i3 International Ax73RM Quick start guide
- Category
- Security cameras
- Type
- Quick start guide
This manual is also suitable for
The i3 International Ax73RM-series 5MP Infrared Outdoor IP Dome Camera with Motorized Lens is a high-definition surveillance camera suitable for both indoor and outdoor use. With its motorized lens, you can remotely adjust the camera's field of view and focus, even in low-light conditions with its infrared capabilities.
The i3 International Ax73RM-series 5MP Infrared Outdoor IP Dome Camera with Motorized Lens is a high-definition surveillance camera suitable for both indoor and outdoor use. With its motorized lens, you can remotely adjust the camera's field of view and focus, even in low-light conditions with its infrared capabilities.
CAMERA PARTS AND DEFINITIONS
Quick Start Guide
5MP Infrared Outdoor IP Dome Camera w/ Motorized Lens Ax73RM-series
SAFETY
When installing your Ax73RM camera be sure to avoid:
• excessive heat, such as direct sunlight or heating appliances
• contaminants such as dust and smoke
• strong magnetic fields
• sources of powerful electromagnetic radiation such as radios or TV transmitters
• moisture and humidity
• areas with mechanical vibrations
• fluorescent lamps or objects that reflect light
• unstable light sources as this may cause flickering
• temperatures below -40° Celsius (-40° Fahrenheit) and above 50° Celsius (122°
Fahrenheit).
POWER SUPPLY
Ensure the supplied voltage meets the power consumption requirements of this camera
before powering the camera on. Incorrect voltage may cause irreparable damage to the
video camera and will effectively void the camera warranty.
CLEANING
• For maximum optical clarity, the camera dome or lens must remain clean. Use a soft,
dry cloth to remove finger prints or dust from the dome cover.
• Use a blower to remove dust from the lens.
• Clean the body with a soft, dry cloth. If it is very dirty, use a cloth dampened with a
small quantity of neutral detergent, then wipe dry.
• Do not use volatile solvents such as alcohol, benzene, or thinners, as they may dam-
age the surface finishes.
SERVICING
To avoid electrical shock and to preserve the product warranty, DO NOT disasemble the
camera. Refer servicing to qualified personnel only.
PACKAGE CONTENTS
Ensure that the items received match those listed on the order form and the packing slip.
In addition to this manual and a fully assembled camera, the dome camera packing box
includes:
1. Surface Mount template x1
2. Rubber gasket x1. Use in all outdoor installations.
3. Flush Mount template x1
4. Round Head Screw (Tapping Type) with O-ring x4
5. Plastic Anchor x4
6. Long Screws for Flush Mount w/Back Box installations x3
7. Standard RJ45 Connector x2
8. Security torx bit x1
i3-TRNG-CAMS-Ax73RM-QuickGuide.indd
Rev. 160829
ACCESSORIES (not to scale)
1 3
4
8
5 6 7
2
Lens Direction
GUIDE PATTERN
GUIDE PATTERN
CAMERA OUTLINE
CUT LINE
O-ring
Please Note: Scan the QR code at the bottom of this document or visit www.i3interna-
tional.com to view and download the full User Manual for this camera. Also available for
download is the AnnexxusConfigurationTool or ACT program used to locate and config-
ure your cameras with your SRX-Pro software. This program is already installed in SRX-Pro
v3.3.3.69 and higher. Please contact our Technical Support team if you have any questions
or concerns regarding camera installation or you require software services or support.
Technical support can be reached by email at:
[email protected] or by phone toll free 1.877.877.7241.
I/O CONNECTORS
Ax73RM-series 5MP IP Dome Camera
QUICK START GUIDE
1. Camera’s back box
2. Screws attaching camera module to the back box
(x3, silver)
3. Camera module / second housing
4. Tilt bracket with locking screws
5. Inner liner / Shroud
6. IR board
7. Dome bubble housing / Dome cover
8. Screws securing the dome bubble housing to camera module (x3, silver)
9. Lexan bubble
10. 3/4” Top conduit hole. During installation, sealant must be used to maintain the IP66
status.
11. 3/4” Side conduit hole. During installation, sealant must be used to maintain the
IP66 status.
DISASSEMBLING THE CAMERA
CONNECT CAMERA TO i3 SRX-PRO SERVER
Camera’s default IP: 192.0.0.16. Default Login / PW: i3admin / i3admin
Connection Type 1:
i3 SRX-Pro Server
Crossover direct connection
LAN
i3 SRX-Pro Server
Via Gigabit Switch
Connection Type 2:
Audio In
Audio Out Alarm Out Alarm In
Locking
arms (x2)
1. Use the provided security Torx
key to loosen three screws se-
curing the dome bubble housing
to camera module (#8). Do not
completely remove the screws
from the dome bubble
2. Next, loosen three silver screws attach-
ing camera to the back box.
3. Remove camera’s back box and set
aside.
Once the camera dome bubble has been removed, Ax73RM input/output connectors will
be revealed on the camera’s module, including the microSD slot, Factory Reset and Factory
Default, analog RCA video jack, RJ-45 Ethernet/PoE connector, Audio and Alarm connectors
as well as a AC24V port.
1. Audio and Alarm I/O connectors.
2. AC 24V Port. Connect AC 24V power supply.
3. RJ-45 Ethernet Connector / PoE. Connect RJ-45 network cable for ethernet/internet
connectivity. PoE (Power over Ethernet) is supported.
NOTE on Power:
Do not apply power until the camera is properly and securely mounted.
4. Orange LED. Flashing orange LED indicates data transmission b/w camera and the
Internet.
5. Green LED. Solid green LED indicates a current live connection.
1. Close SRX-Pro Server software by pressing Alt+Shift+Ctrl+F4.
2. Write down the IP address on the onboard NIC (LAN) (or on NIC1 if your SRX-Pro
Server has two onboard NIC cards).
3. Connect your camera to i3 SRX-Pro Server (see diagram above).
4. Turn on your Annexxus camera.
5. It may be necessary to download and install AnnexxusConfigTool (ACT) from our
website (www.i3international.com). Follow the ACT installation instructions until
the application has been successfully installed on your SRX-Pro Server. For SRX-
Pro v3.3.3.69 and above ACT is already installed.
6. Either double-click i3 Annexxus Configuration Tool icon on the desktop to launch
the ACT application or click the “ACT Config Tool” button on the IP Camera Tab
in SRX-Pro.
7. ANNEXXUS Configuration Tool window will display a list of active network
cameras.
8. Select the desired Annexxus camera in the list (left-click).
9. In the Device(s) Communication area, enter the new IP Range (address) and
Subnet Mask of the camera. The new camera IP address must match the IP
range of your SRX-Pro LAN or NIC1 card (see Step 2).
E.g. If your SRX-Pro Server’s IP address is 192.138.10.122, change your
Annexxus camera’s IP address to 192.138.10.XXX.
Remember: Annexxus Cameras cannot share an IP address, each camera
requires its own unique IP address.
10. Make sure the Default Account checkbox is checked off.
11. Click Update. Wait a few moments for a successful confirmation message.
12. Repeat Steps 9-12 for all detected Annexxus cameras in the ACT application
OR Select multiple cameras (Ctrl + left click) and enter IP range to assign IP
addresses sequentially to the selected cameras.
13. Once the IP address of the Annexxus camera(s) has been changed, make sure
you can connect to the camera(s) through Internet Explorer:
a. Launch Internet Explorer and enter the IP Address you have just assigned to
your Annexxus camera. The password window should be displayed.
b. Enter the default camera User Name: i3admin and default Password:
i3admin
c. Annexxus camera interface will be displayed in the Internet Explorer
window. You should be able to see the camera image on the screen.
If you do not see the camera image on the screen, call i3 International tech
support for troubleshooting tips: 1.877.877.7241
14. Make sure that the latest version of GiPi updater is installed on your SRX-Pro
Server. You can download the updates from ftp://files.123ip.com/drivers/gipi.
Please contact i3 Technical Support team for access information.
15. Once the latest GiPi updater has been installed, restart i3 SRX-Pro Server.
16. Log In and go to the Setup -> IP Camera tab.
17. Click the Search button to display connected Annexxus cameras.
18. Select the detected camera in the list and click Select.
19. In the
Select IP Camera
window, enter the default camera User Name: i3admin
and default Password: i3admin, then click Add.
20. The selected camera will be added to the IP Camera list.
21. Assign the IP camera to the SRX-Pro video channel in the Ch. In. column.
22. Select i3 GiPi from the PTZ column to enable motorized lens’ autofocus feature.
23. Your Annexxus camera is now connected to SRX-Pro Server and is ready to
record. You may change resolution and frame rate for the Annexxus camera in
the IP Camera tab menu or you may choose to configure the camera’s advanced
settings.
QR Code to Complete
User Manual
CANADA 780 Birchmount Road,
Unit 16, Toronto,
ON, M1K 5H4
U.S.A 4450 Witmer Industrial Estates
Unit 4 Niagara Falls,
NY 14305
www.i3international.com
1.866.840.0004
-
1
-
2
i3 International Ax73RM Quick start guide
- Category
- Security cameras
- Type
- Quick start guide
- This manual is also suitable for
The i3 International Ax73RM-series 5MP Infrared Outdoor IP Dome Camera with Motorized Lens is a high-definition surveillance camera suitable for both indoor and outdoor use. With its motorized lens, you can remotely adjust the camera's field of view and focus, even in low-light conditions with its infrared capabilities.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
i3 International Ax46R-66R Quick start guide
-
-
-
-
-
-
-
-
-
