Sewell SW-32988 BlastIR Wireless Pro IR Repeater User manual

Brand
Sewell
Model
SW-32988 BlastIR Wireless Pro IR Repeater
Type
User manual

Sewell SW-32988 BlastIR Wireless Pro IR Repeater gives you the ability to control IR devices that are hidden from view or in hard-to-reach locations. The IR emitters transmit from the adhesive side of the head and should be adhered directly over the location where your device receives its IR signal. With a range of up to 100 feet, you can easily control your devices from anywhere in the room. The BlastIR Wireless Pro IR Repeater is also easy to set up and use. Simply connect the emitter to the IR output of your source device, and the receiver to the IR input of your target device.

Sewell SW-32988 BlastIR Wireless Pro IR Repeater gives you the ability to control IR devices that are hidden from view or in hard-to-reach locations. The IR emitters transmit from the adhesive side of the head and should be adhered directly over the location where your device receives its IR signal. With a range of up to 100 feet, you can easily control your devices from anywhere in the room. The BlastIR Wireless Pro IR Repeater is also easy to set up and use. Simply connect the emitter to the IR output of your source device, and the receiver to the IR input of your target device.

BlastIR Wireless IR Receiver
BlastIR Wireless IR Emitter
Dual IR Emitter Cable
IR Receiver Cable
(2) Airstick™ Microsuction Tape
(2) 3m Adhesive
(2) 5V .5A Power Supply
(2) USB to DC Cable
(2) Rubber Magnet Feet
10
Optional IR Emitter
Cable Port
Optional IR Receiver
Cable Port
Built-in IR Emitter
Status LED
Built-in IR Receiver
The IR Emitters transmit from
from the adhesive side of the
head and should be adhered
directly over the location
where your device receives
its IR signal. (Location Varies)
Troubleshooting
- The BlastIR Wireless Pro transmission range can be reduced
by walls or other objects between the receiver and emitter as
well as by other wireless signals in the same area. If you are having
trouble with the emitter receiving the signal we recommend testing
it with the receiver and emitter in the same room in order to verify
that nothing is interfering with the signal.
- If the emitter or receiver seems to be cutting in and out, then the
power connector may not be properly seated. We recommend
reseating in the power connector. Keeping the modules in a place
where there is minimal vibration or other movement will help
prevent the power connectors from coming loose.
- Make sure that they receiver and emitter are set to the same
desired channel before use. If they are on a different channel, then
the emitter will not recognize the signal from the receiver.
BlastIR Wireless IR Receiver
BlastIR Wireless IR Emitter
Dual IR Emitter Cable
IR Receiver Cable
(2) Airstick™ Microsuction Tape
(2) 3m Adhesive
(2) 5V .5A Power Supply
(2) USB to DC Cable
(2) Rubber Magnet Feet
The IR Emitters transmit from
from the adhesive side of the
head and should be adhered
directly over the location
where your device receives
its IR signal. (Location Varies)
10
Optional IR Emitter
Cable Port
Optional IR Receiver
Cable Port
Built-in IR Emitter
Status LED
Built-in IR Receiver
Troubleshooting
- The BlastIR Wireless Pro transmission range can be reduced
by walls or other objects between the receiver and emitter as
well as by other wireless signals in the same area. If you are having
trouble with the emitter receiving the signal we recommend testing
it with the receiver and emitter in the same room in order to verify
that nothing is interfering with the signal.
- If the emitter or receiver seems to be cutting in and out, then the
power connector may not be properly seated. We recommend
reseating in the power connector. Keeping the modules in a place
where there is minimal vibration or other movement will help
prevent the power connectors from coming loose.
- Make sure that they receiver and emitter are set to the same
desired channel before use. If they are on a different channel, then
the emitter will not recognize the signal from the receiver.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

Sewell SW-32988 BlastIR Wireless Pro IR Repeater User manual

Brand
Sewell
Model
SW-32988 BlastIR Wireless Pro IR Repeater
Type
User manual

Sewell SW-32988 BlastIR Wireless Pro IR Repeater gives you the ability to control IR devices that are hidden from view or in hard-to-reach locations. The IR emitters transmit from the adhesive side of the head and should be adhered directly over the location where your device receives its IR signal. With a range of up to 100 feet, you can easily control your devices from anywhere in the room. The BlastIR Wireless Pro IR Repeater is also easy to set up and use. Simply connect the emitter to the IR output of your source device, and the receiver to the IR input of your target device.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents