Coleman XP41001 Operating instructions

Brand: Coleman

Model: XP41001

Type: Operating instructions

Application and Instruction Manual

Motion Activated

Solar Powered LED Post Lamp

MODEL: XP-41001

Introduction

IMPORTANT

Read this manual carefully before assembling, using or servicing this unit. Keep

this manual for future reference. If you have questions about assembly, operation,

servicing or repair, please call Apex at 1-866-427- 3946.

Thank you for purchasing the Coleman Solar Powered Post Lamp. This post lamp

will provide years of clean, energy free lighting powered by the sun. Simply

assemble and place the solar post lamp in a shade free area that will receive

maximum sunlight and enjoy. The post lamp utilizes LED’s (Light Emitting

Diodes) that never need to be replaced. To operate, simply press the ON button

located on the underside of the post lamp head (see fig 1).

During daylight hours, the solar panel will harvest

sunlight and store the energy in rechargeable

lithium batteries (The post lamp will not illuminate

during daylight hours). A photo cell will

automatically turn the post lamp on at

nightfall. There is a white motion detector located

on the underside of the post lamp head (See fig.2.)

Make sure the motion detector is facing the

direction of the most activity.

To conserve energy, the post lamp will illuminate at

maximum power for approximately 1 minute. The

solar post lamp will then go into conservation mode

and the light output will be reduced. When motion

is detected the post lamp will return to maximum

light output.

Please make sure to securely mount the base to

a solid surface with the enclosed expanding bolts.

For wood surfaces, the base can be secured using

common 4” lag bolts.

Installation Instructions

Please read and follow the instructions carefully.

1. Carefully remove all parts from the carton and place them on a smooth, stable

surface.

2. Attach lower stem (B) into base (A) by inserting screws into the predrilled holes

with the provided Allen Wrench (Diagram C)

3. Thread the upper stem (C) to the (A,B) assembly by turning clockwise until tight

(Diagram D)

4. Thread the solar post head (D) on to (A,B,C) assembly by turning clockwise

until tight.

5. Unit must be securely mounted to a solid surface with the enclosed expanding

bolts. For wood surfaces, the base can be secured using common 4” lag bolts.

Functions

For best results, place the unit in an area that receives maximum sunlight. When

determining the permanent location for your solar post lamp keep in mind that

landscaping, housing, or other structures may create shadows at different times

during the day or season that can dramatically reduce solar collection.

For normal operation press the On/Off switch. During daylight hours, the solar

panel will harvest energy from the sun, and store the energy in rechargeable

Lithium batteries. At night, the light sensor will automatically turn the post lamp on.

After 1 minute of illumination at full power, the lamp post will enter a conservation

mode with a reduced light output. When motion is detected the lamp will return

to full power for approximately 1 minute and repeat the cycle.

Precautions

1. Avoid touching the top surface of the solar-powered light.

2. If the light is not working properly check it by covering the upper surface of the

solar panel completely in order to activate the light sensor.

3. This type of light has been designed to work in the dark. If there is a high level

of ambient light nearby (street lamps, house lights, landscape lighting, etc.) the

LED light may appear very dim or may not turn on at all.

4. Even though the battery has been charged by the manufacturer, its charge level

may have dropped during transit.

A full day in bright sunshine will return the unit to peak performance.

Specifications

Rechargeable Battery: 7.4V/1500mah lithium-polymer battery

Solar Charging Panel: 10V/2.5W Monocrystalline

Continuous Illumination Time: >14 hours

Complies with FCC Part 15 Class B

Color temperature: 6000K~7000K

Motion distance: <3m

Motion range:160°

Switch model: OFF-ON

This product is intended for outdoor use only.

Replacing Batteries:

The Lithium batteries inside your Post Lamp will last approximately 2 years

(depending on the number of cycles), and will eventually need to be replaced.

Only use batteries from Xepa Technologies to ensure compatibility. (Refer to the

product’s original battery for correct size.)

The battery should be positioned so it has the correct polarity (+) and (-).

Recycle the old battery, or dispose of it in accordance with local, state and federal

regulations. Never dispose of batteries in trashcans or by fire.

Product Warranty & Support Information:

For customer support call (866) 427-3946 or visit www.apexdigitalinc.com.

This product comes with a limited warranty of 1 year from the day of purchase.

(Proof of the date of purchase must be provided if the product is returned.) If the

product is found to be defective in material or workmanship, APEX will replace

the defective part(s). If any of the product parts are found to be missing, please

contact APEX within ten (10) days of purchase.

FCC Part 15 Class B

CAUTION: Modifications are not approved by the party responsible for

compliance and could void user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for

Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio or television reception.

The user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Thank you for your purchase. We appreciate your business.

XEPA TECHNOLOGIES by

APEX DIGITAL INC.

301 Brea Canyon Rd.

Walnut, California 91789

is a registered trademark of The Coleman Company, Inc., used under license.

 2011 The Coleman Company, Inc.

Coleman XP41001 Operating instructions

Coleman XP41001 Operating instructions

Coleman XP41001 Operating instructions

Related papers

Other documents