Plymovent Mini Rail Profile (MRP) User manual

Type
User manual

Plymovent Mini Rail Profile (MRP)

The Plymovent Mini Rail Profile (MRP) is a flexible exhaust extraction rail for several vehicles, equipped with a number of extraction units. It is designed for use with passenger cars and light commercial vehicles, and can connect multiple stationary vehicles. The MRP features manual connection/disconnection of exhaust nozzles, and can be installed on either the ceiling or wall.

The MRP is made of extruded aluminum and has a weight capacity of 270 kg. The hose is made of thermoplastic material with a nylon helix, and is crush resistant with a temperature range of -30°C to 150°C. The rubber seal is made of EPDM rubber with low friction material, and the trolley has wheels with ball bearings.

Plymovent Mini Rail Profile (MRP)

The Plymovent Mini Rail Profile (MRP) is a flexible exhaust extraction rail for several vehicles, equipped with a number of extraction units. It is designed for use with passenger cars and light commercial vehicles, and can connect multiple stationary vehicles. The MRP features manual connection/disconnection of exhaust nozzles, and can be installed on either the ceiling or wall.

The MRP is made of extruded aluminum and has a weight capacity of 270 kg. The hose is made of thermoplastic material with a nylon helix, and is crush resistant with a temperature range of -30°C to 150°C. The rubber seal is made of EPDM rubber with low friction material, and the trolley has wheels with ball bearings.

Product manual
MRP
List of contents
Area of application ...........2
Technical data ..................2
Safety instructions .............3
Installation ....................4-6
Maintenance ....................7
Spare parts ................... 8-9
Contact us ...................... 10
PUM_MRP_040826_EN
2 / 10
270 kg
205 kg 150 kg 150 kg
150 kg 150 kg
AREA OF APPLICATION
A flexible exhaust extraction rail for several vehicles,equipped with a number of extraction units.
- for passenger cars and light commercial vehicles
- several stationary vehicles can be connected
- manual connection/disconnection of exhaust nozzles
UNIT DESCRIPTION
Rail: Made of extruded aluminum.
Hose: Made of thermoplastic material with a nylon
helix - crush resistant.
Temp range -30°C to 150°C.
Rubberseal: EPDM- Rubber with low friction material.
Trolley: Wheel with ball bearings.
WEIGHT INFO
Rail Incl. seal: 5.6kg/m
Trolley Incl.hose: 7,5kg
Installation
On ceiling or wall
Maintenance
Only light service and maintenance
is required.See page 7 in manual.
Function
3 / 10
INSTALLATION
Use approved Work-platform or Scaffold
Warning-unauthorized personnel are not allowed to stay near to installation-area.
Note! Load on support legs. see page2.
Note! Mount End- cover directly after Trolley (MIC-100) has been installed
IN OPERATION
Note! It is not allowed to hang up irrelevant material in MRP-profile.
SERVICE—MAINTENANCE
Use approved Work-platform or Scaffold.
Check that End- cover is replaced after service of Crab(MIC-100).
Safety Instructions
4 / 10
1.a 1.b
3.a
3.a
4.a 4.b
Max 5m Max 5m
M8
2.a
3.b
Installation
5 / 10
5.a 5.b
70mm 70mm
15mm
15mm
73mm
40mm
M8
M8
Ø9mm
6.a
6.b
7.a
Ø9mm
M8
8.a 8.b
8.a
6.b
5.c
Installation
6 / 10
x6
9.a
10.a
10.a
10.c
10.e
10.d
Installation
7 / 10
4,5
3
6
1,2,3
1. Clean the inside of the rail where the trolley wheels are running.
2. Clean the inside of rubber seal.
3. Check the trolley, clean the wheels.
4. Check balancer-support, wire and safety chain.
5. Balancer spring tension is to be adjusted when needed, se separate manual for
balancer.
6. Check the hose suspension belt and the nozzle. Line up ( adjust belt and nozzle)
Maintenance
8 / 10
1
2
3
4
5
Spare Parts
Date: April -04
MRP-RAIL/CRAB MIC-100
Produkt No:
Decription
AAll models All models of MRP
BMRP
CMIC-100
D
E
F
G
H
I
Abbreviation
X =Order as required, state required length.
Pos
Art. No:
A
B
C
D
E
G
H
I
Description
Note
14-1740 1Suction Cone
2968 669 1Rubber Bumber
34-1738 1Wheel Incl. Bearings
44-1739 1Distance
54-1735 1MRP / support
When ordering spare parts please quote:
€Product No. (see label) Batch No Description Part No Quantity
For example:
MRP / support 4-1735
Copyright: All right reserved. All information within this printed matter may not be
reproduced, handed over, copied, xeroxed or translated into another language, in any form or
any means without written permission from PlymoVent AB. PlymoVent AB reserves the right to
make design changes.
SPARE PARTS LIST
MHR/Eng/27/
10 / 10
Återförsäljare / Distributör/ Distribuidor
Representative / Distributeur
Address and telephone Dirección y telefóno
Adress och telefon
Adresse und telefon
Adresse et téléphone
Head office / Factory
PlymoVent GmbH
Heideweg 24
D-53604 Bad Honnef, Germany
Tel: +49 2224 97 300
Fax: +49 2224 89 646
info@plymovent.de
www-plymovent.de
PlymoVent Ltd
Marley Way, Southam Road
Banbury, OX16 2RA, England
Tel: +44 1295 25 93 11
Fax: +44 1295 27 17 50
info@plymovent.co.uk
www.plymovent.co.uk
PlymoVent SAS
B.P. 30, Zone Industrielle de Mavault
F-86170 Neuville de Poitou, France
Tel: +33 549 51 55 88
Fax: +33 549 51 59 33
info@plymovent.fr
www.plymovent.fr
PlymoVent AB
P.O. Box 527
SE-921 28 Lycksele, Sweden
Tel: +46 950 57 67 00
Fax: +46 950 57 67 90
info@plymovent.se
www.plymovent.se
Sales office
USA Canada
England
Deutschland
France
PlymoVent AB
Tangenten 2, Industrigatan 26,
SE-212 14 MALMÖ
, Sweden
Tel: +46 40 30 31 30
Fax: +46 40 30 31 40
info@plymovent.se
www.plymovent.se
PlymoVent Corp.
115 Melrich Road
Cranbury, New Jersey 08512, USA
Tel. +1 (609) 395-3500
Fax. +1 (609) 655-0919
info@plymoventusa.com
Year established: 1989
PlymoVent Canada Inc.
24-1200 Aerowood Dr.
Mississauga, ON L4W 257, Canada
Tel: +1 (905) 564-4748
Fax: +1 (905) 564-4609
www.plymovent.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

Plymovent Mini Rail Profile (MRP) User manual

Type
User manual

Plymovent Mini Rail Profile (MRP)

The Plymovent Mini Rail Profile (MRP) is a flexible exhaust extraction rail for several vehicles, equipped with a number of extraction units. It is designed for use with passenger cars and light commercial vehicles, and can connect multiple stationary vehicles. The MRP features manual connection/disconnection of exhaust nozzles, and can be installed on either the ceiling or wall.

The MRP is made of extruded aluminum and has a weight capacity of 270 kg. The hose is made of thermoplastic material with a nylon helix, and is crush resistant with a temperature range of -30°C to 150°C. The rubber seal is made of EPDM rubber with low friction material, and the trolley has wheels with ball bearings.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI