Page is loading ...
ELECTRIC
KNIFE
GREKNIFE2
INSTRUCTION MANUAL
Please read this manual carefully before using, and keep it for future reference.
CONTENTS
General Safety 4
1. About this guide 5
2. You should have 6
3. How to recognise the parts of your electric carving knife 7
4. How to use your electric carving knife 8
5. How to clean and store your electric knife 10
6. Service 11
7. Specification 11
Customer Support Last Page
4
GENERAL SAFETY
Reading and storing the user manual
This user manual is part of the electric knife (hereinafter also
called “device”). It contains important information on how to set up and
use the device.
Before using the device, read the operating manual carefully, in particular
the safety instructions. Failure to follow this operating manual may
lead to severe injuries or product damage.
This user manual is based on the standards and regulations that are valid
within Australia. Outside Australia, please also note the
country-specific directives and laws.
Keep this operating manual for future reference. If you pass this device
on to a third party, you must also supply this operating manual.
Proper use
This device is intended for private use only and is not suitable for commercial use. Use
the device only as described in this operating manual. Any other use is improper and
may lead to product damage or even personal injury. This device is not a toy.
The manufacturer or retailer assume no liability for damage caused by improper or
incorrect use.
• Do not expose this product to rain or moisture.
• Do not temper or change or modify the product in any way.
• Only use Accessories outlined and recommended by the manufacturer.
• Please do not expose the product to splashing or water contact
IMPORTANT INFORMATION
5
1. ABOUT THIS GUIDE
THIS PRODUCT WAS DESIGNED AND MANUFACTURED TO MEET STRICT QUALITY AND
SAFETY STANDARDS. THERE ARE, HOWEVER, SOME OPERATIONAL PRECAUTIONS THAT
YOU SHOULD BE AWARE OF.
1. The cutting blades are sharp, handle with care. Hold the electric knife using the finger grips
or blade shafts, both when handling the electric knife and cleaning.
2. Always disconnect the appliance from the supply if it is left unattended and before assembling,
disassembling or cleaning.
3. Do not immerse the electrical parts of the appliance in water or other liquids. Never hold the
appliance under running water.
4. Switch o the appliance and disconnect from supply before changing accessories or a
proaching parts that move in use.
5. Never use accessories which are not recommended by the manufacturer. They could
pose a safety risk to the user and might damage the appliance. Only use original parts
and accessories.
6. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
7. Never let the motor unit, power cord or plug get wet.
8. Don’t let excess cord hang over the edge of a table or worktops or touch hot surfaces.
9. Misuse of your electric knife can result in injury.
10. Care is needed when handling the sharp cutting blades and during cleaning.
We’ve written this manual to help you get the most from your electric knife.
Please keep hold of it for future reference.
SAFETY PRECAUTIONS
• Caution is necessary when handling the blades.
• Blades are very sharp.
• Do not allow children to play with blades.
1. Always turn the power o at the power outlet before you insert or remove a plug.
Remove by grasping the plug - do not pull on the cord.
2.Turn the power o and remove the plug when the appliance is not in use and before cleaning.
3.Do not use your appliance with an extension cord unless this cord has been checked and
tested by a qualified technician or service person.
4.This appliance is not intended for use by persons (including children) with reduced.
physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction. Concerning use of the appliance by a person
responsible for their safety.
5.Children should be supervised to ensure that they do not play with the appliance.
6.Do not use an appliance for any purpose other than its intended use.
7. Do not let the power cord of an appliance hang over the edge of a table or bench top or touch
any hot surface.
8.Do not immerse the appliance in water or any other liquid unless recommended.
9. This appliance is intended to be used in household and similar applications such as: sta
kitchen areas in shops, oces and other working environments; farmhouses; by clients in
hotels, motels and other residential type environments; bed and breakfast type environments.
WARNINGS:
6
11. This appliance shall not be used by children. Keep the appliance and its cord out of reach of
children.
12. This appliance can be used by persons with reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and if they understand the hazards involved.
13. Children shall not play with the appliance.
14. Only use the appliance for its intended domestic use.
15. No liability will be accepted if the appliance is subject to improper use or failure to comply
with these instructions.
2. YOU SHOULD HAVE
Electric carving knife,
blades and blade cover
7
3. HOW TO RECOGNISE THE PARTS OF YOUR ELECTRIC CARVING KNIFE
8
4. HOW TO USE YOUR ELECTRIC CARVING KNIFE
Before first use remove the blade cover and carefully wash the blades using a cloth
with warm soapy water or in a dishwasher.
FITTING THE BLADE
1. Check to ensure that the electric knife is not plugged in.
2. Reassemble the blades if necessary.
To do this hold the blades using the finger
grips and place the slot at the end of the
right blade over the rivet one the left blade.
5. Insert the blade shaft into the slots of the
handle using the finger grips. Ensure
the cutting edge of the blades
are facing the same way as the
power switch.
3. Slide the rivet along so that both
finger grips are situated next to each other.
4. For safety carefully place the blade
cover back over the blades.
9
6. Push down until the blades click firmly into
place and blade release buttons pop out.
1. Always place the food to be carved
on a suitable cutting board so worktops
and tabletops are protected from damage.
2. Slot the plug into a power socket and
switch on.
4. When using the electric knife gently push the blade in the direction you wish to cut.
5. When slicing poultry cut almost to the bone and then separate meat from the bone manually.
Do not attempt to cut through bones
6. Do not use the knife for more than 5 minutes. Allow the knife to cool for 1 minute
before continuing
7. The blades are high quality and do not require sharpening.
8. Do not use to cut frozen food.
3. Hold the electric knife in position.
To turn the knife on, place your finger on the
power switch and push the lock switch back
towards (1), then slide the power switch back
towards the base of the handle(2). the lock
button must be held otherwise the knife
will not work.
CARVING MEAT AND FOOD.
10
1. Check to ensure that the electric knife is not
plugged in.
2. Grip the blades firmly using the finger grips
and push in the blade release buttons, a click
will be heard and the blades will be released.
3. Slide the blades out of the handle.
Removing the blades
5. HOW TO CLEAN AND STORE YOUR ELECTRIC KNIFE
Make sure your electric knife is disconnected from the power and is completely
cool.
1. Remove the blades from the handle as detailed elsewhere in there instructions.
2.Separate the blades by sliding the rivet on the left blade out of the slot in the right blade.
3. Carefully wash the blades using warm soapy water or in a dishwasher. Rinse and
dry thoroughly.
4. Wipe the handle with a slightly damp cloth then dry thoroughly. Never immerse the handle
in any liquid. Dry thoroughly.
5. Place the blades together and slide into the blade cover supplied.
6. Place the electric knife and accessories inside the box in which it was supplied in a dry place
out of reach of children. Never wrap the power cord around the knife or over-stress the cord
where it attaches to the handle.
11
If your products stops working, contact our call centre
at info@ayonz.com.
Do not attempt to open and repair the unit yourself.
6. SERVICE
7. SPECIFICATIONS
Power Supply 220-240V~ 50/60Hz 120W
Dimensions Main product size: 57x65x237mm
Main product with blade : 57x65x465mm
CUSTOMER HELPLINE:
info@ayonz.com
DISTRIBUTED BY:
Ayonz Pty Ltd
/
