Extron DVI 101 Owner's manual

DVI 101
Extron
Brand
Extron
Model
DVI 101
Category
Video splitters
Type
Owner's manual

This manual is also suitable for

Extron DVI 101 extends DVI and HDMI signals beyond the specified cable limits of 15' (5 m). Ideal for long cable runs, it recovers and retransmits the signal, allowing for reliable transmission up to 200' (61 m) at the highest transmission rate of 165 MHz. The DVI 101 supports resolutions up to 1920x1200, including 1080p, and features a status LED to indicate power and input signal presence. It can be powered from the source device or an external power supply.

Extron DVI 101 extends DVI and HDMI signals beyond the specified cable limits of 15' (5 m). Ideal for long cable runs, it recovers and retransmits the signal, allowing for reliable transmission up to 200' (61 m) at the highest transmission rate of 165 MHz. The DVI 101 supports resolutions up to 1920x1200, including 1080p, and features a status LED to indicate power and input signal presence. It can be powered from the source device or an external power supply.

3. Connect the display device to the output connector on the DVI/HDMI 101 rear panel. For
long cable runs, position the equalizer as close as possible to the display end of the cable —
no more than 15' (5 m) from the display.
4. If using the provided external power supply, connect it to the 2-pole captive screw connector
on the DVI/HDMI 101 rear panel.
N For shorter distances, the DVI/HDMI 101 can receive power from the input device. See
the table on the other side of this card for the maximum distances at which the
DVI/HDMI 101 can be powered from the source for each resolution.
DVI Source
Long
Input Cable
( 3’ - 200’ )
Short
Input Cable
( < 15’ )
Display
DVI/HDMI 101
D
ispla
y
Status LED
The Status LED on the front
panel lights as follows:
Yellow – Unit receiving power
Green – Input signal present
DVI 101 and HDMI 101 Installation Guide, cont’d
DVI-D INPUT
Application diagram for a DVI 101
The DVI 101 and HDMI 101 Cable Equalizers extend
DVI and HDMI signals beyond the specified cable limits
of 15' (5 m). They should be installed at the end of long
cable runs; the cable from the DVI/HDMI 101 output to
the display input should be no longer than 15' (5 m). To
install either of the equalizers,
1. Mount the DVI/HDMI 101.
2. Plug a DVI or HDMI input device into the input connector on the DVI/HDMI 101 front
panel.
• ThemaximuminputcablelengthtotheDVI/HDMI101is200'(61m)forthehighest
transmissionrateof165MHz.
• The table below shows the maximum cable lengths for each resolution, depending on
whether the equalizer is powered by the external power supply or by the source device.
Video resolution
Powered from source
Powered from external
power supply
640x480,480p
150'(46m) 275'(84m)
1024x768,1280x1024,720p,1080i
150'(46m) 250'(76m)
1600x1200,1920x1200,1080p 125'(38m) 200'(61m)
N
Avoid using couplers and adapters between cables, as this can cause signal degradation.
DVI 101 and HDMI 101 Installation Guide
68-1664-01 Rev A 01 09
www.extron.com
Extron Electronics, Anaheim, CA
Laptop w/
DVI Output
Projector
Extron
DVI 101
Equalizer
Long DVI Cable
200’ (61 m) Max.
Short DVI Patch
Cable
POWER
12V
0.4A MAX
DVI 101
DVI-D OUTPUT
  • Page 1 1

Extron DVI 101 Owner's manual

DVI 101
Extron
Brand
Extron
Model
DVI 101
Category
Video splitters
Type
Owner's manual
This manual is also suitable for

Extron DVI 101 extends DVI and HDMI signals beyond the specified cable limits of 15' (5 m). Ideal for long cable runs, it recovers and retransmits the signal, allowing for reliable transmission up to 200' (61 m) at the highest transmission rate of 165 MHz. The DVI 101 supports resolutions up to 1920x1200, including 1080p, and features a status LED to indicate power and input signal presence. It can be powered from the source device or an external power supply.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents