Follett H50R5A/W Installation guide

Brand: Follett

Model: H50R5A/W

Category: Ice cube makers

Type: Installation guide

This manual is also suitable for

25 and 50 Series

Ice and Water Dispenser

Installation Manual

206649

10/00

C25T5A/W C50T5A/W

Cool Ideas For Ice Management

801 Church Lane • P.O. Box D, Easton, PA 18044

Toll-free (800) 523-9361 • (888) 2-FOLLETT

(610) 252-7301 • FAX (610) 250-0696 • www.follettice.com

H25T5A/W H50T5A/W

C25R5A/W C50R5A/W

H25R5A/W H50R5A/W F255A/W F505A/W

ICDI220

Attention installer

Follett ice dispensers enjoy a well-deserved reputation for excellent performance, long-term reliability, and outstanding

after-the-sale support. To ensure that this dispenser delivers that same degree of service, we ask that you review this

manual before beginning to install the dispenser. This manual is designed to help you achieve a perfect installation.

Should you have any questions or require technical help at any time, please call our technical service group toll-free at

(800) 523-9361 or (888) 2-FOLLETT, or at (610) 252-7301.

Before you begin

After uncrating and removing all packing material, inspect the equipment for concealed shipping damage. If damage is

found, notify your shipper immediately and contact Follett Corporation for help in filing a claim, if necessary.

Caution: Do

NOT tilt any freestanding model or icemaker unit further than 30° off vertical during uncrating or installation.

Check your paperwork to determine which model you have. Follett model numbers are designed to provide information

about the type and capacity of Follett ice dispensing equipment. Following is an explanation of model numbers:

Electrical specifications

Models with remote icemakers require separate circuit and disconnect for icemaker and dispenser

Icemaker Max. Fuse Dispenser Max. Fuse

Basic electrical 115/60/1 11.0 amps 20 amps 2.0 amps 15 amps

Alternate electrical 230/50/1 6.0 amps 15 amps .8 amps 15 amps

Freestanding models and models with integral icemakers require only one circuit and disconnect for unit

Total System Max. Fuse

Basic electrical 115/60/1 13.0 amps 20 amps

Alternate electrical 230/50/1 6.8 amps 15 amps

All models must be hard-wired. Equipment ground required. Electric disconnect(s) required within 10 ft. (3 m) of dispenser

for all freestanding models and all 25/50 Series dispensers with integral 5A/W icemakers; one disconnect each for

dispenser and icemaker for 25/50 Series dispensers with R5A/W remote icemaker.

C50T5A

Condenser type – A = air cooled, W = water cooled

Icemaker capacity and refrigerant – 5 = 400 lbs.(181 kg) /day, R22 refrigerant

Icemaker location – R = remote icemaker; T = integral icemaker in top of cabinet.

Note: No letter is used to indicate icemaker located in base of freestanding units.

Approximate storage capacity in lbs.

Dispenser configuration – C = countertop, H = wallhung, F = freestanding

Important cautions

• Dispenser bin area contains mechanical, moving parts. Keep hands and arms clear of this area at all

times. If access to this area is required, power to unit must be disconnected first.

• Follett recommends a QC4-FL4S water filter system (order #AFSYSTMFL4S) be installed in icemaker inlet

water line.

• Ice is slippery. Maintain counters and floors around dispenser in a clean and ice-free condition.

• Ice is food. Follow recommended cleaning instructions to maintain cleanliness of delivered ice.

• Countertop dispensers which sit on legs (not bolted to counter) can be inadvertently moved. Care should be taken

when operating and cleaning to avoid accidents.

ICDI220

Ambient specifications

Air Temp 100° F/38°C Max. 50°F/10°C Min. (Best performance below 80˚F/27˚C)

Water Temp 90°F/32°C Max. 40°F/4°C Min. (Best performance below 70˚F/21˚C)

Water Pressure 70 P.S.I. Max. 10 P.S.I. Min.

Plumbing

C25/50 with H25/50 with C25/50 with H25/50 with F25/50

remote icemaker remote icemaker integral icemaker integral icemaker

Dispenser drain 3/4" FPT 3/4" ID tubing 3/4" FPT 3/4" ID tubing 3/4" FPT

Icemaker drain 1/2" MPT 1/2 MPT ––3/8" FPT

Dispenser water inlet 3/8" FPT 3/8" FPT 3/8" FPT 3/8" FPT 3/8" FPT

Remote IM water inlet 1/4" FPT 1/4" FPT –––

Cond. inlet – w/c only 3/8" FPT 3/8" FPT 1/2" FPT 1/2" FPT 3/8" FPT

Cond. drain – w/c only 1/2" FPT 1/2" FPT 1/2" FPT 1/2" FPT 1/2" FPT

Note: Water shut-off recommended within 10 feet (3 m) of dispenser.

Drain to be hard piped and insulated, and maintain at least 1/4" per foot (6 mm per 30.4 cm run) of slope.

Field wiring diagrams

Freestanding dispensers, countertop and wallhung dispensers with integral icemakers

Countertop and wallhung dispensers with remote icemakers

Electric Power Source

Standard electrical - 115V, 1 Ph, 60 Hz,

max. fuse size 20 amps

Alternate electrical - 230V, 1 Ph, 50 Hz,

max. fuse size 15 amps

GND

GRN

GND

GRN

LEGEND

WIRENUT

EQUIPMENT

GROUND

B - BLACK

W - WHITE

R - RED

GRN - GREEN

DISPENSER

JUNCTION BOX

FIELD WIRING DIAGRAM IS

INTENDED TO AID ELECTRICIAN

OR TECHNICIAN IN UNDERSTANDING

HOW EQUIPMENT WORKS. ALL FIELD

WIRING MUST BE INSTALLED IN

ACCORDANCE WITH NEC AND LOCAL

ELECTRICAL CODES.

IMPORTANT

FUSED

DISCONNECT

Electric Power Source

Standard electric - 115V, 60 Hz, 1 Ph,

Max. fuse size per circuit - 15 amps

Alternate electric - 230V, 50 Hz, 1 Ph

Max. fuse size per circuit - 15 amps

GND

GRN

GND

GRN

LOWER ICEMAKER

JUNCTION BOX

(BIN SIGNAL)

FUSED

DISCONNECT

LEGEND

WIRENUT

EQUIPMENT

GROUND

B - BLACK

W - WHITE

R - RED

GRN - GREEN

DISPENSER

JUNCTION BOX

FIELD WIRING DIAGRAM IS INTENDED TO AID ELECTRICIAN

OR TECHNICIAN IN UNDERSTANDING HOW EQUIPMENT WORKS.

ALL FIELD WIRING MUST BE INSTALLED IN ACCORDANCE WITH

NEC AND LOCAL ELECTRICAL CODES.

IMPORTANT

GND

GRN

GND

GRN

UPPER ICEMAKER

JUNCTION BOX

(POWER)

FUSED

DISCONNECT

Electric Power Source

ICDI220

Installation procedures

Installing freestanding dispensers

1. Carefully tip dispenser back to

expose underside and block up in

place.

2. Remove legs from shipping box

(taped to drain pan of dispenser) and

screw into dispenser bottom, taking

care to seat legs securely against

underside of dispenser.

3. Position unit in desired location and

adjust bullets on legs to level in both

directions.

4. Remove front cover of base section

and unblock shipping tie-down

securing icemaker to dispenser base.

5. Make final connections.

18.125"

46 cm

10.5" (26.7 cm)

9.75"

24.8 cm

15"

38.1 cm

1/2" FPT

condenser

drain (water

cooled only)

3/8" FPT

icemaker drain

(water cooled only)

3/8" FPT

condenser inlet

(water cooled only)

5.5" (14 cm)

3.5"

8.9 cm

electrical

connection

box

electrical entrance

9.25"

23.5 cm

3/4" FPT

dispenser drain

3/8" FPT

icemaker drain

(air cooled only)

28.5"

72.4 cm

3/8" FPT

water inlet

10"

25.4 cm

38"

96.5 cm

access

panel

34"

86.4 cm

Rear connections — Freestanding models

Before you begin

• All dispensers must be installed level in both directions to ensure proper operation.

• Required service and ventilation clearances:

• Models with integral icemakers (in top of cabinet) — 6" (15.2 cm) on right side of dispenser and at top.

• Models with remote icemakers — 12" (30.5 cm) at top.

• Freestanding models — 12" (30.5 cm) at top and 4" (10.2 cm) at back.

• All countertop and wallhung dispensers provide the option of taking utilities out the bottom or back of the

dispenser. See counter cut-out drawings for bottom exiting utilities on units with and without drain pans. For

installations where utilities will exit through back of dispenser, refer to back view drawings.

• Wallhung models are designed for use above sinks or custom drain pans and are not normally equipped

with integral drain pans.

(Center of sink should be 19.5" (49.5 cm) from back wall.) Connection of utilities through

the back for wallhung units is the same as shown in drawings for countertop models except that the 3.25" (8.3 cm)

high drain pan is absent.

Note: Electrical connection box can

also be accessed through front of

dispenser by removing front cover,

black plastic chute cover and

stainless splash panel.

Do NOT tilt unit further

than 30° off vertical.

Shaded

areas

indicate

internal

connections

ICDI220

Installing countertop dispensers without legs

1. For units where utilities will exit through back of dispenser, remove cap from drain fitting on back of unit and install

cap on fitting tee inside dispenser.

2. Position dispenser in desired

location, mark dispenser outline on

counter, and remove dispenser.

3. Regardless of how utilities will be

connected, drill four (4) holes in

counter to anchor dispenser to

counter (see figures above).

4. For units with utilities exiting

through counter, make appropriate

counter cut-out as shown above.

5. Apply a thick bead - approximately

1/4" (6 mm) diameter - of NSF

listed silicone sealant (Dow-

Corning RTV-732 or equivalent)

1/4" (6 mm) inside marked outline

of dispenser.

6. Carefully lower dispenser on counter in

proper position and secure to counter with four (4) bolts.

7. Smooth excess sealant around outside of dispenser.

8. If dispenser has remote icemaker and unit is equipped with water station accessory, make water connection for water

station inside dispenser as indicated.

9. Make final connections. Proceed with instructions for installing remote or integral icemakers as appropriate.

23.0625"

586 mm

. 375"

10 mm

10.5"

267 mm

.5" (13 mm) to

cutout

16.75"

425 mm

21"

533 mm

2.125"

54 mm

.375"

diameter -

4 places

9" x 14"

229 mm x 356 mm

cutout

1.5626"

40 mm

10.5"

267 mm

.5" (13 mm) to

cutout

.375"

diameter -

4 places

9" x 14"

229 mm x 356 mm

cutout

20.125"

(511 mm)

21" (533 mm)

12.5"

318 mm

19"

483 mm

6" min.

152 mm

2.5"

(64 mm)

Counter cut-out for units with drain pan

Counter cut-out for units without drain pan

electrical

connection

6.125"

15.6 cm

5.156"

13.1 cm

10.5"

26.7 cm

14.75"

37.5 cm

3/4"

FPT drain

plumbing

connection

access

panel

junction box

Rear connections – Countertop

models with integral icemakers

electrical

connections

6.125"

15.6 cm

5.156"

13.1 cm

ice transport

tube

10.5"

26.7 cm

14.75"

37.5 cm

3/4"

1.9 cm

FPT drain

plumbing

connection

access

panel

junction box

Rear connections – Countertop

models with remote icemakers

Counter cut-outs

Note: Electrical connection box can also be accessed through front of dispenser by removing front cover, black plastic

chute cover and stainless splash panel.

Shaded

areas

indicate

internal

connections

ICDI220

Installing countertop dispensers with legs accessory

1. For units where utilities will exit through back of dispenser, loosen rear-most clamp connecting PVC drain line to

flexible tubing, rotate line 180˚ so unused opening of tee fitting faces up, tighten clamp and cap unused tee opening

with plastic cap provided.

2. Fasten two (2) narrow U-shaped channels to underside of dispenser with four (4) 1/4-20 screws supplied. Channels

should be installed with flanges facing up into bottom of dispenser.

3. Use supplied six (6) 8-32 sheet metal screws to attach larger U-shaped metal filler piece to underside of dispenser

between installed flanges. Knock-out holes in this filler should be toward rear of dispenser.

4. Screw legs to channels and tighten securely.

5. Make final connections.

6. If unit is equipped with water station accessory, make water connection for water station inside dispenser as

indicated.

7. Proceed with instructions for installing remote icemaker.

Installing countertop dispensers with base stand accessory

1. Install supplied flanged legs, being sure to seat securely against bottom of base stand.

2. Position base stand in desired location.

3. Adjust legs to level base stand from left to right and front to back.

4. Mark floor for holes that will be drilled to anchor unit.

Steps 5 through 14 required only to reverse door orientation.

5. Lift door off hinge pins.

6. Relocate door hinges by using alternate door holes provided.

7. Remove hinges from base stand.

8. Remove plug from one end of hinges and reinstall plug in opposite end of hinges.

9. Reinstall hinges in threaded holes on opposite side of base stand, countersunk side out.

10. Reposition door on hinges.

11. Remove screws from each of two (2) striker plates.

12. Reinstall striker plates on opposite side of base stand, but do not tighten screws.

13. Close door.

14. Reach inside base from top to align striker plates with magnets and tighten screws to secure.

All units

15. Slide base stand away from its location and drill holes for 1/4" anchoring bolts appropriate to floor material

(anchoring bolts not supplied.)

16. Return base stand to its intended location and anchor base stand through flanged legs into floor with 1/4" bolts.

17. Position dispenser on top of base stand and install supplied spacers between top of base stand and under cage

nuts on bottom of dispenser.

18. Using supplied 1/4" screws, secure dispenser to base stand through top of base stand into cage nuts on bottom of

dispenser.

19. Connect utilities.

20. Refer to installation instructions provided with dispenser and proceed with installation of icemaker.

Note: Electrical connection box can also be accessed through front of dispenser by removing front cover,

black plastic chute cover and stainless splash panel.

Only models with remote icemakers can be installed on legs. Legs cannot be used with

models equipped with integral icemakers (icemaker in top of cabinet).

To avoid possible tipping and resulting injuries, securely bolt base stand to floor through

flanged legs provided. 1.5" (3.8 mm) clearance required on hinge side of cabinet to allow

door to fully open.

ICDI220

Installing 25 and 50 Series wallhung dispensers

1. For all 25 and 50 Series wallhung dispensers, install supplied wall bracket

with six (6) 3/8" dia. fasteners as shown in diagrams below. (Note

that three holes are available at each fastening site to allow capture

of studs/support within wall.)

Steps 2 - 3 are required for Models H25T5A/W and H50T5A/W only.

2. For models with integral icemakers only (models H25T5A/W and

H50T5A/W), use straight edge to position filler strip flush with top

edge of wall bracket.

3. Fasten filler strip to wall as shown in drawings on page 7.

4. For all models, cut utility hole in wall using wall bracket as template.

5. Lift dispenser onto wall bracket, positioning unit such that hook on

back of dispenser is captured by wall bracket support angle.

6. Install four (4) 1/4-20 screws through bottom of wall bracket into

bottom of dispenser to secure dispenser.

7. To gain access for final connections, remove access plate in bottom

of wall bracket.

8. If dispenser has remote icemaker and unit is equipped with water

station accessory, make water connection for water station inside

dispenser as indicated.

9. Proceed with instructions for installing remote or topmounted

icemaker as appropriate.

19 3/8"

Min. distance to

front of sink = 23"

2.75"

7 cm

CL utility

entrance

H25T5A/W

30.625"

77.8 cm

H50T5A/W

34.625"

88 cm

24.75

17"

43.2 cm

49.2 cm

(58.4 cm)

62.9 cm

H25T5A/W

44.375"

112.71 cm

H50T5A/W

48.375"

122.9 cm

Support angle and

hook detail

Side view and angle detail for wallhung units

with integral icemakers (in top of cabinet)

(Wallhung units with remote icemakers will not

require installation of a filler strip above support

angle and hook.)

Wall stud

16"

406 mm

3.40625" (87 mm)

11.4375"

291 mm

4.59375"

125 mm

utility cutout

3.5"

89 mm

1.28125"

33 mm

25.625"

651 mm

9.5"

241 mm

Wall Bracket

support angle

3/8"

fasteners (6 sites)

9.5"

241 mm

Wall stud

16"

406 mm

.40625" (87 mm)

11.4375"

291 mm

4.59375"

125 mm

utility cutout

3.5"

89 mm

1.28125"

33 mm

29.625"

752 mm

11.5"

292 mm

Wall Bracket

support angle

3/8"

fasteners (6 sites)

11.5"

292 mm

H25R5A/W mounting dimensions H50R5A/W mounting dimensions

Note: Electrical connection box can also be accessed through

front of dispenser by removing front cover, black plastic chute

cover and stainless splash panel.

Caution: Do NOT rest dispenser weight on

bottom front edge of wall bracket.

ICDI220

Installing remote icemaker (Models C25R5A/W, C50R5A/W, H25R5A/W, H50R5A/W)

When 10 feet (3 m) or less of ice transport tube is required to carry ice from evaporator port to dispenser, the unit will be

shipped with one end of tube already installed in mounting bracket of dispenser. For runs that exceed 10 feet (3 m) the

tubing is not mounted and requires a different installation procedure. Refer to appropriate section below for your specific

installation.

Units shipped with standard 10 feet (3 m) of ice transport tube

1. Position icemaker in desired location.

2. Refer to R5A/W Installation Manual (Form #206428) packed with icemaker for installation instructions, restrictions on

ice transport tube run and ventilation requirements for remote icemakers.

Units shipped with more than 10 feet (3 m) of ice transport tube

1. Remove top and rear access panel from dispenser.

2. Run end of ice transport tube with 3/16" (1.9 mm) hole through right hand knockout in back of dispenser or through

counter into bottom of dispenser, being careful to avoid any

bends with less than a 6" (15.2 cm) radius.

3. Insert tube in internal chase in rear inside corner of dispenser

(right side as you face rear of dispenser) and push up into

storage area.

4. Push 3/16" (5 mm) hole near end of tube into engaging pin on

ice tube bracket (see drawing at right).

5. Install supplied insulation to run of transport tube required for

your site, leaving approximately 2" (5.1 cm) of tube exposed

at free end.

6. Check that insulated tube runs continuously uphill to

dispenser with no dips.

20.625"

524 mm

16"

406 mm

1.0625"

27 mm

2.3125"

59 mm

3.40625" (87 mm)

11.4375"

291 mm

4.59375"

125 mm

utility cutout

3.5"

89 mm

1.28125"

33 mm

25.625"

651 mm

9.5"

241 mm

44.25"

1124 mm

Wall Bracket

support angle

3/8" (10 mm)

fasteners (6 sites)

wall stud

filler strip

9.5"

241 mm

20.625"

524 mm

16"

406 mm

1.0625"

27 mm

2.3125"

59 mm

3.40625" (87 mm)

11.4375"

291 mm

4.59375"

125 mm

utility cutout

3.5"

89 mm

1.28125"

33 mm

29.625"

752 mm

11.5"

292 mm

48.25"

1226 mm

Wall Bracket

support angle

3/8" (10 mm)

fasteners (6 sites)

wall stud

filler strip

11.5"

292 mm

H50T5A/W mounting dimensionsH25T5A/W mounting dimensions

2.5 cm

Capillary

tube

Ice

tube

Engaging pin

Ice tube

bracket

Back wall

3/16"

1.9 mm

hole in

ice tube

See R5A/W Installation Manual (Form #206428) for critical installation instructions for

remote icemakers. Failure to comply with these instructions will result in poor

performance and void warranty.

ICDI220

7. Place free end of tube in cup of hot water to soften, slip supplied hose clamp onto tube and push tube onto exit port

of evaporator. DO NOT TWIST HOSE WHEN SECURING TO EVAPORATOR.

8. Fasten tube on port with hose clamp, being sure that clamp is positioned on evaporator side of flange.

9. Tighten clamp.

Installing integral icemaker (in top of dispenser cabinet)

1. Remove two screws located under front access panel of dispenser.

2. Pull bottom of access panel forward and lift off.

3. Remove icemaker top and louvered panel from right side of icemaker.

4. Remove hold down bracket from front of icemaker base.

5. Lift icemaker onto dispenser top and slide into position, compressor end first,

locating icemaker flush with front of dispenser.

6. Reinstall hold down bracket on front of icemaker.

7. Remove ice transport tube from evaporator nozzle.

8. Insert loose end of ice transport tube into bracket and pull up to seat (see drawing).

9. Push ice transport tube onto compression nozzle and secure with hose clamp.

10. Push transport tube behind clip on float bracket to prevent contact with fan blades.

11. Place end of drain hose in hot water to soften and connect to elbow attached

to evaporator drain line.

12. Connect electric twist locks.

13. Connect plastic water line to fitting at float tank.

14. Reinstall side panel and top on icemaker.

15. Reinstall front access panel on dispenser.

Cleaning and sanitizing before use

Using solutions below, clean and sanitize storage area of dispenser before starting up unit.

Solution A: Prepare cleaning solution (200 ppm of available chlorine content) of Ecolab Mikro-chlor Cleaner

or equal chlorinated detergent. Cleaning solution temperature must be at 75˚F – 125˚F (24˚C –

52˚C).

Solution B: Prepare sanitizing solution (50 ppm of available chlorine content) of Ecolab Mikro-chlor Cleaner

or equal chlorinated detergent. Sanitizing solution temperature must be at 75˚F – 125˚F (24˚C –

52˚C).

1. Working inside storage area, remove center thumbscrew from dispense wheel, tilt wheel up toward back to clear

baffle and lift wheel out.

2. Wipe all bin and wheel surfaces with Solution A .

3 Rinse thoroughly with clear, potable water.

4. Wipe with Solution B to sanitize.

5. Reinstall dispense wheel.

Start-up

1. Clean and sanitize ice storage area of dispenser in accordance with instructions above before making ice.

2. Turn on icemaker and begin to make ice (icemaker should start within 45 seconds with power and bin signal

supplied).

3. After approximately 30 minutes, test dispenser for proper dispensing.

Ice tube

bracket

Plate

Gasket

Ice

deflector

Icemaker

base

Cap tube

bracket

Mounting pin

Dispensers with integral icemakers cannot be mounted on legs. They must be bolted to

counter. Use gloves or a cloth when lifting icemaker to protect hands from sheet metal

edges.

Warning: Disconnect power before cleaning dispenser.

ICDI220

206649

10/00

Cool Ideas For Ice Management

801 Church Lane • P.O. Box D, Easton, PA 18044

Toll-free (800) 523-9361 • (888) 2-FOLLETT

(610) 252-7301 • FAX (610) 250-0696 • www.follettice.com

ICDI220

Follett H50R5A/W Installation guide

Brand: Follett

Model: H50R5A/W

Category: Ice cube makers

Type: Installation guide

This manual is also suitable for

Download PDF

report

Follett H50R5A/W Installation guide

This manual is also suitable for

Follett H50R5A/W Installation guide

Related papers

Other documents