9
EN
HOW TO START THE APPLIANCE
- Inserttheplugintotheoutlet.Turnthethermostatto“steam”position,Fig.C.
- Whenthewarninglight(5)goeson,theironisheatingup.
- Waitforabout4-5minutesuntilthewarninglightgoesoff.
- Now you may start to iron.
STEAM OUTFLOW
ThesteamoutowmaybeDISCONTINUOUSorCONTINUOUS.
- DISCONTINUOUSsteam:pressthepushbutton(4)Fig.Dbyapplyingmoreorlessstrengthaccordingtotheamountof
steam desired.
- CONTINUOUSsteam:turnthesteamcontrolknob(2)inaclockwisedirection(Fig.E)toobtainaconstantandcontinuous
steamoutow.Maximumintensityisobtainedwhentheknobisfullyturned.
- Maximumintensitycanalsobeobtainedintheautomaticsteamoutowmodebyfullypressingthesteampushbutton
(4).
- Never overturn the iron or tilt it forward or laterally while it is being used either in the discontinuous or continuous mode.
Attention!
Alwaysstopthesteamoutowbeforerestingtheironontheseparatestand(10).
NEVERUNSCREWTHESAFETYCAP(1)WHILETHEIRONISBEINGUSED.ALWAYSTURNOFFTHEIRONFIRST
BYTURNINGTHETHERMOSTATKNOBTO“MINIMUM”,REMOVETHEPLUGFROMTHEOUTLETANDFULLYPRESS
THEPUSHBUTTON(4)ASTOLETOUTALLTHERESIDUALSTEAM.
HOW TO FILL THE BOILER WHILE THE APPLIANCE IS BEING USED
Ifyouneedtolltheboilerduringtheironingsession,thefollowingoperationsshouldbecarriedout:
- Switchofftheironbyturningthethermostatknobto“MINIMUM”.
- Remove the plug from the outlet.
- Fullypressthepushbutton(4)astoletoutalltheresidualsteam.
- Unscrewtheboiler’ssafetycap(1).Thisoperationismadeeasierwiththecapremoversupplied(3),whichhelpsyouget
a better grip on the cap and protects against accidental burns.
- Pourasmallamountofwaterintotheboilerfor2or3timestoallowthesteamtocomeoutofthellingtube.
Afterwards,lltheboilerasusual.
N.B.: remember that the amount of water to be poured into the boiler while the iron is being used should never
exceed 210 cc as indicated on the measure. To be sure that the right quantity of water is poured into the boiler,
always drain the tank rst.
- Screw the safety cap on tightly.
- Insert the plug into the outlet.
- Steaming will recommence after a short time.
DRY IRONING
- First make sure there is no water in the boiler. Otherwise, stop the steaming by completely turning the steam control knob
(2)inananticlockwisedirection.
- Selecttheirontemperaturebestsuitedforthefabrictobeironedbymeansofthethermostatknob(Fig.C).Refertothe
table below.
SUGGESTIONS
Divide the articles to be ironed according to the types of material: wool with wool, cotton with cotton, etc.
Because the iron heats up much more quickly than it cools down, it is advisable to start with those fabrics which require
lower temperatures and move on to those which require progressively higher temperatures.
Ifthematerialismadeupofmorethanonetypeofbre,alwayssetthetemperaturetothebrewhichrequireslessheat.
Forexample,ifthematerialismadeupof70%syntheticsand30%cotton,setthetemperaturecontroltoposition(5-6)(see
table)withoutsteam,thatis,thetemperatureforsyntheticfabrics.
If you do not know the composition of the article to be ironed, choose a part of the article which will not be seen. Do a test
ironingonthisparttoestablishtheappropriatetemperature(alwaysstartwitharelativelylowtemperatureandworkupuntil
theidealtemperatureisreached).Pure(100%)woolarticlescanbeironedwiththeironsettooneofthesteampositions.
To avoid pure wool, silk and synthetic materials becoming shiny, it makes good sense to iron them on the reverse side. For