HySecurity SlideDriver Snow Brushes and Snow Scrapers Installation guide

Brand: HySecurity

Model: SlideDriver Snow Brushes and Snow Scrapers

Category: Wall & ceiling mounts accessories

Type: Installation guide

SlideDriver with Snow Brush and Scraper Kits installed

Installation Instructions

MX001223, MX001224, MX001229, MX001782

Snow brushes

(rail not shown)

Snow scraper

Section 1: SlideDriver™— Optional Snow Kits

The snow brush and snow scraper kits help keep ice and snow buildup

at a minimum along the drive rail of the SlideDriver gate operator.

These instructions explain how to:

 Install snow brushes

 Install snow scrapers

 Prevent ice buildup on outside limit switch arms

NOTE: The snow brush and snow scraper kits can be ordered togeth-

er or separately. These instructions explain the installation process.

Section 2: Installing the Snow Brushes

1. Loosen the two Phillips-head screws that secure the cover to the

SlideDriver chassis.

2. Remove the cover and set it on a level work surface.

3. Turn off the power to the operator using the power toggle switch,

located on the Control Box.

4. Slide the snow brushes into place and secure them using the fas-

teners provided. The aluminum flange should be inside the opera-

tor. See photo and illustrations for proper mounting location.

5. Insert the mounting bolts through the chassis from the outside and

attach the supplied washers and Nylock® nuts (next page). Secure

the fasteners using a crescent wrench and Phillips-head screwdriv-

er. Refer to the illustrations.

6. Turn the power on.

7. Test the gate operator and make sure it functions properly.

8. Carefully, replace the cover and secure it to the chassis. Loosen two screws

to remove cover.

Power

toggle switch

Control Box

Remove

cover and

set it aside.

4 Place the aluminum ﬂange on

the inside of the chassis and

slide snowbrushes into place.

CORRECT installaƟon of snowbrushes

Install the snow brushes so the aluminum ﬂange is inside the chassis.

Use the supplied washers and nuts to secure the fasteners.

Section 3: Installing the Snow Scrapers

To mount the plastic snow scrapers, refer to the photograph on page 1.

1. Follow steps 1 through 3 on page 1, Install the Snow Brushes.

2. Take note of the orientation of the right and left snow scrapers. Slide

the brackets into place and adjust them so the scraper rests about ⅛

-inch above the drive rail. Secure the bracket using the fasteners

provided.

3. Follow steps 6 through 8 above.

Section 4: Preventing Ice Buildup

On the SlideDriver 50VF2 and 50VF3 operators, limit switch arms are

mounted on the outside of the SlideDriver chassis. On occasion, the

arms can stick due to ice buildup and cause the drive rail to jam. If this

type of incident occurs often, cut approximately 4-inches (10cm) off the

ends of the lower brush as shown in the illustration. Pack the limit

switches with silicone grease to help prevent ice buildup.

Section 5: Maintenance

For Maintenance or Troubleshooting issues, refer to the SlideDriver

Installation, Operation, and Maintenance Manual (D0119) that accom-

panies the operator. The manual is also downloadable from the HySecu-

rity website.

CAUTION

The front cover is heavy. As you replace it, be aware that you need

to position your hands in such a way as to avoid pinching your fin-

gers between the edge of the chassis and the cover.

VF2/VF3—Prevent ice buildup

Cut about 4‐inches (10cm) oﬀ the lower brushes

to prevent ice build‐up on the outside limit

switches. Pack the switch arms with silicone

grease.

CAUTION:

Be aware of the

pinch points

when replacing

the front cover.

Insert the bolts

from the outside

and secure each

one inside the

chassis with the

supplied washer

and nut.

HySecurity SlideDriver Snow Brushes and Snow Scrapers Installation guide

Brand: HySecurity

Model: SlideDriver Snow Brushes and Snow Scrapers

Category: Wall & ceiling mounts accessories

Type: Installation guide

Download PDF

report

HySecurity SlideDriver Snow Brushes and Snow Scrapers Installation guide

HySecurity SlideDriver Snow Brushes and Snow Scrapers Installation guide

Related papers

Other documents