Follett Horizon H_E700AHT Installation Instructions Manual

Follett
Brand
Follett
Model
Horizon H_E700AHT
Type
Installation Instructions Manual

This manual is also suitable for

00978775R00
Order parts online
www.follettice.com
Horizon
™
Icemaker Installation Instructions
for Harmony
™
Top-mount Applications
H_C700AHT, H_C700WHT,
H_D700AHT, H_D700WHT
H_E700AHT, H_E700WHT
(See model number con gurator on page 2 for details.)
self-contained
Horizon top-mount icemakers
t most countertop dispensers manufactured by
Cornelius • Lancer • SerVend
801 Church Lane • Easton, PA 18040, USA
Toll free (877) 612-5086 • +1 (610) 252-7301
www.follettice.com
2
self-contained HARMONY • TOP-MOUNT
Horizon Series Ice Machine Model Number Configurations
A Air-cooled, self-contained
W Water-cooled, self-contained
A V SC 700HC
C 208-230/60/1
(self-contained only)
D 115/60/1 self-contained
E 230/50/1
(self-contained only)
Icemaker Voltage Series Condenser
V Vision™
H Harmony™
B Ice storage
bin
J Drop-in
700 up to
750 lbs
(340kg)
S RIDE™
(RIDE remote
ice delivery
equipment)
T Top-mount
Application Configuration
HC Horizon
Chewblet
®
HM Horizon
Micro Chewblet
®
HARMONY • TOP-MOUNT self-contained
3
Front cover
8
Internal connection
7
Ice transport tube
5
External connection
6
Louvered docking assembly
4
Dispenser preparation
3
Site preparation
2
Unpack
1
Read and complete the following 8 installation steps
4
self-contained HARMONY • TOP-MOUNT
Carefully unpack and inspect the contents of your Follett icemaker.
1
Unpack
7/16"
7/16"



Unpack icemaker
1. 1
HARMONY • TOP-MOUNT self-contained
5
Prepare the installation site.
2
1/4"
1'
5-15
NEMA
H_C700A/W
H_D700A/W
6-15
NEMA
Site preparation
2.1
Provide drainage, water supply and electrical power to within 6 feet (2m) of
icemaker in accordance with local and national codes. Outdoor installation is
not recommended and will void warranty.
Electrical
➊
• H_C700(A/W)HT 208-230/60/1-15 amp breaker • H_D700(A/W)HT 115/60/1-15 amp breaker
(H_C700A/W Requires a 15 amp dedicated circuit) (H_D700A/W Requires a 15 amp dedicated circuit)
• H_E700(A/W)HT 230/50/1-15 amp
‡
breaker
(H_E700A/W Requires 15 amp circuit 1.50 mm
2
wire)
‡ Plug must be provided by end user & must conform to standard EN 60 335-2-24 of the end destination.
Potable water supply
➋
• 10-70 psi (69-483kpa)
• 45 to 90 F (7 to 32 C)
• Water supply must be treated by a scale-inhibiting  lter (item# 00130286)
Condenser water supply for water-cooled systems
➌
• 10 psi min.; 150 psi max. (69kpa min.; 1034kpa max.)
• 20 to 90 F (-7 to 32C)
• 1.5 gallons per minute (5.68 liters per minute)
Drain
➍
• The drain line from the ice machine must be vented and have at least 1/4” per foot
(6,4mm/0,3m) pitch
115V ±5%
208V -5% to 230V +5%
Installation site requirements
2.1
6
self-contained HARMONY • TOP-MOUNT
Prepare the dispenser.
3
Dispenser preparation
➊
➊
All models
• Remove protective tape from gaskets
➊
Top preparation – ALL
3.1
➋
➊
➊
➌
• Apply gaskets
➊
.
• Install coupling
➋
through bottom of
dispenser top and secure with locking nut
➌
Top preparation – ALL
3.2
Note: The instructions below only apply to 22" & 30" wide dispensers.
44" wide dispenser instructions may be found with the top kit.
➋
➊
Cornelius models only
• Remove protective tape
➊
• Apply gasket
➋
Top preparation – CORNELIUS
3.4
➋
➊
• Screw 4" (102mm) extension
➊
into
bottom of shuttle actuator
➋
Top preparation – ALL
3.3
HARMONY • TOP-MOUNT self-contained
7
➊
➋
➋
ON
OFF
Lancer models only
• Remove protective tape
➊
• Apply gaskets
➋
Top preparation – LANCER
3.5
Cornelius models ED, DB, DF, IDC
and Flavor Fusion
Adjust the agitation timer located on the
Cornelius PC board to 1 second on, 1 hour
off. Note: see Cornelius manual for more
information.
Agitation adjust. – CORNELIUS
3.6
PRESS IN ON
THIS SIDE TO
TURN SWITCH
ON.
SWITCH
ON
SWITCH
OFF
PRESS IN ON
THIS SIDE TO
TURN SWITCH
OFF.
ROCKER
SWITCHES
(VIEW LOOKING
DOWN)
SIDE VIEW
SIDE VIEW
1
2
3
4
5
6
7
8
OFF
SWITCH
NUMBER
AGITATION FREQUENCY
NO A
GIT
ATION
10 MINUTES
20 MINUTES
30 MINUTES
40 MINUTES
50 MINUTES
60 MINUTES
70 MINUTES
80 MINUTES
90 MINUTES
100 MINUTES
110 MINUTES
120 MINUTES
130 MINUTES
140 MINUTES
150 MINUTES
5
6
7
8
O
O
O
O
O
O
O
X
O
O
X
O
O
O
X
X
O
X
O
O
O
X
O
X
O
X
X
O
O
X
X
X
X
O
O
O
X
O
O
X
X
O
X
O
X
O
X
X
X
X
O
O
X
X
O
X
X
X
X
O
X
X
X
X
SWITCH
NUMBER
AGITATION TIME
1 SECOND
2 SECONDS
3 SECONDS
4 SECONDS
3
4
O
O
O
X
X
O
X
X
X = ON
O = OFF
Lancer 4500 series only
Adjust the agitation time to 1 second, and the agitation frequency to 150 minutes. See Lancer
manual for more information.
Agitation adjustments – LANCER 4500 SERIES
3.7
8
self-contained HARMONY • TOP-MOUNT
Major/Minor
FS-16 Setup
Config Bonus Key
Soda/Plain Water
Config Dispense Only
PC Mode
PC Time
Ice Stir Off
Ice Stir On
Sold Out
Carb Sensors
Ice Bin Sensors
Valve Code Version
Number Of Valves
Reset Defaults No Yes
Reload Defaults?
1 2 3 4
12 0.104 0.104
1000
Ice Bin Optic
Upper Lower
Sold Out #1
Selection Sold Out
05000
On Time (MSEC)
Off On
Set PC Mode Menu
V:1 B1 DLY1
Dispense Delay
V:2 1:S 2:W 3:S 4:W
V:1 T:F M:S B:W
Bonus Key Setup
Brands Per Side
V:1 L:2 R:1
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
Soda/Plain Water
OFF Time (MIN)
00150
On Time (MSEC)
01000
1000 500
34 0.104 0.104
On On On On
V:1 B:1
Sold Out #1
Off
Sold Out #1
Ver. 0.200
Lancer FS-16
Sub-CatagoryMain Menu
Initialization Screen
2nd Sub-Catagory
(Boot Up Only)
Cancel
Enter
Scrolls through Main Menu
Press "Enter" to enter sub-catagory
Moves curser to right or left
Changes value (number/letter)
Press "Enter" to enter save changes
Press "Cancel" to exit menu
➊
Lancer FS series only
• Hold down “cancel” and “left button” to get to hidden menu
➊
• Type in code 6655
• Type in 150 minutes of off time and 1000 milliseconds (1 second of time) as the preferred
setting
Note: See Lancer manual for more information
Agitation adjustments – LANCER FS SERIES
3.8
Agitation adjustments – SERVEND
3.9
SerVend models only
No agitation adjustment required.
HARMONY • TOP-MOUNT self-contained
9
10-32 nut
flat washer
ice chute
gasket
apply food-grade
silicone sealant
to this surface
to seal to bin gate
mounting plate
ice diverter
(supplied)
mounting
gate
plate
storage bin
plate
gate
restrictor
gate opening
bin through
into storage
flange extends
➋
➊
Cornelius ED, DF and DB series only
These dispensers require the installation of an ice diverter at the dispenser opening.
• Disassemble chute assembly
• Discard factory restrictor plate
➊
• Replace with alternate diverter plate,
➋
(supplied)
Dispenser diverter plate installation – CORNELIUS ED, DF and DB SERIES
3.10
10
self-contained HARMONY • TOP-MOUNT
➊
➋
adjust restrictor
plate to fully
open position
Cornelius IDC and Flavor Fusion
These dispensers require the adjustment of the ice restrictor plate.
• Loosen four nuts on ice chute assembly
➊
• Adjust restrictor plate to fully open position
➋
• Replace four nuts and tight to 50 in lbs (max.)
Restrictor plate adjustment – CORNELIUS IDC and FLAVOR FUSION
3.11
HARMONY • TOP-MOUNT self-contained
11
Install the louvered docking assembly.
Louvered docking assembly
4
sealant
• Mount louvered docking assembly using
two screws provided.
• Seal perimeter of docking station to
mounting surface.
Louvered docking assembly
4.1
WARNING
• Docking station must be secured in accordance with these instructions to ensure icemaker stability.
• Ventilation openings in the louvered docking station should be clear of obstruction. Failure to do so
could result in damage to equipment.
12
self-contained HARMONY • TOP-MOUNT
Hot Water
160 F (71 C)
Ice transport tube
Install the ice transport tube.
5
5.1
• Cut transport tube to 26” (66 cm) length
• Install supplied ice transport tube insulation
• Heat end of transport tube in cup of 160 F (71 C) hot water to soften and spread with pliers
➊
before making connection to ease assembly
• Connect ice transport tube to coupling on louvered docking station
➋
• Connect ice transport tube to shuttle actuator
➌
HARMONY • TOP-MOUNT self-contained
13
Connect utilities to louvered docking assembly.
6
External connections
➊
➌
➋
➍
➋
➊
• Remove access panel if necessary
• Install drain line
➊
.
The rigid drain line from the icemaker
must be vented and have at least 1/4" per
foot (6,4mm/0,3m) pitch.
• Install icemaker potable water supply
➋
• Replace access panel
Air-cooled icemakers only
• Remove access panel if necessary
• Install drain line
➊.
The rigid drain line from the icemaker
must be vented and have at least 1/4" per
foot (6,4mm/0,3m) pitch.
• Connect cooling water supply
➋
and
return
➌
• Install ice machine potable water
supply
➍
• Replace access panel
Water-cooled icemakers only
6.1
6.2
14
self-contained HARMONY • TOP-MOUNT
Connect louvered docking assembly to icemaker.
7
Internal connections
• Remove twist tie
• Carefully pass plug thru opening and plug
into wall outlet
Power cord
7. 3
• Slide icemaker into louvered docking
assembly
➊
• Insert ice transport tube all the way into
coupling and tighten nut  rmly
➋
Ice transport tube
7. 1
• Insert potable water line into valve
➊
Potable water and drain lines
7. 2
Air-cooled icemakers – follow steps 7.1 through 7.4.
• Position plate into opening and secure
with supplied screw
Power cord
7. 4
CAUTION
• Plug must be accessible after  nal installation.
➊
➋
HARMONY • TOP-MOUNT self-contained
15
• Insert potable water line into valve
➊
Potable water and drain lines
7. 7
• Install icemaker cooling water lines to
louvered docking assembly
Cooling lines
7. 5
• Slide icemaker into louvered docking
assembly
➊
• Insert ice transport tube into coupling and
tighten nut  rmly
➋
Ice transport tube
7. 6
• Connect cooling water lines to
icemaker
➊
• Water valve is set at the factory. DO NOT
remove seal or adjust water valve
➋
Cooling lines and power
7. 8
Water-cooled icemakers – follow steps 7.5 through 7.10.
In
Out
➊
➋
➋
➊
16
self-contained HARMONY • TOP-MOUNT
• Remove twist tie
• Carefully pass plug thru opening and plug
into wall outlet
Power cord
7. 9
• Position plate into opening and secure
with supplied screw
Power cord
7. 1 0
HARMONY • TOP-MOUNT self-contained
17
Front cover
Install front cover to icemaker.
8
• Slide icemaker cover over machine,
ensuring that tabs on back of cover
slip under louvers on back of louvered
docking assembly
➊,
then tighten two
screws through cover
• Place louvered front cover on machine
➋
Install cover
8.1
NOTICE
Icemaker MUST be sanitized prior to operation!
Consult Operation and Service Manual provided with icemaker for sanitizing instructions.
Upon startup, the icemaker will enter a 15-minute time delay to allow the compressor to equalize and the
evaporator to thaw. If this is the initial start-up, the control board’s reset button can be pressed to start the machine
immediately.
18
self-contained HARMONY • TOP-MOUNT
HARMONY • TOP-MOUNT self-contained
19
00978775R00
© Follett Corporation 7/12
801 Church Lane • Easton, PA 18040, USA
Toll free (877) 612-5086 • +1 (610) 252-7301
www.follettice.com
Horizon, RIDE, and Harmony are trademarks of Follett Corporation.
Follett and Chewblet are registered trademarks of Follett Corporation, registered in the US.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Follett Horizon H_E700AHT Installation Instructions Manual

Follett
Brand
Follett
Model
Horizon H_E700AHT
Type
Installation Instructions Manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents