CAB Series 600, 700, 800 Assembly Instruction

CAB
Brand
CAB
Model
Series 600, 700, 800
Type
Assembly Instruction

This manual is also suitable for

Step Description
1. Attach the fixed rack wall (2) to the ground plate (1) using two
phillips head srews M5 x 16 from below, (bolting torque 5 Nm).
2. Attach the two aluminum profiles (5) to the ground plate (1) using
two phillips head srews M5 x 16 from below, (bolting torque 5 Nm).
3. Mount the moveable rack wall (3) with the aluminum U-channels
to the ground plate by pushing the U-channels into the spindle
nuts (6) until fully seated.
4. Position the top plate (4) identical to the ground plate (1) so that
the red knurled head is on the same side as the fixed rack wall.
5. Attach the top plate (4) to the aluminum profiles using four
phillips head srews M5 x 16.
6. Remove the styrofoam fixing pieces under the four spindle
nuts (6).
7. Attach the tightener pulley (8) to the fixed rack wall (2) with a
phillips head srew M4 x 12, a ratched wheel and a washer
losely.
8. Push the four gear wheels (7) on the four spindles.
9. Put the gear belt over the four gear wheels (7) and the tightener
pully (8) and also under the width adjustment lock (9).
10. Tighten the gear belt with tightener pulley (8). Tighten also the
phillips head srew M4 x 12.
11. Fix the gear belt with the knurled head screw of the width
adjustment lock (9).
12. Get the moveable rack wall (3) parallel to the fixed rack wall (2)
by turning the single spindels.
13. Put the four clamp hoops on the gear wheels (7) and
tighten them up.
14. Losen the the knurled head screw of the width adjustment lock (9).
15. By pulling the gear belt make shure the magazine moves freely.
16. Check the parallelism.
Picture 1
Picture 3
Pos. 9:
Knurled head
screw for width
adjustment lock
Pos. 7:
Gear wheels with
clamp hoops
Pos. 2:
Fixed rack wall
with aluminium profile
Pos. 8:
Tightener pulley
Pos. 7:
Gear wheels with
clamp hoops
Stackable *1
Stackable *2
for Reversible
Pos. 5:
Aluminium profile
Pos. 3:
Moveable rack wall
Pos. 1:
Ground plate without
adjustment lock
Pos. 1:
Ground plate without
knurled head screw
Pos. 5:
Aluminium profile
Pos. 5:
Aluminium profile
Pos. 6:
Spindle nut
Pos. 2:
Fixed rack wall
with aluminium
profil
Picture 2
Picture 3
*1 = 704-706,
708-719
*2 = 707
Pos. 4:
Top plate with knurled
head screw (red)
and adjustment lock
Copyright bei cab/ 9009025/ Status 12/2014
Notes
Fixed rack wall (2) : Positioning stripes
No. 1 is down, No. 50 is up
Position see picture 2 (top view)
Moveable rack wall (3): Positioning stripes No. 1
is down, No. 50 is up. Take care that the softend
corners of the spindle nuts (6) shows upwards.
Width adjustment lock (9) shows to the fixed
rack wall (2)
Position see picture 2. For reversible use
replace the plastic plate top (picture 3)
First put the ratched wheel, than the washer
on the screw. Tightener pulley shows down,
long hole up.
Flat front side of the gear wheels (7) up to
limited stop
Adjust the slot of the clamp hoops horizontal
and with the opening showing inwards, screw
heads must be reachable.
If it moves hardly - losen the gear belt
(Step 9)
If the rack walls are not parallel - lose all clamp
hoops (7) and repeat step 11 to 16.
Final Assembly PCB Magazine
704 - 706, 708 - 709, 715 - 719
  • Page 1 1

CAB Series 600, 700, 800 Assembly Instruction

CAB
Brand
CAB
Model
Series 600, 700, 800
Type
Assembly Instruction
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents