Page is loading ...
NOTICE:
1. Please read this user manual carefully before using this product.
2. PoC is short for “Power over Cable”. Do not plug into RJ45 until connections are
made and tested at both ends.
3. Only use the TEK TPHD402PR or compatible receiver with the TEK 51T-HD.
4. The item “far-end” means the device (e.g. display device, 3rd party RS232 device
etc.) connected with TEK TPHD402PR.
5. Take notice to 4.6 Instructions of VGA Converting Cable when using.
This manual is for operation instruction only, not for any maintenance usage.
Please refer to the dealers for the latest details.
This manual is copyright TEKVOX, INC. All rights reserved. No part of this
publication may be copied or reproduced without the prior written consent of
TEKVOX, INC.
TEK 51T-HD Compact Presentation Switcher
TEKVOX, INC. www.tekvox.com
Table of Contents
1. Introduction ................................................................................................................. 1
1.1 Introduction to TEK 51T-HD ............................................................................... 1
1.2 Features ............................................................................................................ 1
1.3 Package Contents ............................................................................................. 2
2. Product Appearance ................................................................................................... 3
2.1 TEK 51T-HD Front Panel ................................................................................... 3
2.2 TEK 51T-HD Rear Panel ................................................................................... 4
3. System Connection ..................................................................................................... 5
3.1 Installation Precautions ..................................................................................... 5
3.2 System Diagram ................................................................................................ 6
3.3 Connection Procedure ....................................................................................... 6
3.4 Connection of Microphone ................................................................................. 7
3.5 Application ......................................................................................................... 9
4. System Operations ..................................................................................................... 9
4.1 Operations of Buttons ........................................................................................ 9
Resolution Adjusting ................................................................................ 9 4.1.1
Switching Operations ............................................................................. 10 4.1.2
Operation Examples: ............................................................................. 11 4.1.3
Firmware Updating ................................................................................ 11 4.1.4
Volume Adjusting ................................................................................... 11
4.1.5
Using the OSD Menu ............................................................................. 11 4.1.6
4.2 Operations of IR .............................................................................................. 12
IR Remote ............................................................................................. 12 4.2.1
IR Operations ........................................................................................ 13 4.2.2
4.3 Operations of CEC Function ............................................................................ 14
4.4 Operations of RS232 Control ........................................................................... 15
RS232 Communication Commands ...................................................... 16 4.4.1
RS232 Control Modes ........................................................................... 23 4.4.2
4.5 Operations in OSD Menu................................................................................. 25
1. Optional settings ................................................................................................... 25
2. Image settings ...................................................................................................... 25
TEK 51T-HD Compact Presentation Switcher
TEKVOX, INC. www.tekvox.com
3. Audio settings ....................................................................................................... 25
4. System settings .................................................................................................... 25
Option .................................................................................................... 25 4.5.1
Picture ................................................................................................... 27 4.5.2
Sound .................................................................................................... 28 4.5.3
Setup ..................................................................................................... 29 4.5.4
4.6 Instructions of VGA Converting Cable ............................................................. 29
5. Specification ............................................................................................................. 31
6. Panel Drawing .......................................................................................................... 33
7. Troubleshooting & Maintenance ............................................................................... 34
8. Safety Operation Guide ............................................................................................ 35
After-sales Service ........................................................................................................ 36
TEK 51T-HD Compact Presentation Switcher
TEKVOX, INC. 1 www.tekvox.com
1. Introduction
1.1 Introduction to TEK 51T-HD
TEK 51T-HD is a compact presentation switcher / scaler that can be wall mounted in a
podium, teacher’s desk, or under a conference table. The switcher includes the
following:
3 HDMI Inputs
2 VGA or Component inputs
6 Audio inputs to provide for audio insertion
1 Microphone Input with Mic / 48V Phantom / Line selection
Separate Source and Microphone volume controls
1 Audio output
1 HDMI output
1 HDBaseT Lite output 200’ with PoC
1 TPHD402PR HDBaseT Lite PoC receiver
RS232 control from unit or far-end receiver
IR control from unit or receiver
IR routing from receiver
IR transmitting to receiver
1.2 Features
HDCP Compliant
Supports CEC transport commands for each HDMI input
Supports video source auto-switching function
Supports video signal detection for display power control
Bi-directional IR and RS232 control
Selectable output resolutions: 1920x1200, 1920x1080, 1600x1200, 1360x768,
1280x800, 1280x720, 1024x768
VGA video supports C-video, YPbPr, and VGA
Supports online Firmware upgrading
48V phantom power to support condenser microphone
TEK 51T-HD Compact Presentation Switcher
TEKVOX, INC. 2 www.tekvox.com
MIC input supports balance/unbalance signal
3-level MIC input, supports condenser microphone, dynamic microphone, and
wireless microphone.
Controllable via button, IR, and RS232.
Powerful OSD function.
TekMonitor Macro commands
1.3 Package Contents
1 x TEK 51T-HD
2 x Mounting ears (separate from TEK 51T-HD)
1 x Power Adapter (DC 12V)
1 x IR remote
1 x IR receiver
5 x IR emitters
1 x RS232 cable
2 x VGA converting cables (male VGA to female YPbPr, length: 16”)
7 x Captive screw connectors
4 x Screws (black color)
6 x Plastic cushions
1 x User Manual
Notes：Please confirm that the product and accessories are all included. If they are not,
please contact your dealer.
TEK 51T-HD Compact Presentation Switcher
TEKVOX, INC. 3 www.tekvox.com
2. Product Appearance
2.1 TEK 51T-HD Front Panel
1. Power indicator.
Turns red when power is on. Turns green when in standby mode.
2. LCD screen
Shows the real-time system working status.
3. SOURCE/AUTO
Used as video source selection-button. Press to select one source, press again
to select the next source, switching circularly between HDMI1, HDMI2, HDMI3,
VGA1, and VGA2. The LCD screen will show the name of the selected source.
Used as switching mode selection button. Press and hold 7 seconds or more to
enter into Auto-switching mode. Press and hold 7 seconds or more again to
enter into Manual-switching mode.
Note: Setting any VGA port to AV or YPbPr in Manual-switching mode, the system will
not be able to enter in Auto-switching mode. While in Auto-switching mode, setting any
VGA port to AV or YPbPr will automatically enter in Manual-switching mode with LCD
screen and RS232 control Firmware prompting “Not support!”.
4. ENTER
Used to confirm selection in menu.
5. RESO/AUTO
Used as output resolution manual switching button. Select between 1360x768,
1280x800, 1280x720, 1024x768, 1920x1200, 1920x1080, and 1600x1200.
Used as output resolution switching mode selection button. Press and hold 7
seconds or more to enter into Auto-switching mode. Press and hold 7 seconds
or more again to enter into Manual-switching mode.
TEK 51T-HD Compact Presentation Switcher
TEKVOX, INC. 4 www.tekvox.com
6. MENU/FWUPDATE
Used as menu button. Press it to enter the OSD menu.
Used as Firmware updating button. Press and hold 7 seconds or more to enter
into the Firmware updating procedure.
7. VOL- / Menu Left
Used as volume down button.
Used as direction button Menu Left when in menu mode.
8. VOL+ / Menu Right
Used as volume up button.
Used as direction button Menu Right when in menu mode.
9. MIC+ / Menu Up
Used as MIC volume up button.
Used as direction button Menu Up when in menu mode.
10. MIC- / Menu Down
Used as MIC volume down button.
Used as direction button Menu Down when in menu mode.
2.2 TEK 51T-HD Rear Panel
c d
a b
1. AUDIO INPUT
3 HDMI audio and 2 VGA audio inputs. User can choose any one audio (embedded
HDMI audio or external input audio) for HDMI audio input by using RS232
commands.
2. AUDIO OUTPUT
Audio output port. The audio comes from the input audio corresponding to the
selected video source and mixed with MIC audio.
TEK 51T-HD Compact Presentation Switcher
TEKVOX, INC. 5 www.tekvox.com
3. IR OUT
5 ports in total. Connects with IR emitter and is used to control the local source
device or 51T-HD from remote. It switches following the corresponding video source.
4. IR IN
Connects with IR receiver (with carrier wave only). To receive IR signal, send by the
IR remote or remote controller of other input/output device.
5. FIRMWARE
USB port. Connects with USB flash disk or other storage which is with update file
inside, to update the system firmware.
6. RS232
Serial control port. 3p captive screw connector, connects with a control device (such
as a computer) to control TEK 51T-HD or other device connected with TEK
TPHD402PR.
7. 12V DC
Power port. Connects with the 12V DC power adapter.
8. MIC
a) MIC port. Connects with microphone.
b) MIC switch. 3 levels: 48V phantom power mode (connects with condenser
microphone), MIC mode, (connects with dynamic microphone) and LINE mode
(connects with wireless microphone or line audio).
9. VIDEO INPUT
Video input ports, includes 3 HDMI inputs and 2 VGA inputs. VGA ports supports
YPbPr, C-video, and VGA format. Factory default is VGA format.
10. OUTPUT
c) HDMI local output
d) HDBaseT output, supports PoC.
The audio part of the two video ports is the same and mixed with MIC audio and HDMI
embedded audio. If HDMI embedded audio is disabled, then there will be no audio
output through these ports.
3. System Connection
3.1 Installation Precautions
1) System should be installed in a clean environment with normal operating
temperatures and humidity.
2) All of the power switches, plugs, sockets, and power cords should be installed
according to safety standards.
3) All cables should be properly terminated and tested before connecting to the unit.
TEK 51T-HD Compact Presentation Switcher
TEKVOX, INC. 6 www.tekvox.com
4) All devices should be connected before powering the unit on.
3.2 System Diagram
3.3 Connection Procedure
Step1. Connect HDMI source devices (e.g. Blue-ray DVD) to HDMI input ports of TEK
51T-HD with HDMI cable. Connect VGA source device (e.g. PC) to VGA input
ports of TEK 51T-HD with VGA cable.
Step2. Connect the corresponding audio source to the corresponding AUDIO INPUT
port of TEK 51T-HD with audio cable one to one. The audio of HDMI can be
embedded or external by sending RS232 command.
Step3. Connect HDMI display device to HDMI output port of TEK 51T-HD with HDMI
cable.
Step4. Connect TEK TPHD402PR to HDBaseT output port of TEK 51T-HD with Cat 5e
or Cat 6 type cable.
Step5. Connect speaker, headphone, or amplifier to AUDIO OUTPUT port of TEK
51T-HD.
Step6. Connect control device (e.g. PC) to RS232 port of TEK 51T-HD or TEK
TPHD402PR (bi-directional RS232 control, either is available).
TEK 51T-HD Compact Presentation Switcher
TEKVOX, INC. 7 www.tekvox.com
Step7. Both TEK 51T-HD and TEK TPHD402PR have IR IN and OUT. When one model
is used for IR signal receiver, the IR signal must be sent out by the other model.
For example: When “IR IN” of TEK 51T-HD connects with an IR receiver, the IR
transmitter must connect to IR OUT of TPHD402PR.
The IR signal can be transmitted bi-directionally between TEK 51T-HD and
TEK TPHD402PR.
Step8. Select MIC level and connect right microphone to MIC input port. MIC audio will
be transmitted to AUDIO OUTPUT port and mixed with source audio.
Step9. Connect DC12V power adaptor to the power port (TEK TPHD402PR is able to
get power from TEK 51T-HD).
3.4 Connection of Microphone
TEK 51T-HD provides one 3-level microphone input to accommodate different
microphone input modes, including 48V phantom power mode, MIC mode, and LINE
mode.
48V phantom power input
When switched to “48V”, the MIC input provides 48V phantom power. This is only used
for the condenser microphone.
Connection is: “+” connects to positive, “-” connects to negative and “ ” to ground.
MIC input
When switched to “MIC” (low frequency characteristics and wide frequency response in
this mode), the microphone input is used for connecting with the dynamic microphone.
There are two different connections:
1) Unbalanced connection:
“+” and “ ” connect to ground, and “-” connects to signal.
“-” and “ ” connect to ground, and “+” connects to signal.
TEK 51T-HD Compact Presentation Switcher
TEKVOX, INC. 8 www.tekvox.com
2) Balanced connection: “+” connects to positive, “-” connects to negative and “ ”
connects to ground.
LINE input
When switched to “LINE” (low frequency characteristics and wide frequency response in
this mode), the microphone input is used for connecting with line audio or wireless
microphone output. There are two different connections:
Unbalanced connection:
“+” and “ ” connect to ground, and “-” connects to signal.
“-” and “ ” connect to ground, and “+” connects to signal.
b) Balanced connection: “+” connects to positive, “-” connects to negative and “ ”
TEK 51T-HD Compact Presentation Switcher
TEKVOX, INC. 9 www.tekvox.com
connects to ground.
3.5 Application
The TEK 51T-HD is ideal for smaller system applications especially when there is no
need for an equipment rack. The switcher can be mounted under a conference table, on
a wall, or in a teacher’s desk. When used with a TEKVOX Drop-In system, a low cost
and complete mediated classroom system can be created.
4. System Operations
4.1 Operations of Buttons
The buttons are used for output resolution adjusting, switching operations, Firmware
updating, volume adjusting and operations in menus.
Resolution Adjusting 4.1.1
Resolution can supports both auto and manual settings. Press and hold the
RESO/AUTO button for 7 seconds or more to enter into
auto-adjusting/manual-adjusting mode.
Notice:
1. In auto-adjusting mode the TEK 51T-HD uses the EDID of the display to set the
resolution.
If you need to set the resolution of local HDMI display device:
Power off the TEK 51T-HD and break the connection between the TEK 51T-HD and
TEK TPHD402PR.
Turn on the power for the TEK 51T-HD.
Get the resolution of local HDMI output device.
Connect the TEK TPHD402PR to TEK 51T-HD.
2. In auto-switching mode front panel button control is not available, but IR and RS232
control is able to switch modes.
TEK 51T-HD Compact Presentation Switcher
TEKVOX, INC. 10 www.tekvox.com
Switching Operations
4.1.2
The TEK 51T-HD Supports both auto-switching and manual switching. Press and hold
the SOURCE/AUTO button for 7 seconds or more to enter into
auto-switching/manual-switching mode.
The display result is showed as below:
The display result will be shown for 2 seconds.
The auto-switching mode follows the listed principles:
New input principle
Once it detects a new input signal, the TEK 51T-HD switches to this new signal
automatically.
Power rebooting principle
TEK 51T-HD offers this feature to remember the last displayed signal when
rebooting. While rebooting, the TEK 51T-HD automatically enters into auto-switching
mode and detects all inputs to memorize their connection status.
If the signal last displayed is still available, then it will choose the signal to output. If
not, there will be no signal on its outputs.
Signal removing principle
Once it has removed the current display signal, the TEK 51T-HD will detect all input
signals with priority from INPUT 1 to INPUT 5. It will select the first detected signal to
its output.
Notice: The Auto-switching function works only when an input detects a new signal, loss
of a signal, or power rebooting. With any VGA port set to AV or YPbPr the system is not
able to enter in Auto-switching mode.
IN: HDMI1 MANUAL
1280 X 720
IN: HDMI1 AUTO
1280 X 720
Auto-switching function
TEK 51T-HD Compact Presentation Switcher
TEKVOX, INC. 11 www.tekvox.com
Operation Examples:
4.1.3
Connect INPUT 2, INPUT 4, and INPUT 5 ports to their source devices and select
INPUT 4. Press and hold the front key SOURCE/AUTO for 7 seconds or more to enter
into auto-switching mode.
No change on inputs and the output remains on INPUT 4.
Connect INPUT 3 with a source device and the output switches to INPUT 3.
Remove the signal from INPUT 3 and the TEK 51T-HD will search for input signals
on inputs 1 through 5. When it detects INPUT has video, it will choose INPUT 2 to
output.
Cycle power on the TEK 51T-HD and it will select INPUT 2 to output.
Firmware Updating 4.1.4
Firmware updating will update the firmware of this scaler-switcher.
The TEK 51T-HD supports firmware updating via USB flash drive. Use the following to
update:
1) Copy the file “MERGE_51T-HD.bin” to the root directory of a USB flash drive. (Make
sure the file is copied to the root directory for normal use. The “MERGE_51T-HD.bin”
file is provided and authorized by TEKVOX engineering department).
2) Plug the USB flash drive into the TEK 51T-HD USB port on its rear panel.
3) Press the button “MENU” for 7 seconds or more to update the firmware
automatically. If this does not work, you can also use the OSD and select “Software
Update” or send RS232 command 50689%.
4) After unit is finished updating firmware, you need to perform a factory reset by
sending RS232 command 50617%. It might also be possible to use the OSD menu
by pressing Menu then Left and select Restore Factory Default. If the TEK 51T is
controlled from the receiver, then it is necessary to send the command 50788% or
perform the Drop-in Setup procedure.
Volume Adjusting 4.1.5
Volume control uses the same buttons for the OSD menu.
Press VOL -- to decrease line volume, VOL + to increase.
Press MIC – to decrease MIC volume, MIC + to increase.
Using the OSD Menu 4.1.6
Press the MENU button to enter in OSD menu and use the UP, DOWN, LEFT and
RIGHT buttons to select. Press the ENTER button to confirm selection. The MENU
button is also used to exit the OSD menu.
TEK 51T-HD Compact Presentation Switcher
TEKVOX, INC. 12 www.tekvox.com
4.2 Operations of IR
IR Remote 4.2.1
IR signals are transmitted bi-directionally between the TEK 51T-HD and TEK
TPHD402PR. Use the IR remote at the receiver to control the TEK 51T-HD or HDMI
source devices (via CEC function buttons).
ᬅ Standby button
To enter in/exit standby mode.
ᬆ Input channel selection buttons
INPUT 1 is for HDMI1, INPUT 2 for
HDMI2…INPUT 5 for VGA2. AUTO button:
Enable/disable auto-switching mode.
ᬇ Volume adjusting buttons
MIC-/+: decrease/increase MIC volume
LINE-/+: decrease/increase line volume
MIC MUTE: mute/unmute MIC audio
LINE MUTE: mute/unmute line audio
ᬈ Menu operation buttons
MENU: press to enter the OSD menu or return to
the previous menu. EXIT: exit OSD menu.
OK: confirm button. ,,, : UP/DWON/LEFT/
RIGHT button, for value setting or page-turn,
Buttons in area a are also able to work in CEC
mode to enter the menu of HDMI source device.
P.P, ZOOM, S.M: shortcut button, to select display
mode.
ᬉ Resolution selection buttons
Select the resolution by pressing the
corresponding button. AUTO is for auto-selecting
the best resolution.
ᬊ CEC function buttons
These are for the HDMI input signal which
supports CEC. Includes PLAY, PAUSE, STOP,
MENU, REV (reverse) and FWD (forward).
TEK 51T-HD Compact Presentation Switcher
TEKVOX, INC. 13 www.tekvox.com
IR Operations
4.2.2
The 5 IR OUT ports correspond to the 5 video inputs respectively. Routing of IR signals
from the unit or the receiver follow to the video source selection.
1) Control far-end device from local
Control the TEK 51T-HD or far-end display device from an IR receiver at the unit by
using a corresponding remote controller.
TEK 51T-HD Compact Presentation Switcher
TEKVOX, INC. 14 www.tekvox.com
2) Control local device from remote
Control the TEK 51T-HD or local source device from an IR receiver at HDBaseT receiver
by using a corresponding remote controller.
4.3 Operations of CEC Function
The TEK 51T-HD supports CEC commands and can be enabled and disabled through
RS232 commands or the OSD menu. If the HDMI source device supports CEC and its
CEC operation is enabled when the TEK 51T-HD enters in standby / startup mode, then
the source device will automatically enter standby / startup mode.
Devices that support CEC functions can be controlled with basic operations (play, pause,
fast forward, fast reverse, menu, etc.). Users are able to control the TEK 51T-HD and
HDMI source device via the IR remote or RS232 commands from the TEK 51T-HD. Note
that not all CEC enabled devices operate the same and may act differently between
devices.
Commands for CEC function: “50686%” (enable CEC) and “50687%” (disable CEC).
TEK 51T-HD Compact Presentation Switcher
TEKVOX, INC. 15 www.tekvox.com
The working status related to CEC and STANDBY is showed as below:
Situation
Working Status
CEC: on, Standby: on
Press STANDBY button on IR remote: TEK 51T-HD enters in
standby mode, so do all HDMI source devices.
Press STANDBY button again on IR remote, TEK 51T-HD
exits standby mode, only the HDMI source device selected to
starts working.
CEC: on, Standby: off
Press STANDBY button on IR remote: TEK 51T-HD enters in
standby mode, HDMI 1~3 source devices remain on.
CEC: on
Use CEC function buttons, ▲,▼, , and OK buttons on
IR remote to control HDMI source devices including play,
pause, fast forward, fast reverse, and operations in menu.
CEC: off
Unable to control HDMI source devices through IR remote
CEC: Control HDMI source devices by IR remote of TEK 51T-HD
4.4 Operations of RS232 Control
Use the RS232 port on the TEK 51T-HD or TEK TPHD402PR to control the TEK
51T-HD using a third party RS232 device.
TEK 51T-HD Compact Presentation Switcher
TEKVOX, INC. 16 www.tekvox.com
RS232 Communication Commands
4.4.1
Communication protocol: RS232 Communication Protocol
Baud rate: 9600 Data bit: 8 Stop bit: 1 Parity bit: none
Command
Function
Feedback Example
Switch Commands
50701%
Switch to HDMI 1 input
Switch to HDMI 1
50702%
Switch to HDMI 2 input
Switch to HDMI 2
50703%
Switch to HDMI 3 input
Switch to HDMI 3
50704%
Switch to VGA 1/YPbPr 1/AV 1 input
Switch to VGA 1/YPbPr 1/AV 1
50705%
Switch to VGA 2/YPbPr 2/AV 2 input
Switch to VGA 2/YPbPr 2/AV 2
50680%
Select VGA 1 for INPUT 4
Input 4 Set & Switch to VGA 1
50681%
Select YPbPr 1 for INPUT 4
Input 4 Set & Switch to AV 1
50682%
Select AV 1 for INPUT 4
Input 4 Set & Switch to AV 1
50683%
Select VGA 2 for INPUT 5
Input 5 Set & Switch to VGA 2
50684%
Select YPbPr 2 for INPUT 5
Input 5 Set & Switch to YPbPr 2
50685%
Select AV 2 for INPUT 5
Input 5 Set & Switch to AV 2
50785%
Enable auto-switching
Auto Switching
50786%
Disable auto-switching
Manual Switching
Audio Commands
50600%
MUTE line audio
LINE Mute
50601%
Un-Mute line audio
LINE Unmute
50602%
Line audio volume up
LINE Volume: xx
50603%
Line audio volume down
LINE Volume: xx
501xx%
Set the Line volume (xx = 00 to 60)
LINE Volume: xx
50720%
Mute LINE audio & MIC audio
LINE Mute
MIC Mute
50721%
Unmute LINE audio & MIC audio
LINE Unmute
MIC Unmute
50722%
Mute MIC audio
MIC Mute
50723%
Unmute MIC audio
MIC Unmute
50694%
Enable Mic precedence
Mic precedence: enable
图像输出调整关闭
/
