

14

ASRock ALiveXFire-eSATA2 Motherboard

EnglishEnglish

English

Installing an expansion cardInstalling an expansion card

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power

supply is switched off or the power cord is unplugged. Please read the

documentation of the expansion card and make necessary hardware

settings for the card before you start the installation.

Step 2. Remove the system unit cover (if your motherboard is already installed in

a chassis).

Step 3. Remove the bracket facing the slot that you intend to use. Keep the

screws for later use.

Step 4. Align the card connector with the slot and press firmly until the card is

completely seated on the slot.

Step 5. Fasten the card to the chassis with screws.

Step 6. Replace the system cover.

1515

15

ASRock ALiveXFire-eSATA2 Motherboard

EnglishEnglish

English

2.5 Installing a Single Graphics Card2.5 Installing a Single Graphics Card

2.5 Installing a Single Graphics Card

Step 1. Install a PCI Express x16 graphics card on PCIE3 slot. Please refer to

page 14 for proper procedures of installing an expansion card.

Step 2. Make sure that the PCIE Switch card is installed on PCIE2/PCIE SWITCH

slot to avail of the PCI Express x16 graphics card full x16 bandwidth.

Step 3. Connect one end of the monitor cable to the PCI Express x16 graphics

card on PCIE3 slot.

Step 4. Connect another end of the monitor cable to the corresponding port on

your monitor.

Step 5. Connect an auxiliary power source from the power supply to the PCI

Express x16 graphics card on PCIE3 slot. (Only when your graphics

card provides such a power connector.)

PCIE Switch card

on PCIE2/PCIE

SWITCH slot

1616

16

ASRock ALiveXFire-eSATA2 Motherboard

EnglishEnglish

English

2.6 Installing CrossFire2.6 Installing CrossFire

2.6 Installing CrossFire

TMTM

TM

Graphics Cards Graphics Cards

Graphics Cards

This motherboard supports CrossFire

TM

feature. CrossFire

TM

technology offers the

most advantageous means available of combining multiple high performance Graphics

Processing Units (GPU) in a single PC. Combining a range of different operating

modes with intelligent software design and an innovative interconnect mechanism,

CrossFire

TM

enables the highest possible level of performance and image quality in

any 3D application. Currently CrossFire

TM

feature is only supported with Windows

®

XP with Service Pack 2; it may be supported with other OS in the future, such as

Windows

®

Vista

TM

. Please check ATI

TM

website for driver updates.

1. If a customer incorrectly configures their system they will not see the

performance benefits of CrossFire

TM

. All three CrossFire

TM

components, a

CrossFire

TM

Ready graphics card, a CrossFire

TM

Ready motherboard and

a CrossFire

TM

Edition co-processor graphics card, must be installed

correctly to benefit from the CrossFire

TM

multi-GPU platform.

2. If you pair a 12-pipe CrossFire

TM

Edition card with a 16-pipe card, both

cards will operate as 12-pipe cards while in CrossFire

TM

mode.

Enjoy the benefit of CrossFireEnjoy the benefit of CrossFire

Enjoy the benefit of CrossFire

TMTM

TM

It is recommended to use 500-Watt power supply or greater

to perform the benefit of CrossFire

TM

feature for Radeon

X850XT, X1900 and X1950 series.

Step 1. Remove PCIE Switch card from PCIE2/PCIE SWITCH slot if one is installed.

Step 2. Connect to the system power supply. Please connect a hard disk power

connector to SLI/XFIRE Power connector on this motherboard.

What graphics cards work with CrossFire

TM

?

A complete CrossFire

TM

system requires a CrossFire

TM

Ready motherboard,

a CrossFire

TM

Edition graphics card and a compatible standard Radeon

(CrossFire

TM

Ready) graphics card from the same series, or two CrossFire

TM

Ready cards if they are software enabled. This applies to cards from ATI

TM

or

any of its partners.

Currently, ATI

TM

has released Radeon X850XT, X1800XT, X1900XT, X1950XT,

X1300, and X1600 CrossFire

TM

cards, which require different methods to

enable CrossFire

TM

feature. In the below procedures, we use Radeon

X850XT as the example graphics card. For other CrossFire

TM

cards that

ATI

TM

has released or will release in the future, please refer to ATI

TM

graphics

card manuals for detailed installation guide.

Cards For PCIE2/PCIE SWITCH Slot Cards For PCIE3 Slot

Radeon X1950 Series Radeon X1950 CrossFire

TM

Edition

Radeon X1900 Series Radeon X1900 CrossFire

TM

Edition

Radeon X1800 Series Radeon X1800 CrossFire

TM

Edition

Radeon X1600 Series Radeon X1600 Series

Radeon X1300 Series Radeon X1300 Series

Radeon X850 Series Radeon X850 CrossFire

TM

Edition

1717

17

ASRock ALiveXFire-eSATA2 Motherboard

EnglishEnglish

English

r

e

o

DVI-DMS cable DMS connector

DVI connector

1. You are allowed to install two CrossFire

TM

Edition graphics cards to both slots, or you

may use one CrossFire

TM

Edition graphics cards and a compatible standard Radeon

(CrossFire

TM

Ready) graphics card from the same series.

2. For ATI

TM

Radeon X1300 and X1600 series, there are no CrossFire

TM

Edition graphics

cards. You can still install two regular graphics cards from the same series (two

Radeon X1300 series cards or two Radeon X1600 series cards) on PCIE2/PCIE

SWITCH slot and PCIE3 slot to support CrossFire

TM

. Besides, please connect the

monitor cable to the graphics card on PCIE3 slot.

Step 3. Install the standard Radeon (CrossFire

TM

Ready) graphics card to PCIE2/

PCIE SWITCH slot. For the proper installation procedures, please refer to

section “Expansion Slots”.

Connect the DVI-DMS

cable to DVI connector of

the compatible standard

Radeon (CrossFire

TM

Ready) graphics card.

Standard Radeon

(CrossFire

TM

Ready)

graphics card

Standard Radeon

(CrossFire

TM

Ready)

graphics card

Radeon CrossFire

TM

Edition graphics card

DVI connector

Standard Radeon (CrossFire

TM

Ready)

graphics card

There are two DVI connectors on the

standard Radeon (CrossFire

TM

Ready)

graphics card. Please connect the DVI-DMS

cable to the correct DVI connector; otherwise

, the graphics card will not work.

Step 4. Install the Radeon CrossFire

TM

Edition graphics card to PCIE3 slot. For the

proper installation procedures, please refer to section “Expansion Slots”.

Step 5. Correctly connect the DVI-DMS cable to the monitor connector and two

graphics cards that you install. (If you install two standard Radeon

(CrossFire

TM

Ready) graphics cards to this motherboard, please skip this

step.)

1818

18

ASRock ALiveXFire-eSATA2 Motherboard

EnglishEnglish

English

Step 6. Power on your computer and boot into OS.

Step 7. Remove the ATI

TM

driver if you have any VGA driver installed in your system.

If you install two CrossFire

TM

Edition graphics cards to this motherboard, please

connect one end of DVI-DMS cable to the monitor, another end to DMS of one

of the CrossFire

TM

Edition graphics cards to PCIE3 slot, and the other end to

DVI of another CrossFire

TM

Edition graphics card to PCIE2/PCIE SWITCH slot.

If you install one CrossFire

TM

Edition graphics card and one compatible stan-

dard Radeon (CrossFire

TM

Ready) graphics card to this motherboard, please

connect one end of DVI-DMS cable to the monitor, another end to DMS of the

CrossFire

TM

Edition graphics card, and the other end to DVI of the compatible

standard Radeon (CrossFire

TM

Ready) graphics card.

Connect the DVI-DMS

cable to the monitor

connector.

Connect the DVI-DMS

cable to DMS connector

of the CrossFire

TM

Edition

graphics card.

The Catalyst Uninstaller is an optional download. We recommend using this

utility to uninstall any previously installed Catalyst drivers prior to installation.

Please visit this website for the driver:

http://support.ati.com/ics/support/DLRedirect.asp?

fileIDExt=050553d40196ef109fff37cbb40aaf28&accountID=737&deptID=894

Step 8. Install the required drivers to your system. Please visit the websites below

for installing the drivers that ATI

TM

recommends:

A. ATI

TM

recommends Windows

®

XP Service Pack 2 or higher to be

installed (If you have Windows

®

XP Service Pack 2 or higher installed

in your system, there is no need to download it again):

http://www.microsoft.com/windowsxp/sp2/default.mspx

B. You must have Microsoft .NET Framework installed prior to

downloading and installing the CATALYST Control Center:

http://www.microsoft.com/downloads/details.aspx?

FamilyId=262D25E3-F589-4842-8157-034D1E7CF3A3&displaylang=en

DMS

connector

Radeon

CrossFire

TM

Edition graphics

card

Step 9. Restart your computer.

1919

19

ASRock ALiveXFire-eSATA2 Motherboard

EnglishEnglish

English

t

o

If you install one Radeon CrossFire

TM

Edition graphics card and one compatible

standard Radeon (CrossFire

TM

Ready) graphics card to this motherboard but

not two Radeon CrossFire

TM

Edition graphics cards, please as well follow the

above steps. However, although you have selected the option “Enable

CrossFire

TM

”, the CrossFire

TM

function can not work actually. Your computer

will automatically reboot. After restarting your computer, please confirm whether

the option “Enable CrossFire

TM

” in “ATI Catalyst Control Center” is selected or

not; if not, please select it again, and then you are able to enjoy the benefit of

CrossFire

TM

feature.

Step 12. You can freely enjoy the benefit of CrossFire

TM

feature.

Step 11. Double-click “ATI Catalyst Control Center”. Click “View”, and select “Ad-

vanced View”. Click “CrossFire

TM

”, and then set the option “Enable

CrossFire

TM

” to “Yes”.

Step 10. Install the VGA card drivers to your system, and restart your computer.

Then you will find “ATI Catalyst Control Center” on your desktop.

You will find “ATI Catalyst

Control Center” on your

desktop.

View

CrossFire

TM

Enable CrossFire

TM

* CrossFire

TM

appearing here is a registered trademark of ATI

TM

Technologies Inc., and is used

only for identification or explanation and to the owners’ benefit, without intent to infringe.

2020

20

ASRock ALiveXFire-eSATA2 Motherboard

EnglishEnglish

English

Short Open

2.82.8

2.8

Jumpers SetupJumpers Setup

Jumpers Setup

The illustration shows how jumpers are

setup. When the jumper cap is placed on

pins, the jumper is “Short”. If no jumper cap

is placed on pins, the jumper is “Open”. The

illustration shows a 3-pin jumper whose pin1

and pin2 are “Short” when jumper cap is

placed on these 2 pins.

Jumper Setting

PS2_USB_PW1 Short pin2, pin3 to enable

(see p.2, No. 1) +5VSB (standby) for PS/2 or

USB wake up events.

Note: To select +5VSB, it requires 2 Amp and higher standby current provided by

power supply.

Clear CMOS Jumper

(CLRCMOS1)

(see p.2, No. 11)

Note: CLRCMOS1 allows you to clear the data in CMOS. The data in CMOS includes

system setup information such as system password, date, time, and system

setup parameters. To clear and reset the system parameters to default setup,

please turn off the computer and unplug the power cord from the power

supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3

on CLRCMOS1 for 5 seconds. However, please do not clear the CMOS right

after you update the BIOS. If you need to clear the CMOS when you just finish

updating the BIOS, you must boot up the system first, and then shut it down

before you do the clear-CMOS action.

Clear CMOSDefault

2.7 Surround Display Feature2.7 Surround Display Feature

2.7 Surround Display Feature

This motherboard supports Surround Display upgrade. With the external add-on

PCI Express VGA cards, you can easily enjoy the benefits of Surround Display

feature. For the detailed instruction, please refer to the document at the following

path in the Support CD:

..\ Surround Display Information

Page is loading ...

ASROCK ALIVEXFIRE-ESATA2 R3.0_987 - Owner's manual

This manual is also suitable for

ASROCK ALIVEXFIRE-ESATA2 R3.0_987 - Owner's manual

in other languages

Related papers

Other documents