Cascadia T0329 Installation guide

Cascadia
Brand
Cascadia
Model
T0329
Category
Floodlights
Type
Installation guide

This manual is also suitable for

Cascadia T0329 is a versatile and durable LED flood light designed for both wall and eave mounting. It features adjustable light heads that allow you to direct the light coverage area as desired. With a maximum wattage of 28W, it provides ample illumination for various outdoor applications, including security lighting, landscape lighting, and general area lighting. The fixture requires a 120 VAC, 60 Hz power source and can be controlled using a standard on/off wall switch. Its IP65 rating ensures resistance to dust and water, making it suitable for outdoor use in all weather conditions.

Cascadia T0329 is a versatile and durable LED flood light designed for both wall and eave mounting. It features adjustable light heads that allow you to direct the light coverage area as desired. With a maximum wattage of 28W, it provides ample illumination for various outdoor applications, including security lighting, landscape lighting, and general area lighting. The fixture requires a 120 VAC, 60 Hz power source and can be controlled using a standard on/off wall switch. Its IP65 rating ensures resistance to dust and water, making it suitable for outdoor use in all weather conditions.

Page 1 / 3
170413
Important to Know:
1. If you are not familiar with state and local electrical codes, it is recommended that you consult with a qualified
electrician.
2. This fixture requires a 120 VAC, 60 Hz power source.
3. For general safety be sure the power is switched "off" before adjustment.
4. Switch control LED flood light.
Note:Only general ON/OFF wall switch applies for this fixture, the dimmable wall switch shouldn’t be
required.
Maximum Wattage: 28 W
Working Temperature Range: -4ºF ~ 113ºF
ASSEMBLY AND INSTALLATION
INSTRUCTIONS
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
T0329 / T0330
WARNING:
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
Note: Fixture can be wall mounted or eave mounted.
Light fixture and light head should be mounted as shown above when installed (depending upon type of installation).
Hardware Package (included):
Mounting Screw X2
#8/32X1/2 in
Fixture Mounting Screw
Mounting Strap
Wire Connector X3
Mounting Screw X2
#6/32 X1/2 in
Mounting Screw X2
#10/24 X1/4 in
Decorative cover Gasket
Mounting Strap
Outlet Box
Mounting Screw
Back Plate
Fixture Mounting Screw
Decorative Cover
Gasket
Wire
Connector
FRONT
Wall Mounted
Eave Mounted
Page 2 / 3
170413
Installation Steps
1. Install the mounting strap to the outlet box with the stamped word “FRONT” facing away from the outlet box, using
two mounting screws that best fit the outlet box. (Choose one matching pair of suitable mounting screws from the 3
pairs provided)
2. Thread the fixture wires through gasket, and then attach the gasket into back plate of the light fixture.
3. Pull out the source wires from the outlet box. Make wire connections using
wire connectors as follows:
---Connect the black wire from the fixture to the “hot” wire from the power source. (usually black)
---Connect the white wire from the fixture to the neutral wire from the power source. (usually white)
---Connect the grounding wire from the fixture to the grounding wire from the power source. (usually green / yellow
insulation)
Carefully tuck the wires back into the outlet box.
4. Attach the back plate of the light fixture to the mounting strap, and then secure it with the fixture mounting screw.
Push the decorative cover firmly into the fixture mounting screw hole on the light fixture.
5. With silicone caulking compound, caulk completely around where the mounting bracket meets the wall surface.
CAUTION: Be sure to caulk completely where the mounting bracket meets the wall surface to prevent water
from seeping into the outlet box.
Turn off the power at fuse or circuit box.
Turn on the power at fuse or circuit box.
Adjusting the Light Head:
1. Gently grasp the light head and tilt them up or down, left or right to adjust the light coverage area as you desired.
(See Fig. 1)
1
Axis
Joint Arm-1
Joint Arm-2
Joint Arm-2
Axis
Joint Arm-2
Light Head
Page 3 / 3
170413
Fixture Mounting Screw
Decorative cover Gasket
Troubleshooting
---The light does not come on at all:
1. Make sure the wall switch and circuit breaker are on.
2. Make sure the wiring is correct.
---The light flashes on and off:
1. Use a standard on/off wall switch to control the light fixture, instead of a dimmer and timer.
Mounting Screw X2
#8/32X1/2 in
Mounting Strap
Wire Connector X3
Mounting Screw X2
#6/32 X1/2 in
Mounting Screw X2
#10/24 X1/4 in
A: 5-1/2"
B: 4-3/4"
C: 7"
Assembly Kit
5704MM (1 SET) FOR T0329
5705MM (1 SET) FOR T0330
The following parts are available for re-order if damaged or missing.
5-YEAR LIMITED WARRANTY:
All products are warranted to be free of defects in material and workmanship for five (5) years from date of purchase.
This warranty is limited to the correction of any such defect, or the replacement of any such defective item(s), provided
that: (a) we are properly notified and consent to return of the item(s) in question:(b) the item(s) is / are returned with
proof of purchase date; and (c) it is found upon inspection by us that the item(s) is / are defective as noted above. This
warranty does not cover labor costs, consequential damages, nor does it apply to any item(s) that have been
improperly installed, overloaded, altered, or otherwise abused by the customer, its agent(s) or employee(s). Finishes
are specially excluded from the terms of this warranty since they are subject to environmental maintenance deemed
beyond our control. Other than the described obligation, we assume no further liability with respect to the sale or use of
our products. We make no warranty, express or implied, and disclaim any warranty of merchantability or fitness for a
particular purpose.
A
C
B
  • Page 1 1
  • Page 2 2
  • Page 3 3

Cascadia T0329 Installation guide

Cascadia
Brand
Cascadia
Model
T0329
Category
Floodlights
Type
Installation guide
This manual is also suitable for

Cascadia T0329 is a versatile and durable LED flood light designed for both wall and eave mounting. It features adjustable light heads that allow you to direct the light coverage area as desired. With a maximum wattage of 28W, it provides ample illumination for various outdoor applications, including security lighting, landscape lighting, and general area lighting. The fixture requires a 120 VAC, 60 Hz power source and can be controlled using a standard on/off wall switch. Its IP65 rating ensures resistance to dust and water, making it suitable for outdoor use in all weather conditions.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents