CAMDEN CI-3502 User manual

CI-3502
CAMDEN
Brand
CAMDEN
Model
CI-3502
Type
User manual

CAMDEN CI-3502 is a mortise cylinder key switch designed to control grilles or gates where high-security key access is required. It features double gang SS faceplate, 2 SPST N/O contacts for key switch, 1 SPST N/C contact for the emergency stop button, and a surface ABS box with a weather-resistant gasket.

CAMDEN CI-3502 is a mortise cylinder key switch designed to control grilles or gates where high-security key access is required. It features double gang SS faceplate, 2 SPST N/O contacts for key switch, 1 SPST N/C contact for the emergency stop button, and a surface ABS box with a weather-resistant gasket.

Page 1 of 3
CI-3502
Key Switches
INSTALLATION INSTRUCTIONS
Industrial Door and Gate Controls
Camden's mortise cylinder key switch is designed to
control grilles or gates where high security key access
is required. Includes double gang SS faceplate, (2) SPST
N/O contacts for key switch. (1) SPST N/C contact for red
emergency stop button. Surface ABS box and weather
resistant gasket. Mortise cylinder (1-1/8"), keyed different
& (2) keys included.
1. DESCRIPTION
2. SPECIFICATIONS
Contact Type STOP Button:
1 x N/C SPST
(Emergency STOP Pushbutton)
Key Switch:
2 x N/O SPST
Contact Rating 6A@125V AC
Enclosure NEMA 1 Surface Mount
Endurance 100,000 cycles
Mortise Cylinder 1 1/8", keyed different, (2) keys
Dimensions 5 1/8" x 5 1/8" x 2"
(130mm x 130mm x 51mm)
3. DIMENSIONS
51
8'' [130mm]
51
8'' [130mm]
35
16 '' [83.5mm]
415
16 '' [125.9mm]
2 '' [51mm]
https://manual-hub.com/
Page 2 of 3
CI-3502 Key Switches
INSTALLATION INSTRUCTIONS
4. INSTALLATION
1. The switches provided may be mounted in the left and
the right holes on the back of the faceplate. Thread the
octagonal nut (spacer ring) on to the bushing (stem) of the
switch before placing the switch in the hole.
2. Insert the switch up through the bottom of the desired
hole. Secure the switch in place by screwing the round
threaded washer onto the top of the switch.
3. Fit the mortise cylinder through the front of the face plate
being sure to align the grooves on the sides of the cylinder
with the corresponding “retainers” on the back of the face
plate.
4. Pushrmlyonthecylinder,untilitsnapsintoplace,lying
ushinthefrontofthefaceplate(aluminummodels
only).Notethatsomecylindersmayappearnottotin
the face plate. If the grooves on the side of the cylinder are
irregular and do not align with the retainers on the back
ofthefaceplate,useametalletoledowntheretainers
slightly.
Note: Do not le the retainers off completely as they
prevent the cylinder from spinning in the face plate.
5. Thread the brass cylinder lock ring onto the back of the
cylinder, and tighten in place.
6. Turn the key in the cylinder, and ensure the cam hits the top
of the switch squarely in the center. Adjust the switch in the
slotted hole until the cam hits in the center. It does not affect
operation of the cam if the cylinder rests against the switch,
so long as the switch is not fully depressed until activated by
a turn of the key. If the cam does not depress the switch, or
blocks the switch from resetting, raise or lower the octagon
nut located under the switch, as needed. Extra spacers are
provided and may be used as required.
7. Once the electrical connections are completed (see below),
attach the unit to the switch box, wall, or receptacle box using
the supplied tamperproof or stainless steel Phillips screws.
Foroutdooruse,placetherubberweatherproonggasket
behind the face plate prior to securing to the back box or wall.
Switch
Round threaded
washer
Face plate
Surface mount
backbox
Face plate
6-32 x 3/4
Screw
https://manual-hub.com/
Call: 1.877.226.3369 / 905.366.3377
Visit: www.camdencontrols.com
Opening New Doors to
Innovation, Quality and Support!
Page 3 of 3
CI-3502 Key Switches
INSTALLATION INSTRUCTIONS
File: CI-3502 Designer
Installation Instructions.indd R2
Revision:15/05/2018
Part No.: 40-82B073
5. WIRING
Momentary: SPST switches have normally open (N.O.) 6 amps @ 12/24/30 VAC.
6. OPTIONAL LED WIRING
KeySwitchesmaybeorderedwithoptionalLED’s.ThisdrawingsshowthevariouswiringcongurationsoftheLED’s.
RED, GREEN
or AMBER LED
24 VDC
RED
1.5k ohms
BLACK
RED, GREEN
or AMBER LED
24 VDC
NOTE: These LED’s are designed for DC Voltage only
RED
560 ohms
BLACK
RED
GREEN
RED
GREEN BLACK
SPDT
Switch
Bi-Color
LED
12 VDC
560 ohms
Resistor GREEN
RED RED
GREEN BLACK
SPDT
Switch
Bi-Color
LED
24 VDC
1.5 k ohms
Resistor
1
2
N/C Contacts
N/O
Contacts
N/O
Contacts
https://manual-hub.com/
  • Page 1 1
  • Page 2 2
  • Page 3 3

CAMDEN CI-3502 User manual

CI-3502
CAMDEN
Brand
CAMDEN
Model
CI-3502
Type
User manual

CAMDEN CI-3502 is a mortise cylinder key switch designed to control grilles or gates where high-security key access is required. It features double gang SS faceplate, 2 SPST N/O contacts for key switch, 1 SPST N/C contact for the emergency stop button, and a surface ABS box with a weather-resistant gasket.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents