Cisco 350 & 550 Series Managed Switches Administration Guide
First Published: 2020-05-07
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
©2020 Cisco Systems, Inc. All rights reserved.
CHAPTER 1
Get To Know Your Switch
This chapter contains the following sections:
Introduction, on page 1
Rack Mounting Switch, on page 2
Power over Ethernet Considerations, on page 3
Front Panel, on page 6
Configuring Switches, on page 8
Out-Of-Band Port, on page 11
Stacking the Switches, on page 11
Product Models, on page 11
Navigation, on page 14
Introduction
Thank you for puchasing the Cisco Business Series Switch, which offers Cisco’s most cost-effective stackable
managed switches. Simple to deploy and manage, the Cisco Business Series switches provide 24 or 48 ports
of 1G connectivity with 10G uplinks, or 12 to 48 ports of 10G connectivity, providing a solid foundation for
business applications. The advanced features make these switches the ideal choice for aggregation, access,
or server room switches, for any business looking for a reliable solution in an affordable price range.
Before You Begin
Before you begin installing your device, ensure that the following items are available:
RJ-45 Ethernet cables for connecting network devices. A category 6a and higher cable is required for
10G ports; a category 5e and higher cable is required for all other ports.
Console cable for using the console port to manage your switch.
Tools for installing the hardware.
The rack-mount kit packed with the switch contains four rubber feet for desktop placement, and
two brackets and twelve screws for rackmounting.
If the supplied screws are lost, use replacement screws in the following size:
Diameter of the screw head: 6.9 mm
Length of face of screw head to base of screw: 5.9 mm
Cisco 350 & 550 Series Managed Switches Administration Guide
1
Shaft diameter: 3.94 mm
Computer running on of the following browsers: Microsoft Edge or Firefox (version 74 or 73 or higher),
or Chrome (version 80 or 79 or higher), or Safari over MAC (version 12.1 and higher) for using the
web-based interface or the console port to manage your switch.
Suitable for installation in information Technology Rooms in accordance with Article 645 of the national
Electric Code and NFPA 75.
Warning
Rack Mounting Switch
You can mount the switches on any standard size, 19-inch (about 48 cm) wide rack. The switch requires 1
rack unit (RU) of space, which is 1.75 inches (44.45 mm) high.
For stability, load the rack from the bottom to the top, with the heaviest devices on the bottom. A top-heavy
rack is likely to be unstable and might tip over.
Caution
To install the switch into a 19-inch standard chassis:
Step 1 Place one of the supplied brackets on the side of the switch so that the four holes of the brackets align to the screw holes,
and then use the four supplied screws to secure it.
Step 2 Repeat the previous step to attach the other bracket to the opposite side of the switch.
Step 3 After the brackets are securely attached, the switch is now ready to be installed into a standard 19-inch rack.
Cisco 350 & 550 Series Managed Switches Administration Guide
2
Get To Know Your Switch
Rack Mounting Switch
Power over Ethernet Considerations
Some switches support PoE while others do not. The switch models that support PoE have a P in their model
number, such as: Sxxx-xxP-xx. If your switch is one of the Power over Ethernet (PoE) models, consider the
following power requirement.
The switch is to be connected only to PoE networks without routing to the outside plant.
Danger
Table 1: Switches with Power Over Ethernet
PoE PSE
AF/AT/60W
PoE PD
AF/AT/60W
PoE PSE Chipset
Type
PoE PD Chipset
Type
DescriptionSKU Name
ATAF/AT/60W1*69208M
(0x4B42)
2x PD70210 +
2x PD70222 +
1?x LX7309
SF352-08P
8-Port 10/100
PoE Managed
Switch
SF352-08P
ATAF/AT/60W1*69208M
(0x4B42)
2x PD70210 +
2x PD70222 +
1?x LX7309
SF352-08MP
8-Port 10/100
PoE Managed
Switch
SF352-08MP
AF/AT/60WN/A3*69208M
(0x4B42) +
1*69204
N/ASF350-24P
24-Port 10/100
PoE Managed
Switch
SF350-24P
AF/AT/60WN/A3*69208M
(0x4B42) +
1*69204
N/ASF350-24MP
24-Port 10/100
PoE Managed
Switch
SF350-24MP
AF/AT/60WN/A7* PD69208
(0x4AC2) /
7*69208M
(0x4B42) (as of
2.2.7)
N/ASF350-48P
48-Port 10/100
PoE Managed
Switch
SF350-48P
AF/AT/60WN/A7*69208M
(0x4B42)
N/ASF350-48P
48-Port 10/100
PoE Managed
Switch
SF350-48P
AF/AT/60WN/A7* PD69208
(0x4AC2) /
7*69208M
(0x4B42)
N/ASF350-48MP
48-Port 10/100
PoE Managed
Switch
SF350-48MP
Cisco 350 & 550 Series Managed Switches Administration Guide
3
Get To Know Your Switch
Power over Ethernet Considerations
PoE PSE
AF/AT/60W
PoE PD
AF/AT/60W
PoE PSE Chipset
Type
PoE PD Chipset
Type
DescriptionSKU Name
ATAF/AT/60W1* PD69208
(0x4AC2) /
1*69208M
(0x4B42)
2x PD70210 +
2x PD70222 +
1?x LX7309
SG352-10P-E
10-Port Gigabit
PoE Managed
Switch
SG352-10P-E
ATAF/AT/60W1* PD69208
(0x4AC2) /
1*69208M
(0x4B42)
2x PD70210 +
2x PD70222 +
1?x LX7309
SG352-10P
10-Port Gigabit
PoE Managed
Switch
SG352-10P
ATAF/AT/60W1* PD69208
(0x4AC2) /
1*69208M
(0x4B42)
2x PD70210 +
2x PD70222 +
1?x LX7309
SG352-10MP-E
10-Port Gigabit
PoE Managed
Switch
SG352-10MP-E
AF/AT/60WN/A3x PD69208+
1*PD69204
(0x4AC2) /
3*69208M
(0x4B42) +
1*69204
N/ASG352-28P
28-Port Gigabit
PoE Managed
Switch
SG352-28P
AF/AT/60WN/A3x PD69208+
1*PD69204
(0x4AC2) /
3*69208M
(0x4B42) +
1*69204
N/ASG352-28MP
28-Port Gigabit
PoE Managed
Switch
SG352-28MP
AF/AT/60WN/A7*69208M
(0x4B42)
N/ASG352-52P
52-Port Gigabit
PoE Managed
Switch
SG352-52P
AF/AT/60WN/A7*69208M
(0x4B42)
N/ASG352-52MP
52-port Gigabit
PoE Managed
Switch
SG352-52MP
af/at/60wN/A3x PD69208+
1*PD69204
(0x4AC2) /
3*69208M
(0x4B42) +
1*69204
N/ASG352X-24P
24-Port Gigabit
PoE Stackable
Managed Switch
SG352X-24P
Cisco 350 & 550 Series Managed Switches Administration Guide
4
Get To Know Your Switch
Power over Ethernet Considerations
PoE PSE
AF/AT/60W
PoE PD
AF/AT/60W
PoE PSE Chipset
Type
PoE PD Chipset
Type
DescriptionSKU Name
af/at/60wN/A3x PD69208+
1*PD69204
(0x4AC2) /
3*69208M
(0x4B42) +
1*69204
N/ASG352X-24MP
24-Port Gigabit
PoE Stackable
Managed Switch
SG352X-24MP
af/at/60wN/A7* PD69208
(0x4AC2) /
7*69208M
(0x4B42)
N/ASG352X-48P
48-Port Gigabit
PoE Stackable
Managed Switch
SG352X-48P
af/at/60wN/A7* PD69208
(0x4AC2) /
7*69208M
(0x4B42)
N/ASG352X-48MP
48-Port Gigabit
PoE Stackable
Managed Switch
SG352X-48MP
af/at/60wN/A4* PD69208
(0x4AC2) /
4*69208M
(0x4B42)
N/ASF550X-24P
24-Port 10/100
PoE Stackable
Managed Switch
SF550X-24P
af/at/60wN/A4* PD69208
(0x4AC2) /
4*69208M
(0x4B42)
N/ASF550X-24MP
24-Port 10/100
PoE Stackable
Managed Switch
SF550X-24MP
af/at/60wN/A7* PD69208
(0x4AC2) /
7*69208M
(0x4B42)
N/ASF550X-48P
48-Port 10/100
PoE Stackable
Managed Switch
SF550X-48P
af/at/60wN/A7* PD69208
(0x4AC2) /
7*69208M
(0x4B42)
N/ASF550X-48MP
48-Port 10/100
PoE Stackable
Managed Switch
SF550X-48MP
af/at/60wN/A4* PD69208
(0x4AC2) /
4*69208M
(0x4B42)
N/ASG550X-24P
24-Port Gigabit
PoE Stackable
Managed Switch
SG550X-24P
af/at/60wN/A4* PD69208
(0x4AC2) /
4*69208M
(0x4B42)
N/ASG550X-24MP
24-Port Gigabit
PoE Stackable
Managed Switch
SG550X-24MP
Cisco 350 & 550 Series Managed Switches Administration Guide
5
Get To Know Your Switch
Power over Ethernet Considerations
PoE PSE
AF/AT/60W
PoE PD
AF/AT/60W
PoE PSE Chipset
Type
PoE PD Chipset
Type
DescriptionSKU Name
af/at/60wN/A4* PD69208
(0x4AC2) /
4*69208M
(0x4B42)
N/ASG550X-24MPP
24-Port Gigabit
PoE Stackable
Managed Switch
SG550X-24MPP
af/at/60wN/A7* PD69208
(0x4AC2) /
7*69208M
(0x4B42)
N/ASG550X-48P
48-Port Gigabit
PoE Stackable
Managed Switch
SG550X-48P
af/at/60wN/A7* PD69208
(0x4AC2) /
7*69208M
(0x4B42)
N/ASG550X-48MP
48-Port Gigabit
PoE Stackable
Managed Switch
SG550X-48MP
Consider the following when connecting a PoE switch. The PoE switches are PSE (Power Sourcing Equipment)
that are capable of supplying DC power to attaching powered devices (PD). These devices include VoIP
phones, IP cameras, and wireless access points. The PoE switches can detect and supply power to pre-standard
legacy PoE PD. Due to the PoE legacy support, it is possible that a PoE switch acting as a PSE may mistakenly
detect and supply power to an attaching PSE, including other PoE switches, as a legacy PD. Even though PoE
switches are PSE, and as such should be powered by AC, they could be powered up as a legacy PD by another
PSE due to false detection. When this happens, the PoE switch may not operate properly and may not be able
to properly supply power to its attaching PDs.
To prevent false detection, you should disable PoE on the ports on the PoE switches that are used to connect
to PSEs. You should also first power up a PSE device before connecting it to a PoE switch. When a device
is being falsely detected as a PD, you should disconnect the device from the PoE port and power recycle the
device with AC power before reconnecting its PoE ports.
Caution
Front Panel
The following components are found on the front panel of the device:
USB Port—The USB port connects the switch to a USB device so that you can save and restore the
configuration files, firmware images, and SYSLOG files through the connected USB device. The USB
port supports the FAT32 file system.
RJ-45 Ethernet Ports—The RJ-45 Ethernet ports connect network devices, such as computers, printers,
and access points, to the switch.
Multigigabit Ethernet Ports—Highlighted in blue, these ports support speeds of 100 Mbps, 1 Gbps, 2.5
Gbps, and 5 Gbps on Cat 5e cables. Some uplink ports also support MultiGiga speed. In this case, port
speed can reach 10Gbps. Much of the cabling deployed worldwide is limited to 1 Gbps at 100 meters.
Cisco Multigigabit Ethernet enables speeds up to 2.5 or 5 Gbps on the same infrastructure without
replacing a cable.
Cisco 350 & 550 Series Managed Switches Administration Guide
6
Get To Know Your Switch
Front Panel
60-Watt PoE Ports—Highlighted in yellow. The 60-Watt PoE ports double the PoE power to 60W. This
is not found on the 250 devices nor on the SF350-48P device.
SFP+ Port (if present)—The small form-factor pluggable plus (SFP+) are connection points for modules
so that the switch can link to other switches. These ports are also commonly referred to as mini 10GigaBit
Interface Converter ports. The term SFP+ is used in this guide.
The SFP+ ports are compatible with the following Cisco SFP 1G optical modules MGBSX1,
MGBLH1, MGBT1, as well as other brands.
The Cisco SFP+ 10G optical modules that are supported in the Cisco switches are: SFP-10G-SR,
SFP-10G-LR, SFP-10G-SR-S, and SFP-10G-LR-S.
The Cisco SFP+ Copper Cable modules that are supported in the Cisco switches are:
SFP-H10GB-CU1M, SFP-H10GB-CU3M, and SFP-H10GB-CU5M.
The SFP+ port is a combination port, shared with one other RJ-45 port. When the SFP+ is active,
the adjacent RJ-45 port is disabled.
The LEDs of the corresponding RJ-45 port flash green to respond to the SFP interface traffic.
Some SFP interfaces are shared with one other RJ-45 port, called a combo port. When the SFP is active,
the adjacent RJ-45 port is disabled.
OOB Port (if present)—The Out of Band (OOB) port is a CPU Ethernet port that can be used only as a
management interface. Bridging between the OOB port and the in-band Layer 2 interface is not supported.
This does not appear on 250 devices.
Front Panel LEDs
The following are the global LEDs found on the devices:
System—(Green) The LED lights steady when the switch is powered on, and flashes when booting,
performing self-tests, or acquiring an IP address. If the LED flashes Amber, the switch has detected a
hardware failure, a firmware failure, and/or a configuration file error.
System LED - Every 20 seconds, the System LED will flash according to unit ID of the member unit.
Flash = LED going off and then on again.
According to unit ID of the unit. This means
Unit 1 (if not active unit) - system LED will flash 1 time
Unit 2 (if not active unit) - system LED will flash 2 times
Unit 3 - system LED will flash 3 times
Unit 4 -system LED will flash 4 times;
The duration of each flash (LED off time) will be as follows:
LED off time (in each flash) ~ 0.5 seconds.
“Interim” LED on (between 2 LED offs) ~ 0.5 seconds
Cisco 350 & 550 Series Managed Switches Administration Guide
7
Get To Know Your Switch
Front Panel LEDs
For example, the flash duration on the mamber 3 will be ~ 2.5 seconds [(3 LED off *0.5 seconds)
+ (2 “interim LED on” *0.5 seconds) = ~ 2.5 seconds).
The flash on all member units will occur simultaneously. This means that the 1st flash on all member
units will occur at the same time, the 2nd flash (for units 2 and up) at the same time.
The 20 second interval will be counted from the occurrence of the 1st flash on all member units.
This will allow the next flash cycle to begin at the same time on all units.
If a member unit is removed from the stack, its system LED will continue to flash according to
above definition.
The following are per port LEDs:
LINK/ACT—(Green) Located on the left of each port. The LED lights steady when a link between the
corresponding port and another device is detected, and flashes when the port is passing traffic.
SFP+ (if present)—(Green) Located on the right of a 10G port. The LED lights steady when a connection
is made through the shared port, and flashes when the port is passing traffic.
Configuring Switches
The switch can be accessed and managed by two different methods; over your IP network using the web-based
interface, or by using the switch’s command-line interface through the console port. Using the console port
requires advanced user skills.
The following table shows the default settings used when configuring your switch for the first time.
Default ValueParameter
ciscoUsername
ciscoPassword
192.168.1.254LAN IP
Configuring Your Switch Using the Web-based Interface
To access the switch with a web-based interface, you must know the IP address that the switch is using. The
switch uses the factory default IP address of 192.168.1.254, with a subnet of /24. When the switch is using
the factory default IP address, the System LED flashes continuously. When the switch is using a DHCP
server-assigned IP address or an administrator has configured a static IP address, the System LED is a steady
green (DHCP is enabled by default).
If you are managing the switch through a network connection and the switch IP address is changed, either by
a DHCP server or manually, your access to the switch will be lost. You must enter the new IP address that
the switch is using into your browser to use the web-based interface. If you are managing the switch through
a console port connection, the link is retained.
To configure the switch using the web-based interface:
Step 1 Power on the computer and your switch.
Cisco 350 & 550 Series Managed Switches Administration Guide
8
Get To Know Your Switch
Configuring Switches
Step 2 Connect the computer to any network port.
For Cisco 350-550 XG switches, connect the computer to the OOB port found on the front panel.
Note
Step 3 Set up the IP configuration on your computer.
a) If the switch is using the default static IP address of 192.168.1.254/24, you must choose an IP address for the computer
in the range of 192.168.1.2 to 192.168.1.253 that is not already in use.
b) If the IP addresses will be assigned by DHCP, make sure that your DHCP server is running and can be reached from
the switch and the computer. You may need to disconnect and reconnect the devices for them to discover their new
IP addresses from the DHCP server.
Details on how to change the IP address on your computer depend upon the type of architecture and operating
system that you are using. Use your computers local Help and Support functionality and search for “IP
Addressing.”
Note
Step 4 Open a web browser window.
Step 5 Enter the switch IP address in the address bar and press Enter. For example, http://192.168.1.254.
Step 6 When the login page appears, choose the language that you prefer to use in the web-based interface and enter the username
and password.
The default username is cisco. The default password is cisco. Usernames and passwords are both case sensitive.
Step 7 Click Log In.
If this is the first time that you have logged on with the default username and password, the Change username and Password
page opens. The rules for constructing a new password are displayed on the page.
Step 8 Enter a new username and password and confirm.
Password complexity is enabled by default. The password must comply with the default complexity rules.
Note
Step 9 Click Apply.
Make sure that any configuration changes made are saved before exiting from the web-based interface by
clicking on the Save icon. Exiting before you save your configuration results in all changes being lost.
Caution
The Getting Started page opens. You are now ready to configure the switch. Refer to the Administration Guide or see
the help pages for further information.
Browser Restrictions
If you are using IPv6 interfaces on your management station, use the IPv6 global address and not the IPv6
link local address to access the device from your browser.
Configuring Your Switch Using the Console Port
To configure the switch using the console port, proceed with the following steps:
Step 1 Connect a computer to the switch console port using a Cisco console cable (purchased separately).
Step 2 Start a console port utility such as HyperTerminal on the computer.
Cisco 350 & 550 Series Managed Switches Administration Guide
9
Get To Know Your Switch
Configuring Your Switch Using the Console Port
Step 3 Configure the utility with the following parameters:
115200 bits per second
8 data bits
no parity
1 stop bit
no flow control
Step 4 Enter a username and password. The default username is cisco, and the default password is cisco. Usernames and passwords
are both case sensitive.
If this is the first time that you have logged on with the default username and password, the following message appears:
Please change your username AND password from the default settings. Change of credentials
is required for better protection of your network.
Please note that new password must follow password complexity rules
Step 5 Set a new administrator username and password.
Make sure that any configuration changes made are saved before exiting.
Caution
You are now ready to configure the switch. See the CLI Guide for your switch.
If you are not using DHCP on your network, set the IP address type on the switch to Static and change the static
IP address and subnet mask to match your network topology. Failure to do so may result in multiple switches
using the same factory default IP address of 192.168.1.254.
Note
Console access also provides additional interfaces for debug access which are not available via the web interface. These
debug access interfaces are intended to be used by a Cisco Support Team personnel, in cases where it is required to debug
device’s behavior. These interfaces are password protected. The passwords are held by the Cisco support team. The device
supports the following debug access interfaces:
U-BOOT access during boot sequence
Linux Kernel access during boot sequence
Run time debug modes - allows Cisco support team to view device settings and apply protocol and layer 1 debug
commands and settings. The run time debug mode is accessible over telnet and SSH terminals in addition to console.
Restoring Factory Default Settings
To restore the switch to factory default settings, use the Reset button to reboot or reset the switch and do the
following:
To reboot the switch, press and hold the Reset button for less than ten seconds.
To restore the switch to its factory default settings:
Disconnect the switch from the network or disable all DHCP servers on your network.
Cisco 350 & 550 Series Managed Switches Administration Guide
10
Get To Know Your Switch
Restoring Factory Default Settings
With the power on, press and hold the Reset button for more than ten seconds.
Out-Of-Band Port
The switch supports an Out-of-Band (OOB) port which is used for the management network. The out-of-band
and the in-band ports share the same IP routing table. Thus, the same subnet can not be used on both the
in-band and out-of-band interfaces.
The OOB port is assigned an MAC address which differs from the base MAC address and the in-band ports
addresses. This MAC address is used as the source MAC address in all frames sent by the switch on the OOB
port. The IP address assigned to this port cannot be assigned to the in-band ports at the same time. In addition,
it must not belong to any IP subnet configured at the in-band interfaces of the devices.
By default, the OOB port is configured with a default IP address 192.168.1.254. This default IP address is
used when no other address is assigned (dynamically or statically). This subnet is a reserved one and cannot
be assigned on the in-band interfaces.
Stacking the Switches
A stack can have multiple devices in it. Any 10G port of the switch can be used for stacking.
By default, the ports on the switch function as regular Ethernet ports, except if you configure them to do
stacking. You cannot mix the stack speeds between the switches or ports.
Stack ports must be either configured with the same port speed or have the same speed capability on the
module or cable plug in. If the port speed is configured as auto, then the module plugged into these two ports
will need to have the same speed capability, otherwise the switch will not be able to form as a stack with
multiple units.
Danger
The switch can only be stacked without Mesh topology. The switches in the same stack are connected together
through their stack ports. Depending on the type of stack ports and the desired speed, you may need Cat6a
Ethernet cables or Cisco approved modules or cables for the switches.
Product Models
The following are the available product models:
Table 2: Product Models
DescriptionSKU Name
SF350-08 8-Port 10/100 Managed SwitchSF350-08
SF352-08 8-Port 10/100Managed SwitchSF352-08
SF352-08P 8-Port 10/100 PoE Managed SwitchSF352-08P
Cisco 350 & 550 Series Managed Switches Administration Guide
11
Get To Know Your Switch
Out-Of-Band Port
DescriptionSKU Name
SF352-08MP 8-Port 10/100 PoE Managed SwitchSF352-08MP
SF350-24 24-Port 10/100 Managed SwitchSF350-24
SF350-24P 24-Port 10/100 PoE Managed SwitchSF350-24P
SF350-24MP 24-Port 10/100 PoE Managed SwitchSF350-24MP
SF350-48 48-Port 10/100 Managed SwitchSF350-48
SF350-48P 48-Port 10/100 PoE Managed SwitchSF350-48P
SF350-48P 48-Port 10/100 PoE Managed SwitchSF350-48P
SF350-48MP 48-Port 10/100 PoE Managed SwitchSF350-48MP
SG352-10-E 10-Port Gigabit Managed SwitchSG352-10-E
SG352-10P 10-Port Gigabit PoE Managed SwitchSG352-10P
SG355-10P 10-Port Gigabit PoE Managed SwitchSG355-10P
SG352-10MP-E 10-Port Gigabit PoE Managed SwitchSG352-10MP-E
SG352-20 20-Port Gigabit Managed SwitchSG352-20
SG352-28 28-Port Gigabit Managed SwitchSG352-28
SG352-28P 28-Port Gigabit PoE Managed SwitchSG352-28P
SG352-28MP 28-Port Gigabit PoE Managed SwitchSG352-28MP
SG352-52 52-Port Gigabit Managed SwitchSG352-52
SG352-52P 52-Port Gigabit PoE Managed SwitchSG352-52P
SG352-52MP 52-port Gigabit PoE Managed SwitchSG352-52MP
SG352X-24 24-Port Gigabit Stackable Managed
Switch
SG352X-24
SG352X-24P 24-Port Gigabit PoE Stackable Managed
Switch
SG352X-24P
SG352X-24MP 24-Port Gigabit PoE Stackable
Managed Switch
SG352X-24MP
SG352X-48 48-Port Gigabit Stackable Managed
Switch
SG352X-48
SG352X-48P 48-Port Gigabit PoE Stackable Managed
Switch
SG352X-48P
Cisco 350 & 550 Series Managed Switches Administration Guide
12
Get To Know Your Switch
Product Models
DescriptionSKU Name
SG352X-48MP 48-Port Gigabit PoE Stackable
Managed Switch
SG352X-48MP
SX350X-08 8-Port 10GBase-T Stackable Managed
Switch
SX350X-08
SX350X-12 12-Port 10GBase-T Stackable Managed
Switch
SX350X-12
SX350X-24F 24-Port 10G SFP+ Stackable Managed
Switch
SX350X-24F
SX350X-24 24-Port 10GBase-T Stackable Managed
Switch
SX350X-24
SX350X-52 52-Port 10GBase-T Stackable Managed
Switch
SX350X-52
Table 3: Product Models
DescriptionSKU Name
SG550XG-8F8T 16-Port 10G Stackable Managed
Switch
SG550XG-8F8T
SG550XG-24T 24-Port 10GBase-T Stackable
Managed Switch
SG550XG-24T
SG550XG-48T 48-Port 10GBase-T Stackable
Managed Switch
SG550XG-48T
SG550XG-24F 24-Port 10G SFP+ Stackable Managed
Switch
SG550XG-24F
SF550X-24 24-Port 10/100 Stackable Managed
Switch
SF550X-24
SF550X-24P 24-Port 10/100 PoE Stackable Managed
Switch
SF550X-24P
SF550X-24MP 24-Port 10/100 PoE Stackable
Managed Switch
SF550X-24MP
SF550X-48 48-Port 10/100 Stackable Managed
Switch
SF550X-48
SF550X-48P 48-Port 10/100 PoE Stackable Managed
Switch
SF550X-48P
SF550X-48MP 48-Port 10/100 PoE Stackable
Managed Switch
SF550X-48MP
Cisco 350 & 550 Series Managed Switches Administration Guide
13
Get To Know Your Switch
Product Models
DescriptionSKU Name
SG550X-24 24-Port Gigabit Stackable Managed
Switch
SG550X-24
SG550X-24P 24-Port Gigabit PoE Stackable Managed
Switch
SG550X-24P
SG550X-24MP 24-Port Gigabit PoE Stackable
Managed Switch
SG550X-24MP
SG550X-24MPP 24-Port Gigabit PoE Stackable
Managed Switch
SG550X-24MPP
SG550X-48 48-Port Gigabit Stackable Managed
Switch
SG550X-48
SG550X-48P 48-Port Gigabit PoE Stackable Managed
Switch
SG550X-48P
SG550X-48MP 48-Port Gigabit PoE Stackable
Managed Switch
SG550X-48MP
SX550X-16FT 16-Port 10G Stackable Managed
Switch
SX550X-16FT
SX550X-12F 12-Port 10G SFP+ Stackable Managed
Switch
SX550X-12F
SX550X-24 24-Port 10GBase-T Stackable Managed
Switch
SX550X-24
SX550X-24FT 24-Port 10G Stackable Managed
Switch
SX550X-24FT
SX550X-24F 24-Port 10G SFP+ Stackable Managed
Switch
SX550X-24F
SX550X-52 52-Port 10GBase-T Stackable Managed
Switch
SX550X-52
Navigation
The navigation menu, located at the top right of each UI page, lists the device’s main features.You can access
each feature’s UI pages using a series of cascading menus. To access an individual UI page, click the
corresponding feature tab in the navigation menu to display a menu of subcategories. Select a subcategory
and repeat this process until you see the desired page, and then select the page to display it in the main window.
Cisco 350 & 550 Series Managed Switches Administration Guide
14
Get To Know Your Switch
Navigation
Basic or Advanced Display Mode
The product supports many features, and therefore the WEB GUI includes hundreds of configuration and
display pages. These pages are divided into the following display modes:
Basic—Basic subset of configuration options are available. If you are missing some configuration option,
select the Advanced mode in the device header.
Advanced—Full set of configuration options are available.
When the user switches from basic to advanced, the browser reloads the page. However, after reload, the user
stays on the same page. When the user switches from advanced to basic, the browser reloads the page. If the
page exists also on the basic mode, the user stays on the same page. If the page does not exist in the basic
mode, the browser will load the first page of the folder which was used by the user. If the folder does not
exist, the Getting Started page will be displayed.
If there is advanced configuration, and the page is loaded in basic mode, a page-level message will be displayed
to the user (e.g. there are 2 radius server configured but in basic mode only a single server can be displayed,
or there is 802.1X port authentication with time range configured but time range is not visible in basic mode).
When switching from one mode to another, any configuration which was made on the page (without Apply)
is deleted.
Cisco 350 & 550 Series Managed Switches Administration Guide
15
Get To Know Your Switch
Basic or Advanced Display Mode
Cisco 350 & 550 Series Managed Switches Administration Guide
16
Get To Know Your Switch
Basic or Advanced Display Mode
CHAPTER 2
Getting Started
This chapter contains the following section:
Getting Started, on page 17
Getting Started
This section will guide you on how to install and manage your device.
Click on Getting Started to access the page where you can use the various links and follow the on-screen
instructions to quickly configure your switch.
Basic or Advanced Display Mode
The switch's WEB GUI includes hundreds of configuration and display pages. These pages are divided into
the following display modes:
Basic—Basic subset of configuration options.
Advanced—Full set of configuration options are available
When switching from one mode to another, any configuration which was made on the page (without Apply)
is deleted.
Initial Setup
Stack Management, on page 58Manage Stack
TCP/UDP Services, on page 270Change Management Applications
and Services
IPv4 Interface, on page 187Change Device IP Address
VLAN Settings, on page 133Create VLAN
Port Settings, on page 111Configure Port Settings
Device Status
System Summary, on page 33System Summary
Cisco 350 & 550 Series Managed Switches Administration Guide
17
Interface, on page 36Port Statistics
Statistics, on page 48RMON Statistics
RAM Memory, on page 55View Log
Quick Access
User Accounts, on page 59Change Device Password
Firmware Operations, on page 70Upgrade Device Software
File Operations, on page 72Backup Device Configuration
MAC-Based ACL, on page 313Create MAC-Based ACL
IPv4-based ACL, on page 315Create IP-Based ACL
QoS Properties, on page 325Configure QoS
Session Sources, on page 44Configure SPAN
There are two hot links on the Getting Started page that take you to Cisco web pages for more information.
Clicking on the Support link takes you to the device product support page, and clicking on the Forums link
takes you to the Support Community page.
Cisco 350 & 550 Series Managed Switches Administration Guide
18
Getting Started
Getting Started
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260
  • Page 261 261
  • Page 262 262
  • Page 263 263
  • Page 264 264
  • Page 265 265
  • Page 266 266
  • Page 267 267
  • Page 268 268
  • Page 269 269
  • Page 270 270
  • Page 271 271
  • Page 272 272
  • Page 273 273
  • Page 274 274
  • Page 275 275
  • Page 276 276
  • Page 277 277
  • Page 278 278
  • Page 279 279
  • Page 280 280
  • Page 281 281
  • Page 282 282
  • Page 283 283
  • Page 284 284
  • Page 285 285
  • Page 286 286
  • Page 287 287
  • Page 288 288
  • Page 289 289
  • Page 290 290
  • Page 291 291
  • Page 292 292
  • Page 293 293
  • Page 294 294
  • Page 295 295
  • Page 296 296
  • Page 297 297
  • Page 298 298
  • Page 299 299
  • Page 300 300
  • Page 301 301
  • Page 302 302
  • Page 303 303
  • Page 304 304
  • Page 305 305
  • Page 306 306
  • Page 307 307
  • Page 308 308
  • Page 309 309
  • Page 310 310
  • Page 311 311
  • Page 312 312
  • Page 313 313
  • Page 314 314
  • Page 315 315
  • Page 316 316
  • Page 317 317
  • Page 318 318
  • Page 319 319
  • Page 320 320
  • Page 321 321
  • Page 322 322
  • Page 323 323
  • Page 324 324
  • Page 325 325
  • Page 326 326
  • Page 327 327
  • Page 328 328
  • Page 329 329
  • Page 330 330
  • Page 331 331
  • Page 332 332
  • Page 333 333
  • Page 334 334
  • Page 335 335
  • Page 336 336
  • Page 337 337
  • Page 338 338
  • Page 339 339
  • Page 340 340
  • Page 341 341
  • Page 342 342
  • Page 343 343
  • Page 344 344
  • Page 345 345
  • Page 346 346
  • Page 347 347
  • Page 348 348
  • Page 349 349
  • Page 350 350
  • Page 351 351
  • Page 352 352
  • Page 353 353
  • Page 354 354
  • Page 355 355
  • Page 356 356
  • Page 357 357
  • Page 358 358
  • Page 359 359
  • Page 360 360
  • Page 361 361
  • Page 362 362
  • Page 363 363
  • Page 364 364
  • Page 365 365
  • Page 366 366
  • Page 367 367
  • Page 368 368
  • Page 369 369
  • Page 370 370
  • Page 371 371
  • Page 372 372
  • Page 373 373
  • Page 374 374
  • Page 375 375
  • Page 376 376
  • Page 377 377
  • Page 378 378
  • Page 379 379
  • Page 380 380
  • Page 381 381
  • Page 382 382
  • Page 383 383
  • Page 384 384
  • Page 385 385
  • Page 386 386
  • Page 387 387
  • Page 388 388
  • Page 389 389
  • Page 390 390
  • Page 391 391
  • Page 392 392
  • Page 393 393
  • Page 394 394
  • Page 395 395
  • Page 396 396
  • Page 397 397
  • Page 398 398
  • Page 399 399
  • Page 400 400
  • Page 401 401
  • Page 402 402
  • Page 403 403
  • Page 404 404
  • Page 405 405
  • Page 406 406
  • Page 407 407
  • Page 408 408
  • Page 409 409
  • Page 410 410
  • Page 411 411
  • Page 412 412
  • Page 413 413
  • Page 414 414
  • Page 415 415
  • Page 416 416

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI