Work Smart TC8860 Operating instructions

Type
Operating instructions
TC8860
STACKING CADDY
OPERATING INSTRUCTIONS
WARNING
1. Do not use this product unless all bolts screws and knobs are
securely tightened.
2. Check that all bolts screws and knobs are tight every three
months or as needed.
3. Dispose of packing material properly. Do not use plastic cover
as head covering. It may cause suffocation.
4. Do not use this product as a stepladder.
5. Use this product for its intended purpose only.
WORK SMART LIMITED WARRANTY
Work Smart products are warranted from the date of purchase against failure due to material and workmanship as follows:
• 15 Years on all non-moving metal parts.
• 5 Years on component parts including Control mechanisms, pneumatic cylinders, wood, plastic parts, base and casters.
• 3 Years on upholstery fabric and foam against wear and deterioration.
• Leather is not warranted against routine scratching and scuffing, as leather is subject to minor blemishes in use.
To make a warranty claim, contact Parts Department. Provide model number, proof of purchase, description of the problem and obtain return authorization.
At it’s option Office Star Products will:
(a) Supply compatible components of current manufacture.
(b) Repair the customer’s component. The customer must prepay freight on any components returned to the factory. Return freight on components
still in warranty will be paid by Office Star Products.
*All warranties are limited to the original purchaser for normal commercial usage defined as a standard forty hour work week by persons weighing 250 lbs. or
less. The BC9601 is for persons weighing 300 lbs. or less. The BC9602 is for persons weighing 400 lbs. or less. The BC9603 is for persons weighing 500 lbs.
or less. EX1098, EC1283C & ECH12801 are for persons weighing 350 lbs. or less. This warranty will not cover labor, freight or damage from misuse, abuse,
negligence, alteration, accident, vandalism, rusting, acts of nature or any other event beyond the control of Office Star Products. The warranty does not cover
cosmetic damage that may result from normal use. Liability for incidental or consequential damages is excluded. The user assumes all risk of injury resulting
from use of this product. When usage is more than 40 hours per week, a two year warranty on all parts applies. Fabric is warranted for one year. This warranty
gives you specific legal rights, and you may also have other rights which vary from state to state.
Our quality standards are among the highest in the industry. Sometimes, no matter how hard we try, there are times when parts are damaged or missing. Our
Parts Department will do everything possible to promptly remedy the problem. Contact us via e-mail parts@officestar.net, by Fax 1-909-930-5629, or toll free
parts number 1-800-950-7262, Monday through Friday 8:00 a.m. - 5:00 p.m. Pacific Time.
© Office Star Products April 2018
Remove all parts from carton, separate by part numbers indicated on parts list, and verify part quantities.
STEP 1 Secure Casters (2) to each corner plate of Frame (1) using four Small Bolts (11) and four Small Washers (13) for each Caster (2).
FULLY TIGHTEN ALL SHORT BOLTS (11).
STEP 2 Attach Lower Poles (4) to Frame (1) using two Long Bolts (12) and two Cap Nuts (16) for each Lower Pole (4).
FULLY TIGHTEN ALL LONG BOLTS (12).
STEP 3 Designate one side of Frame (1) as the front and one side as the rear. Slide Upper Poles A (5) onto front Lower Poles (4).
Secure Upper Poles A (5) using one Stretcher Bar (3), four Long Bolts (12) and four Cap Nuts (16). FULLY TIGHTEN ALL CAP NUTS (16).
Slide Upper Poles B (6) onto rear Lower Poles (4). Secure Upper Poles B (6) using one Stretcher Bar (3), four Long Bolts (12) and four
Cap Nuts (16). FULLY TIGHTEN ALL CAP NUTS (16). Slide Top Cap A (9) onto Upper Poles A (5). Slide Top Cap B (10) onto Upper Poles B (6).
STEP 4 Attach Cross Bar A (7) to Top Cap A (9) and Top Cap B (10), secure using one Large Washer (14) and one Safety Pin (17).
Attach Cross Bar B (8) to Top Cap A (9) and Top Cap B (10), secure using one Large Washer (14) and one Safety Pin (17).
ATTENTION: MAKE SURE ALL NUTS AND BOLTS ARE FULLY TIGHTENED BEFORE USING.
PART QTY
1. Frame .............................1
2. Caster .............................4
3. Stretcher Bar ........................2
4. Lower Pole ..........................4
5. Upper Pole A ........................2
6. Upper Pole B ........................2
7. Cross Bar A .........................1
8. Cross Bar B .........................2
9. Top Cap A ..........................1
10. Top Cap B .........................1
11. Short Bolt .........................16
12. Long Bolt .........................16
13. Small Washer .....................32
14. Large Washer ......................2
15. Nut ..............................16
16. Cap Nut ..........................16
17. Safety Pin .........................2
18. Key Wrench ........................2
19. Allen Wrench .......................1
TC8860
STACKING CADDY
ASSEMBLY INSTRUCTIONS
TC8860
STACKING CADDY
ASSEMBLY INSTRUCTIONS
16
5
6
18
15
13
1
4
9
510
6
12
17
14
8
7
16
3
12
1
2
13
11
STEP 1
STEP 2
STEP 3
REAR
REAR
FRONT
FRONT
STEP 4
  • Page 1 1
  • Page 2 2

Work Smart TC8860 Operating instructions

Type
Operating instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI