1
OWNER'S MANUAL
IMPORTANT!
WARRANTY INFORMATION INSIDE. PLEASE READ
FOR INQUIRIES CALL
1800 656 700
OR
WWW.TEAC.COM.AU
50052675-TEAC AK45 IDTV IB-STEREO-3215W-RF-2147 UK-CH-2 SCART-FAV-FSVHS p6527 09 2004 17:411
2
WARRANTY REGISTRATION
Please read this warranty card.
Keep your purchase receipt to enable you to proceed quickly in the event of a Warranty
Service.
Warranty Terms & Conditions
1. TEAC warrants to the original retail purchaser only, that this product is free from
defects in material and workmanship under normal domestic use and
authorises free service during the warranty period at any TEAC Authorised Cen-
tre only. TEAC warranty only applies to products purchased, used and serviced
in Australia.
2. Subject to the terms herein, this warranty effectively covers the equipment as
specified in the Warranty Periods Table from the date of purchase.
3. All parts, except the external cabinet, are warranted as specified in Warranty Pe-
riods Table, and will be repaired or replaced at the sole judgement of TEAC.
4. Normal customer maintenance as described in the owner's manual is not cov-
ered by this warranty (such as cleaning VCR heads etc.)
5. This warranty does not apply to equipment showing abuse, damage or that it
may have been tampered with, altered or repaired outside any TEAC Authorised
Service Centre. If so, the warranty will be void.
*Your nearest Authorised TEAC Service Centre is listed in your Owners Manual
6. In the event that this unit or any defective parts must be returned to TEAC Ser-
vice Centres, a copy of this warranty certificate and of your purchase receipt
must be enclosed to be a valid warranty. Such equipment or parts must be sent
to the nearest authorised TEAC Service Centre. After the repair, the unit will be
available for collection by the owner or it will be returned to the owner. The war-
ranty does not cover freight or insurance. In all cases of in-transit damages or
loss, a claim must be filed against the carrier by the purchaser.
7. In home service will only be provided as part of this warranty if all the following
conditions are met;
a) The product is a Colour Television of 59cm screen size or over.
b) The product is within the warranty period.
c) The product is located within the normal service area of the local
TEAC Service Provider.
In any other situation or circumstance, where an in home service call is
made, a service fee will be charged by the Service Provider. TEAC Total
Care in home service and installation is available at competitive rates.
8. No one is authorised to assume any liability on behalf of TEAC or impose any
obligation on it, in connection with the sale of any equipment other than as
stated in this warranty and outlined above.
9. In no event will TEAC be responsible or liable for indirect or consequential
damages from interrupted operations or other causes.
10. Warranty is not transferable to any subsequent purchaser if the product is sold
during the warranty period,
50052675-TEAC AK45 IDTV IB-STEREO-3215W-RF-2147 UK-CH-2 SCART-FAV-FSVHS p6527 09 2004 17:412
3
Please keep this information for your own records.
Please refer to the owner's manual to ensure that you have followed the correct instal-
lation and operating procedures.
1. Read owner's manual carefully
2. If you require Warranty Service, please contact the TEAC Service Centre
3. Please have your purchase receipt as your proof of purchase and the following de-
tails completed for a valid Warranty.
Owner's Name
Owner's Address
Postcode
Model Name/No. Serial No.
Dealer's Name
Dealer's Address
Postcode
4. Please ensure that your product is packed appropriately upon return to the service
centre.
If you have any other queries regarding service or warranty please contact the
TEAC Service below:
TEAC Total Care Ph: 1800 656 700
Keep this warranty information and your purchase receipt
Your proof of purchase (receipts) will enable fast and efficient service in the event of repair.
WARRANTY PROCEDURES
50052675-TEAC AK45 IDTV IB-STEREO-3215W-RF-2147 UK-CH-2 SCART-FAV-FSVHS p6527 09 2004 17:413
4
Contents
Remote Control ................................ 5
Control Panel ................................... 6
Safety and Precautions .................. 7
Preparation ...................................... 9
Features ........................................ 9
Power connection ....................... 10
Connections to the RF input
socket .......................................... 10
How to connect other devices ..... 10
Inserting batteries in the remote
control handset ........................... 10
Before Switching on your TV ........ 10
Switching the TV ON/OFF .............. 10
To switch the TV on ..................... 10
To switch the TV off ..................... 10
Everyday Operation ....................... 16
MAIN MENU ................................. 16
CHANNEL LIST ........................... 16
NAVIGATING THE WHOLE LIST OF
CHANNELS ................................. 17
INSTALLATION ............................ 18
ADD NEW CHANNELS ............... 18
FIRST TIME INSTALLATION ........ 19
AUDIO SERVICES ....................... 20
CONFIGURATION MENU ............ 20
FAVOURITE MODE ...................... 21
RECEIVER UPGRADE ................ 22
PARENTAL SETTINGS ................ 25
CHANNEL AND MENU
PROTECTION ............................. 27
Advanced Operation ...................... 27
Menu Lock ................................... 28
Program Lock .............................. 29
No Menu ...................................... 30
ELECTRONIC PROGRAM GUIDE
(EPG) ........................................... 30
EDITING THE CHANNEL LIST ... 32
PROGRAMME REMINDERS AND
TIMERS ....................................... 34
RE-INSTALLATION ...................... 37
TV SETUP: ................................... 40
Operating the TV ............................ 41
Operating with the buttons on the TV
set ................................................ 41
Operating with Remote Control .. 41
Menu System ................................. 42
Sound Menu ................................ 42
Picture Menu ............................... 44
Feature Menu .............................. 47
Installation Menu ......................... 48
Program Menu ............................ 49
Other Features............................... 51
TV Status ..................................... 51
Programme Swap (P<P) ............ 51
Double-digit (- -) .......................... 51
Sound Indicator ........................... 52
Picture Mode ............................... 52
Mute Indicator .............................. 52
Volume Bar .................................. 52
AV Modes ..................................... 52
To operate Teletext ...................... 53
To select a page of Teletext ......... 53
Teletext ........................................... 53
To Select Index Page .................. 53
To Select Teletext with a TV
Programme ................................. 53
Searching for a page while watching
TV ................................................ 53
To Select Double Height Text ...... 53
To Reveal concealed
Information .................................. 53
To Stop Automatic Page Change 54
To Select a Subcode Page ......... 54
To exit Teletext ............................. 54
To Display the Time .................... 54
Fastext ......................................... 54
Connect Peripheral Equipment .... 55
Via the Euroconnector ................. 55
YCbCr Mode ................................ 55
RGB Mode ................................... 55
Via Ant Input ................................. 55
Decoder....................................... 55
TV and Video Recorder ............... 55
Playback NTSC ........................... 55
Copy Facility ................................ 55
Search for and store the test
signal of the video recorder ........ 55
Camera and Camcorder ............ 56
To connect to S-VHS input .......... 56
Connect the decoder to the video
recorder ....................................... 56
Connecting Headphones ........... 56
Antenna Connections .................... 57
On TV mode ................................ 58
On Digital mode .......................... 58
50052675-TEAC AK45 IDTV IB-STEREO-3215W-RF-2147 UK-CH-2 SCART-FAV-FSVHS p6527 09 2004 17:414
5
remote control
50052675-TEAC AK45 IDTV IB-STEREO-3215W-RF-2147 UK-CH-2 SCART-FAV-FSVHS p6527 09 2004 17:415
6
Speakers (left + right)
= Power On / Off
- + = Volume -/+
- P/Ch + = Program -/+
MENU = Menu
AUDIO L ( ) = Audio left
AUDIO R ( ) = Audio right
VIDEO ( )= VCR
H-PHONE ( ) = Headphone 3,6 mm Ø
SVHS
ANT = Antenna (75 W)
EXT.1 = Scart Socket 1 (RGB)
EXT.2 = Scart Socket 2 (YCbCr)
Power Cable
Box
Control Panel
50052675-TEAC AK45 IDTV IB-STEREO-3215W-RF-2147 UK-CH-2 SCART-FAV-FSVHS p6527 09 2004 17:416
7
Safety and Precautions
To ensure safe and reliable operation of the TV set, please observe the following
precautions in installation, operation and maintenance.
Attention:
1. Pay attention to the power supply cord before installing the TV set. Do not hang
anything on the cord, and avoid treading on the cord.
2. The slots on the housing back are designed for ventilation to ensure reliable
operation of the TV set and prevent overheating. They must never be covered or
blocked. The TV set must not be placed near a heat source or it might be dam-
aged.
3. The outdoor antenna must not be erected close to HV lines or other power
supply lines. Use extreme care when erecting the antenna and not to touch
living wires or injury may occur.
4. This TV set can only use the supply voltage and frequency indicated on the
back of the housing. If your power supply does not comply with them, please
consult with the service personnel.
5. Do not let any object fall into the ventilation openings of the TV set housing, nor
let any liquid flow into the machine via the openings.
6. Do not subject the TV set to rain, or use it in a damp environment. When clean-
ing dust, be sure to remove the power supply plug from its socket first. Do not
clean the housing directly with liquid detergent, use a damp cloth. Be sure to
remove the power supply plug from its socket and remove the antenna plug
during a thunderstorm or when it will not be used for long time, to avoid com-
ponents being damaged by lightning.
7. If you use an indoor antenna, do not let it touch any electrical appliance, or
normal reception of TV programs may be affected.
50052675-TEAC AK45 IDTV IB-STEREO-3215W-RF-2147 UK-CH-2 SCART-FAV-FSVHS p6527 09 2004 17:417
8
Safety:
1. Do not remove the back of housing by yourself, as high voltages inside the
unit are dangerous. If it is necessary to open the back, ask a technician with
specialized service experience.
2. Remove the power supply plug from its socket in case of the following condi-
tions, and consult with service personnel.
(1) The power cord or plug are damaged or shows cracking.
(2) Any object has fallen into or liquid flown into the TV set.
(3) The performance of TV set has deteriorated significantly or there is
damage on the housing.
(4) The TV set will not operate normally according to the instructions.
3. Please remove the power supply plug from its socket when the TV set will not
be used for a long period of time.
Instructions for waste disposal:
Packaging and packaging aids are recyclable and should principally be re-
cycled. Packaging materials, such as foil bag, must be kept away from chil-
dren.
Batteries, including those which are heavy metal-free, should not be disposed
of with household waste. Please dispose of used batteries in an environmen-
tally sound manner. Find out about the legal regulations which apply in your
area.
DO NOT LEAVE YOUR TV AT STAND-BY OR OPERATING WHEN YOU LEAVE
YOUR HOUSE
Safety Precautions
50052675-TEAC AK45 IDTV IB-STEREO-3215W-RF-2147 UK-CH-2 SCART-FAV-FSVHS p6527 09 2004 17:418
9
Preparation
CAUTION
RISK OF ELECTRIC
SHOCK
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the
user to the presence of uninsulated "dangerous
voltage" within the product's enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock of persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
Dear Customer:
Thank you for purchasing our latest TV
set.
Please read this instruction manual
carefully first before operation so that
you can use it in a safe and reliable
manner and bring all its functions into
full play. Please also keep it properly
for future reference.
Preparation
For ventilation, leave a space of at least
10 cm free all around the set. To prevent
any fault and unsafe situations, please
do not place any objects on top of the
set.
Use this apparatus in tropical and/or
moderate climates.
Features
It is a remote controlled colour television.
100 programmes from VHF, UHF bands
or cable channels can be preset.
It can tune cable channels.
Controlling the TV is very easy by its menu
driven system.
It has two Euroconnector sockets for ex-
ternal devices.
German sound system is available.
Full function Teletext (Fastext).
It is possible to connect headphone.
Direct channel access.
APS Plus (Automatic Programming Sys-
tem).
All programmes can be named.
Programme swapping between last
watched two programmes.
Forward or backward automatic tuning.
Sleep timer.
Child Lock.
Automatic sound mute when no transmission.
When no valid signal is detected, after 5 min-
utes the TV switches itself automatically to
stand-by mode.
WSS (Wide Screen Signaling).
NTSC Playback.
YCbCr Mode.
VCR Mode.
Front AV (FAV) is available.
SVHS (SVHS connector)
50052675-TEAC AK45 IDTV IB-STEREO-3215W-RF-2147 UK-CH-2 SCART-FAV-FSVHS p6527 09 2004 17:419
10
Before Switching on your TV
Power connection
IMPORTANT: The TV set is designed to
operate on 240 V AC, 50 Hz.
After unpacking, allow the TV set to reach
the ambient room temperature before
you connect the set to the mains.
Connections to the RF input
socket
Connect the aerial or cable TV plug to
the RF input socket located at the back
of the TV and connect the cable plug
coming out from the TV out socket lo-
cated at the devices (VCR, DVB etc.) to
this socket as well.
How to connect other devices
IMPORTANT: Switch off the TV before con-
necting any external device.
Sockets for external connections are on
the back of the TV.
For connection of other devices via Euro-
connector refer to the manuals of the re-
lated devices.
Inserting batteries in the remote
control handset
Remove the battery cover located on the
back of the handset by gently pulling up-
wards from the indicated part.
Insert two AAA (R03) or equivalent type
batteries inside.
Replace the battery cover.
NOTE: Remove batteries from remote
control handset when it is not to be
used for a long period.Otherwise it can
be damaged due to any leakage of bat-
teries.
Switching the TV ON/OFF
You can operate your TV either using
the remote control handset or direct-
ly using the TV onset buttons.
To switch the TV on
Your TV will switch on in two steps:
1- Press the POWER button located on
the front of the TV. Then the TV switch-
es itself to standby mode and the LED
located below becomes RED.
2- To switch on the TV from stand-by
mode either:
Press a digit key on the remote control
so that a programme number is se-
lected,
or,
Press Programme Up and Down but-
tons on the front of the TV or on the re-
mote control respectively, so the TV will
switch on and the RED Led will turn off.
To switch the TV off
Press the stand-by key on the remote
control, so the TV will switch to stand-
by mode and the LED will become
Red, or,
Press the POWER button located on
the front of the TV, so the TV will
switch off.
50052675-TEAC AK45 IDTV IB-STEREO-3215W-RF-2147 UK-CH-2 SCART-FAV-FSVHS p6527 09 2004 17:4110
11
TUNING IN
Your TV will switch on in the digital mode. Because this is the first time that
the TV has been used, there are no channels stored in the memory and the
First Time Installation menu is displayed on the screen.
preparation
SILENCE MODE:
"When you turn off your IDTV by pressing Stand-by key (on RC) , IDTV switches into
SILENCE mode and the led on the front of IDTV starts blinking.
In the silence mode IDTV searches for a new software. If a new software is found, it is
loaded onto the old s/w without any warning message. TV enters to stand-by mode
after loading process. Also, software update is done automatically everyday at 4:00
am.
You can terminate silence mode any time you want by pressing P+/P - or
numeric keys.
Press OK button to start Installation.
The following menu comes to the screen. Using the
or keys on the
remote control, make sure that the YES button is highlighted in yellow, and
press the SELECT key to start the automatic search.
50052675-TEAC AK45 IDTV IB-STEREO-3215W-RF-2147 UK-CH-2 SCART-FAV-FSVHS p6527 09 2004 17:4111
12
The TV will automatically tune to VHF transmission channels 2 to 12
and UHF transmission channels 28 to 69 looking for digital terrestrial TV
broadcasts and displaying the names of the channels found. This pro-
cess will take about three minutes.
After Automatic search is finalized the following menu appears.
50052675-TEAC AK45 IDTV IB-STEREO-3215W-RF-2147 UK-CH-2 SCART-FAV-FSVHS p6527 09 2004 17:4112
13
preparation
HINT
Depending on the reception conditions
in your particular area, you may find
that the list of channels found includes
one or more repeated names. This is
because the TV may detect and store
some channels, including those it can-
not receive clearly, from adjacent areas
alongside the strong channels from a
transmitter nearby. This is not a prob-
lem and the weaker channels can be
deleted from the TV later, as described
in ADVANCED OPERATION - Editing
the channel list section.
If no digital terrestrial television
broadcasts are found the TV will
display a message:
You should then refer to the Tips/
Troubleshooting Guide to establish
the cause of the problem.
If you select Yes
After A.P.S. is completed program table is displayed on the screen.
See the Programming menu in terrestrial TV section.
If you select No, the first channel of the channel list is displayed you
can now watch digital terrestrial television, selecting the channel you
require as described in the next section.
50052675-TEAC AK45 IDTV IB-STEREO-3215W-RF-2147 UK-CH-2 SCART-FAV-FSVHS p6527 09 2004 17:4113
14
everyday operation
There are a great many keys to use in different situations. Many of the menu
screens displayed by the TV have reminders as to which keys do what, at the base
of the screen. In addition, many screens have further help available which is dis-
played when the INFO key is pressed, as prompted at the bottom right of the
screen.
Pressing the TV/DTV key at any time while watching television programmes will
switch the TV set between displaying the digital terrestrial television programme and
its normal analogue television reception.
CHANGING CHANNELS
Hint
The LCN numbers are assigned
by the broadcasters. Because
not all channels are broadcast
and stored by the TV, the chan-
nel list numbers do not run con-
tinuously.
The fifteenth channel in the list,
for example, may not be channel
number 15 but channel number
17.
When you press a number key on
the remote control, a small box ap-
pears in the top left of the screen to
show the entered number. After
each digit is entered, the TV will wait
up to two seconds for the next digit
to be pressed until either three dig-
its have been entered or you do not
press a digit in time. The channel
corresponding to the entered num-
ber in the box will then be selected.
CHANGING CHANNELS
You can select the channel you wish to watch in one of four ways - stepping
through the channel list, selection by number, from the on-screen channel list, and
using the electronic programme guide (EPG).
To move through the channel list, press the P+ or P - keys on the remote
control. Pressing the P+ key will select the channel next in the channel list. Press-
ing the P - key will select the previous channel in the list.
Pressing the P+ key when the last channel in the list is being viewed will select
the first channel. Similarly, pressing the P - key when the first channel is dis-
played will select the last channel in the channel list.
You can also select the required channel by directly using its channel sort number.
Your TV has two kinds of channel sorting mechanism. Name (Alphabetical) list and
LCN sort.
In alphabetical sort, all stored channels are ordered according to their name, i.e.
letter A first, Z last. In this mode channel list numbers are continuous, and entering
a number using the remote control will directly remove you to that channel. Also
entering a number greater than the number of stored channels will select the last
channel.
Other type of channel sorting mechanism is LCN sort. LCN is the unique number
for every channel in network which is assigned by the broadcaster, to establish a
logical connection between the channel and network. In this sorting mode LCN
number must be entered to select a channel.
50052675-TEAC AK45 IDTV IB-STEREO-3215W-RF-2147 UK-CH-2 SCART-FAV-FSVHS p6527 09 2004 17:4114
15
everyday operation
Hint
Not all channels broadcast the
programme data. If the name and
times of the programme is not
available then No Event Informa-
tion is displayed in the information
banner.
The information banner gives a
number of facts on the channel se-
lected and the programs on it.
-Channel number or LCN (logical
channel number) number accord-
ing to current sorting mode
-Name of the channel
-Name of the current Network
-Current Time and Date
-A bar indicating current level of sig-
nal
-Current event name, next event
name, their start and end times,
their types and parental ratings
While watching TV by pressing the
INFO key, you can see a more de-
tailed info banner at the bottom of
the screen. In this banner, in addi-
tion to channel information, you can
also see extended event informa-
tion of current and next event.
Many icons are displayed in the
information banner. These are;
-Favourite icon indicating that cur-
rent channel is set as favorite (if
the channel is not set as favourite
the field is left empty)
-Dolby Sound (AC3) icon (if the
channel has not Dolby Digital Au-
dio the field is left empty)
-Lock icon indicating that current
channel is locked. (if the channel
is not locked the field is left empty)
- Teletext icon indicating that the
channel has Teletext or not. (if the
channel has not Teletext service
the field is left empty)
-TV or Radio icon depending on
the current type of channel.
-Aerial icon.
locked channel
favourite channel
INFORMATION BANNER
Whenever you change channel, using the P+ and P - keys or the number
keys, the TV display the channel picture along with an information banner at
the bottom of the screen. This will remain on the screen for approximately
four seconds.
If the selected channel is locked
(see Advanced operation- Chan-
nel protection), you must enter the
correct four digit code to view the
channel.
Alternatively, the P+ or P- keys
are used to move to another, un-
locked channel.
50052675-TEAC AK45 IDTV IB-STEREO-3215W-RF-2147 UK-CH-2 SCART-FAV-FSVHS p6527 09 2004 17:4115
16
everyday operation
CHANNEL LIST
Using the or keys on the remote control in the Main menu,
make sure that the first item, Channel List, is highlighted in yellow and
press the SELECT key, to display the channel list.
The following operations can be performed in this menu:
1. Navigating the whole list of channels
2. Moving channels up/down
3. Renaming channels
4. Adding locks to channels
5. Favourites
Channel table is the place where the channels are managed.
Press
or keys to select the various options for managing the chan-
nels lists.
MAIN MENU
The Main Menu is accessed, pressing
the MENU key. The items accessed
through the Main Menu are:
1. Channel List
2. Installation
3. Configuration
4. Timers
5. TV Setup
50052675-TEAC AK45 IDTV IB-STEREO-3215W-RF-2147 UK-CH-2 SCART-FAV-FSVHS p6527 09 2004 17:4116
17
everyday operation
NAVIGATING THE WHOLE LIST OF CHANNELS
In the channel table
or keys serves for moving the focus to the previous
or next channel,
or keys for page up and page down.
To watch a specific channel highlight it using
or keys then press SE-
LECT key while the Select button is highlighted. Then the name and number of
the selected channel will be displayed in the top-right corner of the screen.
If the selected channel is password protected then a pop up menu is displayed. If
the correct code is entered then the selected channel can be watched. Also you
can select another channel by navigating with
or keys.
The scroll Bar in middle of the screen shows relative position of the currently visi-
ble channels with respect to the whole list.
MOVING CHANNELS
Reordering the list can be done by moving programs one by one to new posi-
tions. In order to do a move, the Move button is highlighted on the screen using
or keys. A program move is then performed by pressing SELECT key,
the colour of the program will be changed to red. In this state, press
or
keys to move the program to the desired location within the list. Once you are
satisfied with the position of the program press SELECT key to finalize moving
program.
RENAMING CHANNELS
To rename a specific channel, the name must be highligthed (use
or
keys) and then select the Edit Name option (use
or keys). Press
SELECT to activate the rename feature. Following the previous procedure, the
name appears on the right side of the menu with the first character highlighted.
Now
/ moves to the previous/next character. / toggles the cur-
rent character, i.e., b character becomes a on
and c on . Pressing
the numeric keys 0...9 replaces the highlighted character with the characters
printed above the key one by one as the key is pressed.
Press the MENU key to cancel the editing and SELECT saves the new name.
ADDING LOCKS TO CHANNELS
Channel Locking provides a password-protected access to channels selected by
parents. In order to lock a channel you should know the Parental Lock password
(default value is set to 0000 in the factory and can only be changed from the Con-
figuration Menu). Select the channel to be locked by highlighting it and select the
Lock option. When SELECT key is pressed a password box is displayed.
Enter the parental Lock code you wish to use followed by pressing SELECT key.
The Lock icon
will now be displayed in front of the selected channel. Repeat
the same operation to cancel the Lock.
50052675-TEAC AK45 IDTV IB-STEREO-3215W-RF-2147 UK-CH-2 SCART-FAV-FSVHS p6527 09 2004 17:4117
18
SETTING FAVOURITES
You can set various channels as favourites so that only the favourite channels
are navigated. To set a favourite you should highlight the Favourites option at
bottom of the channel table and also you should highlight a channel which you
want to add to the favourites list. Then press SELECT key and a smiling face
icon
will appear on right ride of channel name. This means that channel is
now one of your favourites. To remove any channel from favourites list just do
the same thing. To activate favourites go to configuration menu and turn on the
favourite option. To cancel the favourites go to configuration menu and turn off
the favourite option.
INSTALLATION
The Installation menu mainly intends to help you for building a Channel Table into your
receiver in most efficient way.
This menu includes:
1. Add New Channels,
2. First Time Installation
ADD NEW CHANNELS:
This tuning menu consists of two parts;
· Automatic Search
· Manual Search
Automatic Search:
Automatic search is started by pressing SELECT key in the auto-search pop
up menu. All the services are searched and a channel table is created
automatically.
All channels found are stored in a sorted form with respect to their channel
numbers. Some services may not appear with the correct channel number. At
the time of printing, not all broadcasters are sending their channel number
information.
Manual Search:
In manual search the number of the multiplex is entered manually and only that
multiplex is searched for the channels. For every valid channel number, signal
level, signal quality and network name are shown at the bottom of the screen.
In both manual and auto search any existing channel in the database is not re-
stored to avoid redundant duplicates of that channel.
50052675-TEAC AK45 IDTV IB-STEREO-3215W-RF-2147 UK-CH-2 SCART-FAV-FSVHS p6527 09 2004 17:4118
19
FIRST TIME INSTALLATION
The user can use this item to load default settings, which had been loaded to
the receiver at the factory. To install factory settings, highlight First Time Instal-
lation menu and press SELECT key, then you will be asked to confirm for de-
leting all channels and settings. Selecting YES by pressing SELECT key and
the existing channel table will be deleted.
After factory settings loaded First Time Installation menu is displayed.
Pressing SELECT key will display the Automatic Search Menu and you will be
asked for starting the automatic search for all available channels. Automatic
Search will be started by highlighting YES and pressing SELECT key. When
Automatic Search is finished or cancelled receiver returns to viewing window.
50052675-TEAC AK45 IDTV IB-STEREO-3215W-RF-2147 UK-CH-2 SCART-FAV-FSVHS p6527 09 2004 17:4119
20
CONFIGURATION MENU
The Configuration menu screen is accessed from the Main Menu. Press the
MENU key to display the Main Menu and the
key twice to highlight Config-
uration, then press SELECT key to display the Configuration menu screen.
Press MENU or EXIT key to leave the menu.
The various configuration functions are displayed in a list, along with a
quarter-screen image of the currently selected channel. You can select a
function by highlighting the corresponding menu line with the
or
keys. There are seven configuration functions.
Configuration Menu includes the following main items:
· Audio Service
· Favourite Mode
· Receiver Upgrade
· Parental Settings
· Date/Time Settings
· System Info
AUDIO SERVICES
Highlight the Audio Services line in the Configuration menu and use the or
keys to cycle through the service options. This button is used to change
audio service. When Dolby Audio is available for the channel, pressing
or
keys will switch the audio service. Otherwise audio service is English as default.
Changes will be updated while exiting Configuration Menu. Last Audio Service type
will be saved for every channel.
Return to normal TV viewing by pressing the MENU key.
"No Analog audio is available when Dolby selected."
By pressing YELLOW key, current audio output will change between Stereo,
Left, Right and Dolby. Last selected audio type will be saved for current chan-
nel.
or
50052675-TEAC AK45 IDTV IB-STEREO-3215W-RF-2147 UK-CH-2 SCART-FAV-FSVHS p6527 09 2004 17:4120
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
