CRUICHFIELD 70-8117 User manual

Type
User manual

CRUICHFIELD 70-8117 is a receiver wiring adaptor designed to facilitate the installation of a new car stereo receiver in select Toyota vehicles. It allows you to match and connect the wires of your new receiver to the factory radio harness, ensuring proper functionality of the audio system. The adaptor provides color-coded wires for easy identification and includes instructions for connecting the wires based on the specific vehicle model. It also guides you in identifying and taping off any unused wires to prevent potential issues.

CRUICHFIELD 70-8117 is a receiver wiring adaptor designed to facilitate the installation of a new car stereo receiver in select Toyota vehicles. It allows you to match and connect the wires of your new receiver to the factory radio harness, ensuring proper functionality of the audio system. The adaptor provides color-coded wires for easy identification and includes instructions for connecting the wires based on the specific vehicle model. It also guides you in identifying and taping off any unused wires to prevent potential issues.

Receiver Wiring Adaptor
120 70-8117
Revision 06/14/21
STEP 1 -- MATCH & CONNECT WIRES
*120708117*
IMPORTANT
Before starting, compare items on your invoice with items
received. Thoroughly check packing materials. If an item
is missing, please call Crutchfield at 1-888-955-6000.
Copyright 2021 Crutchfield Corporation
Match wires below to the matching function of each wire on your receiver (refer to instructions supplied with receiver). The wire colors of your
new receiver may, or may not, match the wire colors of the adaptor. Match adaptor and receiver wires by function, disregarding color.
Some wire functions depend upon what vehicle the harness is being applied to. See the chart on the next page as a guide for your particular
vehicle before making any connections.
Individually tape off any unused wires.
Refer to the chart on page 3 for the amplifier location in your vehicle, and make final wiring connections following instructions on page 4.
A.
B.
C.
D.
White/Black - Left Front Speaker Negative
Violet/Black - Right Rear Speaker Negative
Yellow - 12 Volts Constant Power
Red - 12 Volts Switched Power
White - Left Front Speaker Positive
Blue - Power Antenna
Violet - Right Rear Speaker Positive
Green - Left Rear Speaker Positive
Gray - Right Front Speaker Positive
Gray/Black - Right Front Speaker Negative
Black - Chassis Ground
Green/Red - (see next page)
Dark Blue/Pink - (see next page)
Green/Black - Left Rear Speaker Negative
Green/Orange - (see next page)
Brown/White - (see next page)
Green/White - (see next page)
Yellow/Brown - (see next page)
White/Red - (see next page)
Brown/Blue - (see next page
Receiver Wiring Adaptor
120 70-8117
Green/Red
Dark Blue/Pink
White/Red
Brown/Blue
Green/Orange
Brown/White
Green/White
Yellow/Brown
Wire Color Vehicle/Function
4Runner, Sienna-
Rear Tweeters Negative
Matrix, Solara Convertible, Tacoma-
Sub Coil 2 Negative
Sequoia, Solara Coupe-
Left Front Tweeter Negative
Prius, Tundra-
Not Used (tape off)
4Runner, Prius, Sienna-
Center Speaker Negative
Matrix, Solara Convertible, Tacoma-
Sub Coil 1 Negative
Sequoia, Solara Coupe-
Right Front Tweeter Negative
Tundra-
Not Used (tape off)
4Runner-
Subwoofer Coil 1 Negative
Matrix, Prius, Tundra-
Left Front Door Woofer Negative
The White/Black wire is for the Left Front
Tweeter Negative
Sequoia, Solara, Tacoma-
Not Used (tape off)
Sienna-
Subwoofer Coil 2 Negative
4Runner-
Subwoofer Coil 2 Negative
Matrix, Prius, Tundra-
Right Front Door Woofer Negative
The Gray/Black wire is for the Right
Front Tweeter Negative
Sienna-
Subwoofer Coil 1 Negative
4Runner, Sienna-
Rear Tweeters Positive
Matrix, Solara Convertible, Tacoma-
Sub Coil 2 Positive
Sequoia, Solara Coupe-
Left Front Tweeter Positive
Prius, Tundra-
Not Used (tape off)
4Runner, Prius, Sienna-
Center Speaker Positive
Matrix, Solara Convertible, Tacoma-
Sub Coil 1 Positive
Sequoia, Solara Coupe-
Right Front Tweeter Positive
Tundra-
Not Used (tape off)
4Runner-
Subwoofer Coil 1 Positive
Matrix, Prius, Tundra-
Left Front Door Woofer Positive
The White wire is for the Left Front
Tweeter Positive
Sienna-
Subwoofer Coil 2 Positive
Sequoia, Solara, Tacoma-
Not Used (tape off)
4Runner-
Subwoofer Coil 2 Positive
Matrix, Prius, Tundra-
Right Front Door Woofer Positive
The Gray wire is for the Right Front
Tweeter Positive
Sienna-
Subwoofer Coil 1 Positive
Sequoia, Solara, Tacoma-
Not Used (tape off)
Page 2
Copyright 2021 Crutchfield Corporation
STEP 1 -- MATCH & CONNECT WIRES -- CONTINUED
Sequoia-
Not Used (tape off)
120 70-8117
Receiver Wiring Adaptor
Vehicle Applications and Amplifier Locations
2003-'06 Toyota 4Runner Passenger's rear side panel
2005-'06 Toyota Matrix Under front passenger's seat
2004-'05 Toyota Prius Under front passenger's seat
2005 Toyota Sequoia Below and behind radio
2004-'06 Toyota Sienna Behind glove box
2004 Toyota Camry Solara Behind glove box
2005-'07 Toyota Tacoma Behind rear seat on passenger's side
2004-'06 Toyota Tundra Behind rear seat on driver's side
Vehicle Amplifier Location
Copyright 2021 Crutchfield Corporation
Page 3
Receiver Wiring Adaptor Connections
120 70-8117
Page 4
STEP 2 -- CONTINUED
A. Strip wires back 1/2”.
B. Twist wires together and
insert in crimp cap.
C. Squeeze middle of cap
for tight connection.
Copyright 2021 Crutchfield Corporation
STEP 3 -- APPLICATION
When ready to install the receiver, plug
the Wiring Adaptor from the new receiver
or receiver assembly into the factory
radio harness(es) in the vehicle dash.
D. Complete crimp connections
for all necessary wires.
E. Be sure to wrap any wires from
the Wiring Adaptor that are
not necessary (wires with no
match from the new receiver)
with electrical tape.
STEP 2 -- CRIMP CONNECTIONS
Tools & Parts
Required4
Wire Stripper/Crimp Tool Crimp Caps
Unused Wire (tape over bare wires)
Receiver Wiring Adaptor
Generic Illustration
Generic Illustration
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

CRUICHFIELD 70-8117 User manual

Type
User manual

CRUICHFIELD 70-8117 is a receiver wiring adaptor designed to facilitate the installation of a new car stereo receiver in select Toyota vehicles. It allows you to match and connect the wires of your new receiver to the factory radio harness, ensuring proper functionality of the audio system. The adaptor provides color-coded wires for easy identification and includes instructions for connecting the wires based on the specific vehicle model. It also guides you in identifying and taping off any unused wires to prevent potential issues.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI