Edge-Core ECS2100-28PP User manual

www.edge-core.com

Web Management Guide

ECS2100-10T/PE/P

ECS2100-28T/P/PP

10/28-Port Web-Smart Pro

Gigabit Ethernet Switch

Software Release v1.2.2.24

Web Management Guide

ECS2100-10T Gigabit Ethernet Switch

Web-smart Pro Gigabit Ethernet Switch

with 8 10/100/1000BASE-T (RJ-45) Ports

and 2 Gigabit SFP Ports

ECS2100-10PE Gigabit Ethernet Switch

Web-smart Pro Gigabit Ethernet Switch

with 8 10/100/1000BASE-T (RJ-45) 802.3 af/at PoE Ports

with 2 Gigabit SFP Ports (PoE Power Budget: 65W)

ECS2100-10P Gigabit Ethernet Switch

Web-smart Pro Gigabit Ethernet Switch

with 8 10/100/1000BASE-T (RJ-45) 802.3 af/at PoE Ports

and 2 Gigabit SFP Ports

(PoE Power Budget: 125 W)

ECS2100-28T Gigabit Ethernet Switch

Web-smart Pro Gigabit Ethernet Switch

with 24 10/100/1000BASE-T (RJ-45) Ports

and 4 Gigabit SFP Ports

ECS2100-28P Gigabit Ethernet Switch

Web-smart Pro Gigabit Ethernet Switch

with 24 10/100/1000BASE-T (RJ-45) 802.3 af/at PoE Ports

and 4 Gigabit SFP Ports

(PoE Power Budget: 200 W)

ECS2100-28PP Gigabit Ethernet Switch

Web-smart Pro Gigabit Ethernet Switch

with 24 10/100/1000BASE-T (RJ-45) 802.3 af/at PoE Ports

and 4 Gigabit SFP Ports

(PoE Power Budget: 370 W, can extend to 740 W)

E102019-CS-R06

– 3 –

How to Use This Guide

This guide includes detailed information on the switch software, including how to

operate and use the management functions of the switch. To deploy this switch

effectively and ensure trouble-free operation, you should first read the relevant

sections in this guide so that you are familiar with all of its software features.

Who Should Read

this Guide?

This guide is for network administrators who are responsible for operating and

maintaining network equipment. The guide assumes a basic working knowledge of

LANs (Local Area Networks), the Internet Protocol (IP), and Simple Network

Management Protocol (SNMP).

How this Guide

is Organized

This guide provides detailed information about the switch’s key features. It also

describes the switch’s web browser interface. For information on the command line

interface refer to the CLI Reference Guide.

The guide includes these sections:

◆ Section I “Getting Started” — Includes an introduction to switch management,

and the basic settings required to access the management interface.

◆ Section II “Web Configuration” — Includes all management options available

through the web browser interface.

◆ Section III “Appendices” — Includes information on troubleshooting switch

management access.

This guide focuses on switch software configuration through the web browser.

For information on how to manage the switch through the command line interface,

see the following guide:

CLI Reference Guide

Note:

For a description of how to initialize the switch for management access via

the CLI, web interface or SNMP, refer to “Initial Switch Configuration” in the CLI

Reference Guide.

How to Use This Guide

– 4 –

For information on how to install the switch, see the following guide:

Installation Guide

For all safety information and regulatory statements, see the following documents:

Quick Start Guide

Safety and Regulatory Information

Conventions The following conventions are used throughout this guide to show information:

Note:

Emphasizes important information or calls your attention to related features

or instructions.

Documentation

Notice

This documentation is provided for general information purposes only. If any

product feature details in this documentation conflict with the product datasheet,

refer to the datasheet for the latest information.

Revision History This section summarizes the changes in each revision of this guide.

Revision Date Change Description

v1.2.2.24 10/2019 Updated:

◆

Usage guidelines in "LBD Configuration" on page 406

◆

Command usage in "Saving Power" on page 131

◆

Note in Multicast Filtering "Overview" on page 411

◆

Note in "Copying Files via FTP/SFTP/TFTP or HTTP" on page 72

◆

Note in "Saving the Running Configuration to a Local File" on

page 75

◆

Command usage in "Configuring Local Port Mirroring" on

page 133

◆

Note about MAC/PHY TLV setting in "Configuring LLDP

Interface Attributes" on page 337

◆

Command usage in "Specifying Static Interfaces for a Multicast

Router" on page 418

◆

Command usage in "Specifying Static Interfaces for an

IPv6 Multicast Router" on page 443

◆

Added TR-101 description under "DHCP Snooping Global

Configuration" on page 309

◆

Receiver timeout in "Configuring sFlow Receiver Settings" on

page 139

◆

Default settings in "DoS Protection" on page 304

◆

Rate limit range in "Creating QoS Policies" on page 219

◆

"Specifying NTP Time Servers" on page 85

v1.2.2.15 01/2019 Removed mention of GVRP support

How to Use This Guide

– 5 –

v1.2.2.15 07/2018 Updated:

◆

"Configuring a Dynamic Trunk" on page 124

◆

"Adding Static Members to VLANs" on page 152

Added

◆

"Configuring DHCP Relay Agent Mode" on page 528

◆

"Configuring DHCP L2 Relay Service" on page 529

◆

"Configuring DHCP L3 Relay Service" on page 533

◆

"Configuring DHCPv6 Relay Service" on page 535

v1.2.2.9 06/2018 Multiple inaccuracies and parameter descriptions added and

removed per internal audit.

v1.2.2.9 05/2018 Document Corrections

Updated:

◆

Command Usage - updated bullet text and ACL limits "Access

Control Lists" on page 272

◆

"Configuring Static Routes" on page 496

Removed:

◆

Egress option setting from "Showing ACL Hardware Counters"

on page 289

◆

Unsupported “dot1agCfm” traps from table "Supported

Notification Messages" on page 369

v1.2.2.9 09/2017 New:

◆

"Configuring the Routing Information Protocol" on page 500

Removed:

Ethernet Ring Protection Switching (ERPS)

v1.2.2.0 01/2017 New:

◆

"Automatic Operation Code Upgrade" on page 77

◆

"Saving Power" on page 131

◆

"Sampling Traffic Flows" on page 139

◆

"Mapping CoS Priorities to Per-hop Behavior" on page 211

◆

"Mapping DSCP Priorities to Per-hop Behavior" on page 212

◆

"Setting the Switch’s Overall PoE Power Budget" on page 355

◆

"Switch Clustering" on page 398

◆

"LBD Configuration" on page 406

◆

"Displaying MLD Snooping Statistics" on page 448

◆

"IP Tools" on page 463

Revision Date Change Description

How to Use This Guide

– 6 –

Updated:

◆

Table 3, "Web Page Configuration Buttons," on page 48

◆

Table 4, "Switch Main Menu," on page 50

◆

"Displaying Hardware/Software Versions" on page 69

◆

"Managing System Files" on page 72 – SFTP

◆

"Sampling Traffic Flows" on page 139

◆

"Configuring VLAN Groups" on page 149

◆

"Storm Control" on page 202

◆

"Mapping CoS Priorities to Per-hop Behavior" on page 211

◆

"Mapping DSCP Priorities to Per-hop Behavior" on page 212

◆

"Creating QoS Policies" on page 219

◆

"Configuring Global Settings for Network Access" on page 255

◆

"Web Authentication" on page 250

◆

"Configuring Network Access for Ports" on page 256

◆

"DoS Protection" on page 304

◆

"DHCP Snooping Global Configuration" on page 309

◆

"Configuring Ports for DHCP Snooping" on page 312

◆

Table 26, "Supported Notification Messages," on page 369

◆

"Setting the Port PoE Power Budget" on page 357

◆

"Setting the Switch’s IP Address (IP Version 4)" on page 471

◆

"Configuring the IPv6 Default Gateway" on page 476

◆

"Configuring IPv6 Interface Settings" on page 476

◆

"Displaying the Routing Table" on page 497

◆

"Multicast Domain Name Service" on page 525

◆

"Configuring DHCP L3 Relay Service" on page 533

Removed:

◆

Mapping Ingress DSCP Values to Internal DSCP Values

◆

Mapping CoS Priorities to Internal DSCP Values

◆

Application Filter

v1.1.2.0 1/2016 Initial release

Revision Date Change Description

– 7 –

Contents

How to Use This Guide 3

Contents 7

Figures 17

Tables 29

Section I Getting Started 31

1 Introduction 33

Key Features 33

Description of Software Features 34

Configuration Backup and Restore 34

Authentication 34

Access Control Lists 35

Port Configuration 35

Rate Limiting 35

Port Mirroring 35

Port Trunking 35

Storm Control 35

Static MAC Addresses 36

IP Address Filtering 36

IEEE 802.1D Bridge 36

Store-and-Forward Switching 36

Spanning Tree Algorithm 36

Virtual LANs 37

IEEE 802.1Q Tunneling (QinQ) 37

Traffic Prioritization 37

Quality of Service 37

IP Routing 38

Contents

– 8 –

Address Resolution Protocol 38

Multicast Filtering 38

Link Layer Discovery Protocol 39

System Defaults 39

Section II Web Configuration 43

2 Using the Web Interface 45

Connecting to the Web Interface 45

Navigating the Web Browser Interface 46

Dashboard 46

Configuration Options 48

Panel Display 49

Main Menu 50

3 Basic Management Tasks 67

Displaying System Information 68

Displaying Hardware/Software Versions 69

Configuring Support for Jumbo Frames 70

Displaying Bridge Extension Capabilities 71

Managing System Files 72

Copying Files via FTP/SFTP/TFTP or HTTP 72

Saving the Running Configuration to a Local File 75

Setting the Start-up File 76

Showing System Files 76

Automatic Operation Code Upgrade 77

Setting the System Clock 81

Setting the Time Manually 81

Setting the SNTP Polling Interval 82

Configuring NTP 83

Configuring Time Servers 84

Setting the Time Zone 88

Configuring Summer Time 89

Configuring the Console Port 91

Configuring Telnet Settings 93

Contents

– 9 –

Displaying CPU Utilization 94

Configuring CPU Guard 95

Displaying Memory Utilization 96

Resetting the System 97

4 Interface Configuration 101

Port Configuration 102

Configuring by Port List 102

Configuring by Port Range 104

Displaying Connection Status 105

Showing Port or Trunk Statistics 106

Displaying Statistical History 110

Displaying Transceiver Data 114

Configuring Transceiver Thresholds 115

Performing Cable Diagnostics 118

Trunk Configuration 119

Configuring a Static Trunk 121

Configuring a Dynamic Trunk 124

Configuring Load Balancing 129

Saving Power 131

Configuring Local Port Mirroring 133

Configuring Remote Port Mirroring 134

Sampling Traffic Flows 139

Configuring sFlow Receiver Settings 139

Configuring an sFlow Polling Instance 141

Traffic Segmentation 143

Enabling Traffic Segmentation 143

Configuring Uplink and Downlink Ports 144

5 VLAN Configuration 147

IEEE 802.1Q VLANs 147

Configuring VLAN Groups 149

Adding Static Members to VLANs 152

IEEE 802.1Q Tunneling 156

Enabling QinQ Tunneling on the Switch 160

Adding an Interface to a QinQ Tunnel 161

Contents

– 10 –

Protocol VLANs 162

Configuring Protocol VLAN Groups 163

Configuring MAC-based VLANs 164

6 Address Table Settings 167

Displaying the Dynamic Address Table 167

Clearing the Dynamic Address Table 168

Changing the Aging Time 169

Configuring MAC Address Learning 170

Setting Static Addresses 172

Issuing MAC Address Traps 174

7 Spanning Tree Algorithm 177

Overview 177

Configuring Loopback Detection 179

Configuring Global Settings for STA 181

Displaying Global Settings for STA 186

Configuring Interface Settings for STA 187

Displaying Interface Settings for STA 192

Configuring Multiple Spanning Trees 195

Configuring Interface Settings for MSTP 199

8 Congestion Control 201

Rate Limiting 201

Storm Control 202

9 Class of Service 205

Layer 2 Queue Settings 205

Setting the Default Priority for Interfaces 205

Selecting the Queue Mode 206

Layer 3/4 Priority Settings 209

Setting Priority Processing to DSCP or CoS 210

Mapping CoS Priorities to Per-hop Behavior 211

Mapping DSCP Priorities to Per-hop Behavior 212

10 Quality of Service 215

Overview 215

Contents

– 11 –

Configuring a Class Map 216

Creating QoS Policies 219

Attaching a Policy Map to a Port 222

11 VoIP Traffic Configuration 225

Overview 225

Configuring VoIP Traffic 226

Configuring Telephony OUI 227

Configuring VoIP Traffic Ports 228

12 Security Measures 231

AAA (Authentication, Authorization and Accounting) 232

Configuring Local/Remote Logon Authentication 233

Configuring Remote Logon Authentication Servers 234

Configuring AAA Accounting 239

Configuring AAA Authorization 245

Configuring User Accounts 248

Web Authentication 250

Configuring Global Settings for Web Authentication 251

Configuring Interface Settings for Web Authentication 252

Network Access (MAC Address Authentication) 253

Configuring Global Settings for Network Access 255

Configuring Network Access for Ports 256

Configuring a MAC Address Filter 258

Displaying Secure MAC Address Information 260

Configuring HTTPS 262

Configuring Global Settings for HTTPS 262

Replacing the Default Secure-site Certificate 263

Configuring the Secure Shell 265

Configuring the SSH Server 267

Generating the Host Key Pair 269

Importing User Public Keys 270

Access Control Lists 272

Showing TCAM Utilization 273

Setting the ACL Name and Type 275

Configuring a Standard IPv4 ACL 277

Contents

– 12 –

Configuring an Extended IPv4 ACL 278

Configuring a Standard IPv6 ACL 281

Configuring an Extended IPv6 ACL 282

Configuring a MAC ACL 284

Configuring an ARP ACL 286

Binding a Port to an Access Control List 288

Showing ACL Hardware Counters 289

Filtering IP Addresses for Management Access 292

Configuring Port Security 294

Configuring 802.1X Port Authentication 296

Configuring 802.1X Global Settings 298

Configuring Port Authenticator Settings for 802.1X 299

Displaying 802.1X Statistics 303

DoS Protection 304

DHCP Snooping 306

DHCP Snooping Global Configuration 309

DHCP Snooping VLAN Configuration 311

Configuring Ports for DHCP Snooping 312

Displaying DHCP Snooping Binding Information 313

IPv4 Source Guard 314

Configuring Ports for IPv4 Source Guard 314

Configuring Static Bindings for IPv4 Source Guard 316

Displaying Information for Dynamic IPv4 Source Guard Bindings 319

ARP Inspection 320

Configuring Global Settings for ARP Inspection 321

Configuring VLAN Settings for ARP Inspection 323

Configuring Interface Settings for ARP Inspection 325

Displaying ARP Inspection Statistics 326

Displaying the ARP Inspection Log 327

13 Basic Administration Protocols 329

Configuring Event Logging 330

System Log Configuration 330

Remote Log Configuration 332

Sending Simple Mail Transfer Protocol Alerts 333

Contents

– 13 –

Link Layer Discovery Protocol 335

Setting LLDP Timing Attributes 335

Configuring LLDP Interface Attributes 337

Configuring LLDP Interface Civic-Address 341

Displaying LLDP Local Device Information 343

Displaying LLDP Remote Device Information 347

Displaying Device Statistics 353

Power over Ethernet 355

Setting the Switch’s Overall PoE Power Budget 355

Setting the Port PoE Power Budget 357

Simple Network Management Protocol 360

Configuring Global Settings for SNMP 362

Setting the Local Engine ID 363

Specifying a Remote Engine ID 364

Setting SNMPv3 Views 365

Configuring SNMPv3 Groups 368

Setting Community Access Strings 373

Configuring Local SNMPv3 Users 374

Configuring Remote SNMPv3 Users 377

Specifying Trap Managers 380

Creating SNMP Notification Logs 384

Showing SNMP Statistics 386

Remote Monitoring 388

Configuring RMON Alarms 388

Configuring RMON Events 391

Configuring RMON History Samples 393

Configuring RMON Statistical Samples 396

Switch Clustering 398

Configuring General Settings for Clusters 399

Cluster Member Configuration 400

Managing Cluster Members 402

Setting a Time Range 403

LBD Configuration 406

Configuring Global Settings for LBD 406

Configuring Interface Settings for LBD 408

Contents

– 14 –

14 Multicast Filtering 411

Overview 411

Layer 2 IGMP (Snooping and Query for IPv4) 412

Configuring IGMP Snooping and Query Parameters 414

Specifying Static Interfaces for a Multicast Router 418

Assigning Interfaces to Multicast Services 420

Setting IGMP Snooping Status per Interface 422

Filtering IGMP Query Packets and Multicast Data 428

Displaying Multicast Groups Discovered by IGMP Snooping 429

Displaying IGMP Snooping Statistics 430

Filtering and Throttling IGMP Groups 434

Enabling IGMP Filtering and Throttling 435

Configuring IGMP Filter Profiles 435

Configuring IGMP Filtering and Throttling for Interfaces 438

MLD Snooping (Snooping and Query for IPv6) 439

Configuring MLD Snooping and Query Parameters 440

Setting Immediate Leave Status for MLD Snooping per Interface 442

Specifying Static Interfaces for an IPv6 Multicast Router 443

Assigning Interfaces to IPv6 Multicast Services 445

Showing MLD Snooping Groups and Source List 447

Displaying MLD Snooping Statistics 448

Filtering and Throttling MLD Groups 456

Enabling MLD Filtering and Throttling 457

Configuring MLD Filter Profiles 457

Configuring MLD Filtering and Throttling for Interfaces 460

Filtering MLD Query Packets on an Interface 462

15 IP Tools 463

Using the Ping Function 463

Using the Trace Route Function 464

Address Resolution Protocol 466

Basic ARP Configuration 467

Displaying Dynamic or Local ARP Entries 468

Displaying ARP Statistics 469

16 IP Configuration 471

Contents

– 15 –

Setting the Switch’s IP Address (IP Version 4) 471

Configuring IPv4 Interface Settings 471

Setting the Switch’s IP Address (IP Version 6) 475

Configuring the IPv6 Default Gateway 476

Configuring IPv6 Interface Settings 476

Configuring an IPv6 Address 481

Showing IPv6 Addresses 483

Showing the IPv6 Neighbor Cache 485

Showing IPv6 Statistics 486

Showing the MTU for Responding Destinations 492

17 General IP Routing 493

Overview 493

Initial Configuration 493

IP Routing and Switching 494

Routing Path Management 495

Routing Protocols 495

Configuring Static Routes 496

Displaying the Routing Table 497

18 Unicast Routing 499

Overview 499

Configuring the Routing Information Protocol 500

Configuring General Protocol Settings 501

Clearing Entries from the Routing Table 504

Specifying Network Interfaces 505

Specifying Passive Interfaces 507

Specifying Static Neighbors 508

Configuring Route Redistribution 509

Specifying an Administrative Distance 511

Configuring Network Interfaces for RIP 512

Displaying RIP Interface Settings 516

Displaying Peer Router Information 516

Resetting RIP Statistics 517

19 IP Services 519

Contents

– 16 –

Domain Name Service 519

Configuring General DNS Service Parameters 519

Configuring a List of Domain Names 520

Configuring a List of Name Servers 522

Configuring Static DNS Host to Address Entries 523

Displaying the DNS Cache 524

Multicast Domain Name Service 525

Dynamic Host Configuration Protocol 526

Specifying a DHCP Client Identifier 526

Configuring DHCP Relay Agent Mode 528

Configuring DHCP L2 Relay Service 529

Configuring DHCP L3 Relay Service 533

Enabling DHCP Dynamic Provision 534

Configuring DHCPv6 Relay Service 535

Section III Appendices 539

A Software Specifications 541

Software Features 541

Management Features 542

Standards 543

Management Information Bases 544

B Troubleshooting 547

Problems Accessing the Management Interface 547

Using System Logs 548

C License Information 549

The GNU General Public License 549

Glossary 553

– 17 –

Figures

Figure 1: Dashboard 47

Figure 2: Front Panel Indicators 49

Figure 3: System Information 68

Figure 4: General Switch Information 69

Figure 5: Configuring Support for Jumbo Frames 70

Figure 6: Displaying Bridge Extension Configuration 72

Figure 7: Copy Firmware 74

Figure 8: Saving the Running Configuration 75

Figure 9: Setting Start-Up Files 76

Figure 10: Displaying System Files 77

Figure 11: Configuring Automatic Code Upgrade 80

Figure 12: Manually Setting the System Clock 82

Figure 13: Setting the Polling Interval for SNTP 83

Figure 14: Configuring NTP 84

Figure 15: Specifying SNTP Time Servers 85

Figure 16: Adding an NTP Time Server 86

Figure 17: Showing the NTP Time Server List 86

Figure 18: Adding an NTP Authentication Key 87

Figure 19: Showing the NTP Authentication Key List 87

Figure 20: Setting the Time Zone 89

Figure 21: Configuring Summer Time 91

Figure 22: Console Port Settings 92

Figure 23: Telnet Connection Settings 94

Figure 24: Displaying CPU Utilization 95

Figure 25: Configuring CPU Guard 96

Figure 26: Displaying Memory Utilization 97

Figure 27: Restarting the Switch (Immediately) 99

Figure 28: Restarting the Switch (In) 99

Figure 29: Restarting the Switch (At) 100

Figures

– 18 –

Figure 30: Restarting the Switch (Regularly) 100

Figure 31: Configuring Connections by Port List 104

Figure 32: Configuring Connections by Port Range 105

Figure 33: Displaying Port Information 106

Figure 34: Showing Port Statistics (Table) 109

Figure 35: Showing Port Statistics (Chart) 110

Figure 36: Configuring a History Sample 112

Figure 37: Showing Entries for History Sampling 112

Figure 38: Showing Status of Statistical History Sample 113

Figure 39: Showing Current Statistics for a History Sample 113

Figure 40: Showing Ingress Statistics for a History Sample 114

Figure 41: Displaying Transceiver Data 115

Figure 42: Configuring Transceiver Thresholds 117

Figure 43: Performing Cable Tests 119

Figure 44: Configuring Static Trunks 121

Figure 45: Creating Static Trunks 122

Figure 46: Adding Static Trunks Members 122

Figure 47: Configuring Connection Parameters for a Static Trunk 123

Figure 48: Showing Information for Static Trunks 123

Figure 49: Configuring Dynamic Trunks 124

Figure 50: Configuring the LACP Aggregator Admin Key 127

Figure 51: Enabling LACP on a Port 128

Figure 52: Configuring LACP Parameters on a Port 128

Figure 53: Configuring Connection Settings for a Dynamic Trunk 129

Figure 54: Showing Connection Parameters for Dynamic Trunks 129

Figure 55: Configuring Load Balancing 131

Figure 56: Enabling Power Savings 132

Figure 57: Configuring Local Port Mirroring 133

Figure 58: Configuring Local Port Mirroring 134

Figure 59: Displaying Local Port Mirror Sessions 134

Figure 60: Configuring Remote Port Mirroring 135

Figure 61: Configuring Remote Port Mirroring (Source) 138

Figure 62: Configuring Remote Port Mirroring (Intermediate) 138

Figure 63: Configuring Remote Port Mirroring (Destination) 138

Figure 64: Configuring an sFlow Receiver 141

Figures

– 19 –

Figure 65: Showing sFlow Receivers 141

Figure 66: Configuring an sFlow Instance 142

Figure 67: Showing sFlow Instances 143

Figure 68: Enabling Traffic Segmentation 144

Figure 69: Configuring Members for Traffic Segmentation 146

Figure 70: Showing Traffic Segmentation Members 146

Figure 71: VLAN Compliant and VLAN Non-compliant Devices 148

Figure 72: Creating Static VLANs 151

Figure 73: Modifying Settings for Static VLANs 151

Figure 74: Showing Static VLANs 152

Figure 75: Configuring Static Members by VLAN Index 154

Figure 76: Configuring Static VLAN Members by Interface 155

Figure 77: Configuring Static VLAN Members by Interface Range 156

Figure 78: QinQ Operational Concept 157

Figure 79: Enabling QinQ Tunneling 161

Figure 80: Adding an Interface to a QinQ Tunnel 162

Figure 81: Configuring Protocol VLANs 164

Figure 82: Displaying Protocol VLANs 164

Figure 83: Configuring MAC-Based VLANs 166

Figure 84: Showing MAC-Based VLANs 166

Figure 85: Displaying the Dynamic MAC Address Table 168

Figure 86: Clearing Entries in the Dynamic MAC Address Table 169

Figure 87: Setting the Address Aging Time 170

Figure 88: Configuring MAC Address Learning 171

Figure 89: Configuring Static MAC Addresses 173

Figure 90: Displaying Static MAC Addresses 173

Figure 91: Issuing MAC Address Traps (Global Configuration) 174

Figure 92: Issuing MAC Address Traps (Interface Configuration) 175

Figure 93: STP Root Ports and Designated Ports 178

Figure 94: MSTP Region, Internal Spanning Tree, Multiple Spanning Tree 178

Figure 95: Spanning Tree – Common Internal, Common, Internal 179

Figure 96: Configuring Port Loopback Detection 181

Figure 97: Configuring Global Settings for STA (STP) 185

Figure 98: Configuring Global Settings for STA (RSTP) 185

Figure 99: Configuring Global Settings for STA (MSTP) 186

Figures

– 20 –

Figure 100: Displaying Global Settings for STA 187

Figure 101: Determining the Root Port 189

Figure 102: Configuring Interface Settings for STA 192

Figure 103: STA Port Roles 193

Figure 104: Displaying Interface Settings for STA 194

Figure 105: Creating an MST Instance 196

Figure 106: Displaying MST Instances 196

Figure 107: Modifying the Priority for an MST Instance 197

Figure 108: Displaying Global Settings for an MST Instance 197

Figure 109: Adding a VLAN to an MST Instance 198

Figure 110: Displaying Members of an MST Instance 198

Figure 111: Configuring MSTP Interface Settings 200

Figure 112: Displaying MSTP Interface Settings 200

Figure 113: Configuring Rate Limits 202

Figure 114: Configuring Storm Control 204

Figure 115: Setting the Default Port Priority 206

Figure 116: Setting the Queue Mode (Strict) 208

Figure 117: Setting the Queue Mode (WRR) 208

Figure 118: Setting the Queue Mode (Strict and WRR) 209

Figure 119: Setting the Trust Mode 211

Figure 120: Configuring CoS to Queue Mapping 212

Figure 121: Configuring DSCP to Queue Mapping 214

Figure 122: Configuring a Class Map 217

Figure 123: Showing Class Maps 218

Figure 124: Adding Rules to a Class Map 218

Figure 125: Showing the Rules for a Class Map 219

Figure 126: Configuring a Policy Map 221

Figure 127: Showing Policy Maps 221

Figure 128: Adding Rules to a Policy Map 222

Figure 129: Showing the Rules for a Policy Map 222

Figure 130: Attaching a Policy Map to a Port 223

Figure 131: Configuring a Voice VLAN 227

Figure 132: Configuring an OUI Telephony List 228

Figure 133: Showing an OUI Telephony List 228

Figure 134: Configuring Port Settings for a Voice VLAN 230

Page is loading ...

Edge-Core ECS2100-28PP User manual

This manual is also suitable for

Edge-Core ECS2100-28PP User manual

Related papers

Other documents