McQuay CE 10C Installation guide

Brand: McQuay

Model: CE 10C

Category: Split-system air conditioners

Type: Installation guide

CEILING/FLOOR EXPOSED CONVERTIBLE

SPLIT TYPE AIR CONDITIONER

INSTALLATION MANUAL

Group: CEILING EXPOSED

Part Number: A08019025467

Date: MAY 2001

IM-CEC-0501-McQuay

OUTLINE AND DIMENSIONS

Indoor Unit (CE - C Series)

All dimensions are in mm

Model A B C D E F G H I J K L

10C 700 40 36 853 780 680 352 292 235 140 830 250

15C 1050 40 36 1203 1130 680 352 292 235 140 1180 250

20C 1050 40 36 1203 1130 680 352 292 235 140 1180 250

25C 1050 40 36 1203 1130 680 352 292 235 140 1180 250

30C 1400 40 36 1553 1480 680 352 292 235 140 1530 250

40C 1750 40 36 1903 1830 680 352 292 235 140 1880 250

50C 1750 40 36 1903 1830 680 352 292 235 140 1880 250

61C 1750 40 36 1903 1830 680 352 292 285 140 1880 250

62C 1750 40 36 1903 1830 680 352 292 285 140 1880 250

Outdoor Unit (SL-B Series)

All dimensions are in mm

Dimension A B C D E F G H J K L M N P Q R

07B / 07BR

10B / 10BR 740 494 270 266 233 474 47 55 65 166 92 348 318 129 482 68,5

15B / 15BR

20B / 20BR

840 646 330 297 309 626 41 85 75 177 106 408 378 124 592 78,5

25B / 25BR

840

2.5

160

141

SL 30 / 40 / 50 / 60 / 61 C / CR

141,5

746,5

141,5

20,0

448,0

1030,0

850,0

25.0

50,0

85,0

40,0

400,0

320,0

This product is subjected to Waste of Electrical and Electronic Equipment Regulations (WEE

Regulations). The waste product shall be separately collected by specific collection and treatment centre

lease refer to local authorithy for these centres. This is only applicable to European Union countries

Ce produit est soumis

la r

chets

lectriques e

lectroniques (r

chet doi

tre collect

par

ent par un centre de collect

et de traitement s

cifique. Veuillez vous r

s locales pour conna

tre ces centres. Ceci

îî

enne

Questo prodotto

soggetto alle disposizioni RAEE (Rifiuti di apparecchiature elettriche ed elettroniche)

ritirato da un centro incaricato del ritiro e smaltimento. Per conoscere il

ome del centro pertinente, contattare le autori

locali. Questa disposizione

valida solamente i paes

’

ctrico y Electr

ico en materia d

ado se

fico

íí

de colecc

Europea

Dieses Produkt unterliegt den Bestimmungen zur Entsorgung von elektrischen und elektronische

tes

ää

getrennt vom Hausm

ll bei Ihrer

tlichen

ndiges Abfall-Amt. Dieser

ää

Hinweis gilt nur f

nder der Europ

ää

ischen Union

анног

авил

Ев

опейског

Scharfe Kanten und Wärmetauscherflächen stellen eine Gefahrenquelle dar. Jeglicher

Kontakt mit diesen Stellen ist zu vermeiden.

! Vorsicht

! Cautela

Per preservarsi da eventuali ferite, evitare di toccare gli spigoli afilati e la superficie dei

serpentini.

! Cuidado

Los Bordes afilados y la superficie del serpentín pueden producir lesiones. Evite tocarlos.

! Осторожно

Острые края и поверхности змеевиков являются потенциальными

местами нанесения травм. Остерегайтесь контакта с этими местами.

Sharp edges and coil surfaces are potential locations which may cause injury hazards. Avoid

from being in contact with these places.

! Caution

! Avertissement

Les bords coupants et les surfaces du refroidisseur tuulaire présentent un risque

de blessure. Mieux vaut éviter le contact avec ces endroits.

NOTICE

1-1

English

This manual provides the procedures of installation to ensure a safe and good standard of operation for the air

conditioner unit.

Special adjustment may be necessary to suit local requirements.

Before using your air conditioner, please read this instruction manual carefully and keep it for future reference.

INSTALLATION MANUAL

CEILING/FLOOR EXPOSED CONVERTIBLE SPLIT TYPE AIR

CONDITIONER

MODEL

COOLING UNIT

CE 10C / MCM 010C

SL 10B / MLC 010B

CE 15C / MCM 015C

SL 15B / MLC 015B

CE 20C / MCM 020C

SL 20B / MLC 020B

CE 25C / MCM 025C

SL 25B / MLC 025B

CE 30C / MCM 030C

SL 30C / MLC 030C

CE 35C / MCM 035C

SL 35C / MLC 035C

CE 40C / MCM 040C

SL 40C / MLC 040C

CE 50C / MCM 050C

SL 50C / MLC 050C

CE 61C / MCM 061C

SL 60C / MLC 060C

SL 61C / MLC 061C

CE 62C / MCM 062C

SL 60C / MLC 060C

SL 61C / MLC 061C

Part No.: A08019025467

HEAT PUMP

CE 10CR / MCM 010CR

SL 10BR / MLC 010BR

CE 15CR / MCM 015CR

SL 15BR / MLC 015BR

CE 20CR / MCM 020CR

SL 20BR / MLC 020BR

CE 25CR / MCM 025CR

SL 25BR / MLC 025BR

CE 30CR / MCM 030CR

SL 30CR / MLC 030CR

CE 35CR / MCM 035CR

SL 35CR / AMLC 035CR

CE 40CR / MCM 040CR

SL 40CR / MLC 040CR

CE 50CR / MCM 050CR

SL 50CR / MLC 050CR

CE 61CR / MCM 061CR

SL 60CR / MLC 060CR

SL 61CR / MLC 061CR

CE 62CR / MCM 062CR

SL 60CR / MLC 060CR

SL 61CR / MLC 061CR

IM-CEC-0501 (1)-McQuay

1-2

SAFETY PRECAUTIONS

Before installing the air conditioner unit, please read the following safety precautions carefully.

! Warning

• Installation and maintenance should be performed by qualified persons who are familiar with local code and

regulation, and experienced with this type of appliance.

• All field wiring must be installed in accordance with the national wiring regulation.

• Ensure that the rated voltage of the unit corresponds to that of the name plate before commencing wiring work

according to the wiring diagram.

• The unit must be GROUNDED to prevent possible hazard due to insulation failure.

• All electrical wiring must not touch the refrigerant piping, compressor and any moving parts of the fan motors.

• Confirm that the unit has been switched OFF before installing or servicing the unit.

IMPORTANT

DO NOT INSTALL OR USE THE AIR CONDITIONER UNIT IN A LAUNDRY ROOM.

CONTENTS

- Outline And Dimensions page i-ii

- Safety Precautions page 2

- Air Conditioner Parts Description page 3

- Installation Of The Indoor Unit page 3

- Installation Of The Outdoor Unit page 4

- Refrigerant Piping page 5

- Electrical Wiring Connection page 6

- Vacuuming And Charging Method page 9

- Additional Charge page 11

- Overall Checking page 11

- Auto Random Re-Start Function page 11

- Service And Maintenance page 12

- Trouble Shooting page 12

! Caution

Please take note on the following important points when installing.

• Do not install the unit where leakage of flammable gas may occur.

If gas leaks and accumulates at the surrounding of the unit, it may cause fire ignition.

• Ensure that the drainage piping is connected properly.

If the drainage piping is not connected properly, it may cause water leakage which will dampen the

furniture.

• Do not overcharge the unit.

This unit is factory pre-charged. Overcharge will cause over-current or damage to the compressor.

• Ensure that the unit panel is covered back after service or installation.

Unsecured panel will cause unit to operate noisily.

1-3

English

AIR CONDITIONER PARTS DESCRIPTION

Indoor Unit

Air Discharge Louver

Outdoor Unit

Air Intake

Air Discharge Nozzle

Indicator Lights

Refrigerant Piping

Air Discharge Grille

Air Intake Grille

Air Filters

(Inside Air Intake Grille)

Fig. A

Signal Receiver

Air Intake

Please ensure that the following steps are taken:

• Check the gradient for drainage flow as recommended in Figure B.

• Provide clearance for easy servicing and optimal air flow as

shown in Figure C.

• The indoor unit must be installed such that there is no short

circuit of the cool discharge air with the warm return air.

• Do not install the indoor unit where there is direct

sunlight shining on the unit. The location should be

suitable for piping and drainage installation. The unit must be

a large distance away from the door.

Fig. B

Preliminary Site Survey

• Electrical supply and installation shall conform to the local

authority (e.g. National Electrical Board).

• Voltage supply fluctuation must not exceed ±10% of the rated

voltage. Electricity supply lines must be independent of weld-

ing transformers which can cause high supply fluctuation.

• Ensure that the installation location is convenient for wiring

and piping.

Standard Mounting

Ensure that the overhead supports are strong enough to hold the

weight of the unit. Position the hanger rods (wall

mounting bracket for floor standing), and check for its

alignment with the unit. Also, check that the hangers are secured

and the base of the fan coil unit is leveled in both horizontal direc-

tions, taking into account the gradient for drainage flow as recom-

mended in Figure B.

INSTALLATION OF THE INDOOR UNIT

Fig. C

Semi-Enclose Mounting

• In case the unit is to be half recessed into false ceiling, please

check the unit is well aligned.

• Provide the installation space as shown in Figure D.

Fig. D

Utensils, furnitures or built-in

architectural features must not

protrude more than 250.0 mm

Top Panel Of Unit

10mm

1.0m (Min.)

10mm (Lower)

400mm (Min.)

Drainage Pipe Side

5mm (Min.)

250mm (Max.)

300mm (Min.)

500mm (Min.)

10mm

Ceiling Board

10mm

140 mm

10mm

300mm (Min.)

10mm

621mm

1-4

INSTALLATION OF THE OUTDOOR UNIT

Fig. E

Fig. F

• The location must be well-ventilated, so that the unit

can draw in and distribute plenty of air thus lowering

the temperature.

• A place capable of bearing the weight of the outdoor

unit as well as isolating noise and vibration.

• A place protected from the direct sunlight. Use an

awning for protection if necessary. See Figure I.

• Ensure that there is no obstruction to the air flowing

into or out of the unit. Remove any obstacles that block

the air intake or air discharge. See Figure G and H.

• Install the outdoor condensing unit in such a way that

the hot air distributed cannot be drawn in again (as in

the case of short circuit of hot discharge air). Allow

sufficient space for maintenance work around the unit.

See Figure E and F.

Fig. G

Fig. H

• The installation location must not be susceptible to highly

concentrated dust, oil, salt or sulfide gas.

Outdoor Unit Clearance

SL Series (See Fig. J & K)

All Model A B C D

Minimum Distance (mm)

300 1000 300 500

Fig. J

Air

Inlet

Obstacle

Fig. I

Fig. K

Obstacle

Service

Space

Air

Inlet

Air

Discharge

1-5

English

! Caution

If the outdoor condensing unit is operated in an atmosphere containing oils (including machine oils), salt (coastal area),

sulfide gas (nearby hot spring or oil refinery plant), such substances may lead to failure of the unit.

REFRIGERANT PIPING

Maximum Pipe Length And Maximum Number Of Bends

If the pipe length is too long, both the capacity and the

reliability of the unit will decrease. As the number of bends

increases, resistance of the piping system to the refrigerant

flow increases and thus lowering the capacity, as a result

the compressor may become defective. See Figure N and

Figure O.

Elevation

Outdoor Unit

Piping Length

Indoor Unit

Fig. N

Indoor Unit

Maximum

Piping 20m

Max. Elevation Height

Model 20 25 30 40 50 60 61

Maximum Length (m) 15 15 20 20 20 20 20

Maximum Elevation (m) 8 8 10 10 10 10 10

Maximum Number of Bends 10 10 10 10 10 10 10

Therefore, always select the shortest path for the piping

system and follow the recommendations as tabulated in the

table.

Fig. O

Piping Works And Flaring Technique

• Do not use contaminated or damaged copper tubing. If any pipings, evaporator or condenser had been exposed or had been

opened for 15 seconds or more, then vacuum and purge with field supplied refrigerant. Generally, do not remove plastic,

rubber plugs and brass nuts from the valves, fittings, tubings and coils until it is ready to connect suction or liquid line into

valves or fittings.

• If any brazing work is required, ensure that the nitrogen gas is passed through coil and joints while the brazing work is

being done. This will eliminate soot formation on the inside walls of the copper tubings.

• Cut the pipe stage by stage, advancing the blade of the pipe cutter slowly. Extra force and deep cut will cause more

distortion on the pipe and thus extra burr. See Figure P.

1/4t

Cutting Copper Tube

Fig. Q

Fig. P

Remove Burr

Fig. R

Copper Tube

Swaging Block

• Remove burrs from cut edges of the pipes with remover

as shown in Figure O. This will avoid unevenness on

the flare faces which will cause gas leak. Hold the end

of the pipe downwards to prevent metal chips from

entering the pipe.

• Insert the flare nuts, mounted on the connection parts of

both the indoor unit and outdoor unit, onto the copper

pipes.

• The exact length of pipe protruding from the face of the

flare die is determined by the flaring tool. See Figure R.

The table shows the use of an imperial die and rigid die.

• Fix the pipe firmly on the flare die. Match the centers of

both the flare die and the flaring punch, and then tighten

the flaring punch fully.

Piping Connection To The Units

• Align the center of the piping and tighten the flare nut

sufficiently with fingers.

• Finally, tighten the flare nut with the torque wrench until

the wrench clicks.

• When tightening the flare nut with the torque wrench,

ensure that the tightening direction follows the arrow

indicated on the wrench.

1-6

Ø Tube, D A (mm)

Inch mm Imperial Rigid

1/4" 6.35 1.3 0.7

3/8" 9.52 1.6 1.0

1/2" 12.70 1.9 1.3

5/8" 15.88 2.2 1.7

3/4" 19.05 2.5 2.0

Spanar Torque Wrench

Indoor Piping

Flare Nut

Flared Tube

Flare Joint

Pipe Size (mm/in) Torque (Nm)

6.35 (1/4) 18

9.53 (3/8) 42

12.7 (1/2) 55

15.88 (5/8) 65

19.05 (3/4) 78

ELECTRICAL WIRING CONNECTION

Electrical Wiring Connection For CE Series 10~25C

Indoor Unit CE 30C CE 35C

Outdoor Unit SL 30C SL 35C

Voltage range (2) 220V – 240V/1Ph/50Hz + ! or 208V - 230V/1Ph/60Hz+!

Recommended fuse (1) A 25 25

Power Supply Cable size mm

4.0 4.0

Number of conductors (1) 33

Interconnection Cable size mm

4.0 4.0

Number of conductors (1) 44

Electrical Wiring Connection For CE Series 30~35C

The electrical power must be provided with

protection devices (circuit breaker or fuse)

with double pole separation system (phase +

neutral) with minimum contact gap of 3mm.

Terminal Strip

Indoor Unit

Interconnection Cable

Terminal Strip

Outdoor Unit

COMP

Indoor Unit CE 10C CE 15C CE 18C CE 20C CE 25C

Outdoor Unit SL 10B SL 15B SL 18B SL 20B SL 25B

Voltage range (2) 220V – 240V/1Ph/50Hz + ! or 208V - 230V/1Ph/60Hz+!

Recommended fuse (1) A 10 10 16 16 20

Power Supply Cable size mm

1.5 1.5 2.5 2.5 2.5

Number of conductors (1) 3333 3

Interconnection Cable size mm

1.5 1.5 2.5 2.5 2.5

Number of conductors (1) 3333 3

CE 10~25C

Power Supply

Cable

IMPORTANT: (1) These values are for information only, they should be checked and selected to comply with the local and/

or national codes and regulations. They are also subjected to the type of installation and size of conductors

used.

(2) The appropriate voltage range should be checked with label data on the unit. ETL listed unit is only

applicable to 60Hz power supply only.

1-7

English

The electrical power must be provided with

protection devices (circuit breaker or fuse) with

double pole separation system (phase + neutral)

with minimum contact gap of 3mm.

Electrical Wiring Connection For CE Series 40 ~ 62C

Indoor Unit CE 40C CE 50C CE 61C/CE 62C

Outdoor Unit SL 40C SL 50C SL 60C/SL 61C

Voltage range (2) 380V – 420V/3Ph/50Hz+N + ! or 208V-230V/3Ph/60Hz+N+!

Recommended fuse (1) A (50/60Hz) 10/20 16/25 16/25

Power Supply Cable size mm

(50/60Hz) 1.5/2.5 2.5/4.0 2.5/4.0

Number of conductors (1) 55 5

Interconnection Cable size mm

(50/60Hz) 1.5/1.5 1.5/1.5 1.5/1.5

Number of conductors (1) 44 4

IMPORTANT: (1) These values are for information only, they should be checked and selected to comply with the local and/

or national codes and regulations. They are also subjected to the type of installation and size of conductors

used.

(2) The appropriate voltage range should be checked with label data on the unit. ETL listed unit is only

applicable to 60Hz power supply only.

The electrical power must be provided with

protection devices (circuit breaker or fuse)

with double pole separation system (phase +

neutral) with minimum contact gap of 3mm.

COMP

Terminal Strip

Indoor

Unit

Interconnection Cable

Terminal Strip

Outdoor

Unit

Power Supply

Cable

Terminal Strip

Indoor

Unit

Interconnection Cable

Terminal Strip

Outdoor

Unit

Power Supply

Cable

Electrical Wiring Connection For CE 10/15/20/25CR (Heat Pump)

COMP

Indoor Unit CE 10CR CE 15CR CE 20CR CE 25CR

Outdoor Unit SL 10BR SL 15BR SL 20BR SL 25BR

Voltage range (2) 220V – 240V/1Ph/50Hz + ! or 208V – 230V/1Ph/60Hz + !

Power Supply Cable size mm

1.5 1.5 2.5 2.5

Number of conductors (1) 33 3 3

Interconnection Cable size mm

1.5 1.5 2.5 2.5

Number of conductors (1) 55 5 5

Recommended fuse A 10 10 16 20

CE 30C

CE 40C/50C/61C

1-8

COMP

4WV

COMP

4WV

The electrical power must be provided with

protection devices (circuit breaker or fuse)

with double pole separation system (phase +

neutral) with minimum contact gap of 3mm.

Interconnection Cable

Terminal

Strip

Indoor

Unit

Terminal Strip

Outdoor Unit

CE 30CR

Indoor unit CE 30CR

Outdoor unit SL 30CR

Voltage range (2) 220V – 240V/1Ph/50Hz + ! or 208V – 230V/1Ph/60Hz + !

Power Supply Cable size mm

4.0

Number of conductors (1) 3

Interconnection Cable size mm

4.0

Number of conductors (1) 7

Recommended fuse (1) A 25

The electrical power must be provided with

protection devices (circuit breaker or fuse)

with double pole separation system (phase +

neutral) with minimum contact gap of 3mm.

Interconnection Cable

Terminal

Strip

Indoor

Unit

Terminal Strip

Outdoor Unit

COMP

4WV

COMP

4WV

CE 30CR

Indoor unit CE 40CR CE 50CR CE 61/62CR

Outdoor unit SL 40CR SL 50CR SL 60CR/61CR

Voltage range (2) 380V – 415V/3Ph/50Hz + N + ! or 208V – 230V/3Ph/60Hz + N + !

Power Supply Cable size mm

(50/60Hz) 1.5/2.5 2.5/4.0 2.5/4.0

Number of conductors (1) 55 5

Interconnection Cable size mm

(50/60Hz) 1.5/1.5 1.5/1.5 1.5/1.5

Number of conductors (1) 77 7

Recommended fuse (1) A (50/60Hz) 10/20 16/25 16/25

Power Supply

Cable

Power Supply

Cable

Outdoor Coil Sensor

IMPORTANT: (1) These values are for information only, they should be checked and selected to comply with the local and/

or national codes and regulations. They are also subjected to the type of installation and size of conductors

used.

(2) The appropriate voltage range should be checked with label data on the unit. ETL listed unit is only

applicable to 60Hz power supply only.

1-9

English

1) Open the suction service port cap.

2) Manifold gauge connection:

• Low side hose from manifold gauge to the suction

service port.

• Service (center) hose from manifold gauge to the

vacuum pump.

3) Evacuate for approximately one hour (evacuation time

varies with pump capacity).

• Confirm that the manifold gauge needle has moved

towards -30inHg (-76cmHg).

4) Close the low side valve on the manifold gauge, turn

off the vacuum pump and confirm that the gauge needle

does not move (approximately 3 minutes after turning

off the vacuum pump).

5) Disconnect the service hose from the vacuum pump.

6) After evacuation, open the valve stem of the discharge

and suction valve counter-clockwise for the gas to run

into the indoor unit.

7) Check the low side pressure after turning on the

compressor for 10 to 15 minutes.

VACUUMING AND CHARGING METHOD

Figure

For 2, 3 way valve

Outdoor Unit

Liquid Side

Discharge

Val ve

Indoor Unit

Gas Side

Vacuum

Pump

Suction Valve

Open

Low

• The pre-charged outdoor unit does not need any vacuuming or charging. However, once it is connected, the connecting

pipe line and the indoor unit need to be vacuumed before releasing the refrigerant (R22) from the outdoor unit.

Vacuuming Procedure For 2, 3 Way Valve (See Figure S)

! Caution

Ensure that the colors of wires on the outdoor unit and the terminal markings are the same as the indoor unit

respectively.

COMP

4WV

COMP

4WV

The electrical power must be provided with

protection devices (circuit breaker or fuse)

with pole separation system, minimum

contact gap of 3mm.

CE 40/50/61/62 CR

IMPORTANT: (1) These values are for information only, they should be checked and selected to comply with the local and/

or national codes and regulations. They are also subjected to the type of installation and size of conductors

used.

(2) The appropriate voltage range should be checked with label data on the unit. ETL listed unit is only

applicable to 60Hz power supply only.

Interconnection Cable

Terminal

Strip

Indoor

Unit

Terminal Strip

Outdoor Unit

Power Supply

Cable

1-10

Gas Side

Charging

Cylinder

Check Valve

Open

Suction

Val ve

Discharge

Valve

Indoor Unit

Outdoor Unit

Liquid Side

Open

Low

Figure U

For 2, 3 way valve

• Stopping half-way will cause the gas to be

discharged.

• If the system has been charged with liquid

refrigerant while operating the air conditioner, then

turn off the air conditioner before disconnecting the

hose.

5) Mount the valve stem nuts and service port nut.

• Be sure to check for any gas leakage.

Vacuuming Procedure For 2 x 3 Way Valve

(See Figure T)

1) Open the suction and discharge service port cap.

2) Manifold gauge connection:

• Low side hose from manifold gauge to the suction

service port.

• High side hose from manifold gauge to the discharge

service port.

• Service (center) hose from manifold gauge to the

vacuum pump.

3) Turn "ON" the power switch of the vacuum pump and

make sure that needle in the manifold gauge moved

towards -30 inHg (-76 cmHg).

4) Close the valve of both the low and high sides on the

manifold gauge, turn "OFF" the vacuum pump and

confirm that the gauge needle does not move

(approximately 3 minutes after turning "OFF" the

vacuum pump).

5) Disconnect the service hose from the vacuum pump.

Charging Procedure For 2, 3 Way Valve

(See Figure U)

1) Connect the service hose from manifold gauge to

the charging cylinder.

• Connect the service hose, which you have

disconnected from the vacuum pump, to the valve at

bottom of the cylinder.

• If you are using a gas cylinder, then use a scale and

reverse the cylinder so that the system can be charged

with liquid.

2) Purge the air from the service hose.

• Open the valve at the bottom of the cylinder and

press the check valve suction on the manifold gauge

to purge the air (be careful with the liquid

refrigerant). The procedure is the same if you are

using a gas cylinder.

3) Open the valve (low side) on the manifold gauge

and charge the system with liquid refrigerant.

• If the system cannot be charged with the specified

amount of refrigerant, then it should be charged little

by little (approximately 150g at each time) while

operating the air conditioner under cooling cycle.

However, one time is not sufficient, wait

approximately 1 minute and then repeat the

procedure.

4) Immediately disconnect the service hose from the

suction valve's service port.

6) After that, open the valve stem of the discharge and

suction valve counter-clockwise for the gas to run into

the indoor unit.

7) Check the low side pressure after turning "ON" the

compressor for 10 to 15 minutes.

Figure T

For 2 x 3 way valve

Gas Side

Open

Indoor Unit

Liquid Side

Discharge

Val ve

Suction Valve

Vacuum Pump

Outdoor Unit

Open

Indoor 27°C/Outdoor 35°C Indoor 32°C/Outdoor 43°C

Kg/cm

Psig Kg/cm

Psig

SL 10B 4.5 – 5.6 65.4 – 79.6 5.2 – 6.3 74.0 – 89.6

SL 15B 4.5 – 5.6 65.4 – 79.6 5.2 – 6.3 74.0 – 89.6

SL 18B 4.5 – 5.8 65.4 – 82.5 5.2 – 6.8 74.0 – 93.9

SL 20B 4.5 – 5.6 65.4 – 79.6 5.2 – 6.3 74.0 – 89.6

SL 25B 4.0 – 4.8 56.9 – 68.3 4.5 – 5.0 64.0 – 71.1

SL 30C 4.9 – 5.3 70.0 – 75.0 19.3 – 19.6 275 – 280

SL 35C 4.9 – 5.4 70.0 – 75.1 19.3 – 19.7 276 – 280

SL 40C 4.9 – 5.5 70.0 – 75.2 19.3 – 19.8 277 – 280

SL 50C 4.9 – 5.6 70.0 – 75.3 19.3 – 19.9 278 – 280

SL 60C 4.9 – 5.5 70.0 – 75.3 19.3 – 19.9 278 – 280

SL 61C 4.9 – 5.5 70.0 – 75.3 19.3 – 19.9 278 – 280

• Within the value - refrigerant cycle normal.

• Lower than the value - refrigerant cycle has leaks. Checking, repairing and top-up is necessary.

• Too low (Ω zero) - needs evacuation and charge.

! Caution

This is different from the previous procedures. As you are charging with liquid refrigerant from the gas side (suction

line), absolutely do not attempt to charge with large amount of liquid refrigerant while operating the air conditioner.

1-11

English

OVERALL CHECKING

• Ensure that:

1) The unit has been mounted solidly and rigid in

position.

2) The piping and connections are leak-proof after the

charging.

3) Proper wiring has been installed.

• Drainage check

– pour some water into the left side of the drain pan

(the drainage is at the right side of the unit).

• Test run:

1) Conduct a test run on the unit after having perform

the water drainage test and the gas leakage test.

2) Check the following items:

a) Is the electrical plug inserted firmly into the socket?

b) Is there any abnormal sounds from the unit?

c) Is there any abnormal vibrations on the unit or the

piping?

d) Is the drainage of water smooth?

• Confirm that:

1) The condenser fan is running. Check the warm air

blowing from the condensing unit.

2) The evaporator blower is running and discharge cool

air.

3) The suction (low side) pressure is as recommended.

4) The remote controller incorporates a 3-minute delay

protection in the circuit, whereby the outdoor

condensing unit requires about 3 minutes delay

before it can start operating.

ADDITIONAL CHARGE

• The refrigerant gas has already been charged into the

outdoor unit. If the piping length is not more than 5m,

then additional charge of the refrigerant after

vacuuming is not necessary.

• When the piping length is more than 5m, please use the

charge as tabulated in the table.

Figure V

For 2 x 3 way valve

1) Connect the service hose from the manifold gauge to

the charging cylinder.

• Connect the service hose, which you have

disconnected from the vacuum pump, to the valve at

the bottom of the cylinder.

• If you are using a gas cylinder, then use a scale and

reverse the cylinder so that the system can be charged

with liquid.

2) Purge the air from the service hose.

• Open the valve at the bottom of the cylinder and press

the check valve suction on the manifold gauge to

purge the air (be careful with the liquid refrigerant).

The procedure is the same if you are using a gas

cylinder.

3) Open the valve (high side) on the manifold gauge

and charge the refrigerant to the system (unit).

• Be sure to open only the valve (high side) on the

manifold gauge to charge the system from the

discharge pipe (liquid side).

4) Immediately disconnect the service hoses from the

3-way valve service port.

Charging Procedure For 2 X 3 Way Valve (See Figure V)

Open

Charging

Cylinder

Indoor Unit

Outdoor Unit

Liquid Side

Discharge

Va l v e

Open

Gas Side

Suction

Va l v e

Check

Valve

5) Mount the valve nuts and the service port nut onto

the 3-way valve.

• Be sure check for any gas leakage.

AUTO RANDOM RE-START FUNCTION

If there is a power cut when the unit is operating, it will automatically resume the same operating mode when the power

is restored. (Applicable only to units with this feature)

! Caution

Before turning off the power supply, set the remote controller’s ON/OFF switch to the “OFF” position to prevent the

nuisance tripping of the unit.

If this is not done, the unit’s fans will start turning automatically when power resumes, posing a hazard to service

personnel or the user.

! Warning

• Disconnect from the main power supply before servicing the air conditioner unit.

• DO NOT pull out the power cord when the power is ON. This may cause serious electrical shocks which may

result in fire hazards.

Model R22 Charge (g/m)

7m 10m 15m 20m

20C / 20CR 30/50 75/125 150/250 225/375

25C / 25CR 76/100 190/250 380/500 570/750

30C / 30CR 100/100 250/250 500/500 750/750

40C / 40CR 100/100 250/250 500/500 750/750

50C / 50CR 100/100 250/250 500/500 750/750

61C / 61CR 100/100 250/250 500/500 750/750

62C / 62CR 100/100 250/250 500/500 750/750

1-12

SERVICE AND MAINTENANCE

Maintenance Procedures

1. Remove any dust adhered on the filter by using a vacuum

cleaner or wash in lukewarm water (below 40°C) with neutral

cleaning detergent.

2. Rinse well and dry the filter before placing it back onto the

unit.

3. Do not use gasoline, volatile substances or chemical to clean

the filter.

1. Clean any dirt or dust on the grille or panel by wiping it using

soft cloth soaked in lukewarm water (below 40°C) with

neutral detergent solution.

2. Do not use gasoline, volatile substances or chemical to clean

the indoor unit.

1. Check its cleanliness and clean it if necessary.

1. Check for any abnormal noise.

1. Check and remove any dirt clogged between the fins.

2. Check and remove any obstacles that hinder air flowing into

and out of the indoor/outdoor unit.

1. Check the voltage and current of the indoor and outdoor unit.

2. Check the electrical wiring for any faulty contacts caused by

loose connections, foreign matters, etc. Tighten the wires onto

the terminal block if necessary.

1. No maintenance needed if the refrigerant circuit remain sealed.

However, check for any refrigerant leaks at all joints and

fitting.

1. The compressor oil is factory-precharged. It is not necessary

to add any oil if the circuit remains sealed.

1. All motor pre-lubricated and sealed at factory.

Period

At least once

every 2 week.

More frequently if

necessary.

At least once

every 2 weeks.

More frequently if

necessary.

Every 3 months.

When necessary.

Every month.

Every 2 months.

Every 6 months.

No maintenance

required.

No maintenance

required.

Service Parts

Indoor air filter

Indoor unit

Condense drain pan & pipe

Indoor fan

Indoor/outdoor coil

Power supply

Compressor

Compressor oil

Fan motor oil

When any malfunction of the air conditioner unit is noted, immediately switch off the power supply to the

unit. Check the following fault conditions and causes for some simple trouble shooting tips.

TROUBLE SHOOTING

Causes

- Protection against frequent starting. Wait for 3 to 4

minutes for the compressor to start operate.

- Power failure, or the fuse need to be replaced.

- The power plug is disconnected.

- It is possible that your delay timer has been set incorrectly.

- If the fault persist after all these verifications, please

contact the air conditioner unit installer.

- The air filter is dirty.

- The doors or windows are open.

- The air suction and discharge are clogged.

- The regulated temperature is not high enough.

- Battery flat.

- The batteries are placed incorrectly.

- Odors may be caused by cigarettes, smoke particles,

perfume etc. which might have adhered onto the coil.

- This is caused by air humidity after an extended long

period of operation.

- The set temperature is too low, increase the temperature

setting and operate the unit at high fan speed.

- Check the condensate evacuation.

- Refrigerant fluid flowing into the evaporator coil.

Fault

1. The compressor does not start operate after 3 minutes

from starting the air conditioner unit.

2. The air conditioner unit does not operate.

3. The air flow is too low.

4. The remote control display is dim.

5. Discharge air flow has bad odor.

6. Condensation on the front air grille of the indoor unit.

7. Water flowing out from the air conditioner unit.

8. Hissing air flow sound from the air conditioner unit

during operation.

If the fault persists, please call your local dealer / serviceman.

Do not operate any heating apparatus too close to the air conditioner unit. This may

cause the plastic panel to melt or deform as a result of the excessive heat.

! Caution

2-1

Français

Ce manuel fournit les procédures d’installation pour assurer le bon fonctionnement et la sécurité de cet appareil.

Des ajustements peuvent être nécéssaires pour suivre les réglementations locales.

Avant d’installer et de faire fonctionner le climatiseur, lisez attentivement ce manuel et conservez le.

MANUEL D'INSTALLATION

CLIMATISEUR SPLIT CONVERTIBLE MONTAGE APPARENT

PLAFOND / SOL

MODÉLE

FROID SEUL

CE 10C / MCM 010C

SL 10B / MLC 010B

CE 15C / MCM 015C

SL 15B / MLC 015B

CE 20C / MCM 020C

SL 20B / MLC 020B

CE 25C / MCM 025C

SL 25B / MLC 025B

CE 30C / MCM 030C

SL 30C / MLC 030C

CE 35C / MCM 035C

SL 35C / MLC 035C

CE 40C / MCM 040C

SL 40C / MLC 040C

CE 50C / MCM 050C

SL 50C / MLC 050C

CE 61C / MCM 061C

SL 60C / MLC 060C

SL 61C / MLC 061C

CE 62C / MCM 062C

SL 60C / MLC 060C

SL 61C / MLC 061C

POMPE À CHALEUR

CE 10CR / MCM 010CR

SL 10BR / MLC 010BR

CE 15CR / MCM 015CR

SL 15BR / MLC 015BR

CE 20CR / MCM 020CR

SL 20BR / MLC 020BR

CE 25CR / MCM 025CR

SL 25BR / MLC 025BR

CE 30CR / MCM 030CR

SL 30CR / MLC 030CR

CE 35CR / MCM 035CR

SL 35CR / AMLC 035CR

CE 40CR / MCM 040CR

SL 40CR / MLC 040CR

CE 50CR / MCM 050CR

SL 50CR / MLC 050CR

CE 61CR / MCM 061CR

SL 60CR / MLC 060CR

SL 61CR / MLC 061CR

CE 62CR / MCM 062CR

SL 60CR / MLC 060CR

SL 61CR / MLC 061CR

Part No.: A08019025467

IM-CEC-0501 (1)-McQuay

2-2

PRÉCAUTIONS DE SÉCURITÉ

Avant de faire fonctionner l'appreil, veuillez bien lire les précautions de sécurité suivantes.

! Attention

• L'installation et la maintenance doivent être exécutées par une personne qualifiée qui est familiarisée avec les lois

et réglementations en vigueur, et aussi expérimentée dans ce type d'équipements.

• Tous les câblages doivent répondre aux réglementations électriques nationales.

• Avant de commencer le raccordement suivant le schéma électrique, s’assurer que la tension nominale de l’appareil

corresponde bien à celle indiquée sur la plaque signalétique.

• L' unité doit être raccordée à la TERRE pour prévenir tous les risques possibles dûes à un défaut d'isolation.

• Aucun câble électrique ne doit toucher la tuyauterie du réfrigérant, le compresseur ou les pièces mobiles des moteurs

de ventilation.

• Avant l’installation ou l’entretien du climatiseur, s’assurer que l’appareil est éteint (OFF).

IMPORTANT

NE PAS INSTALLER OU UTILISER LE CLIMATISEUR DANS UNE BUANDERIE.

SOMMAIRE

- Contour Et Dimensions page i-ii

- Précautions De Sécurité page 2

- Description Du Climatiseur page 3

- Installation De L’unité Intérieure page 3

- Installation De L’unité Extérieure page 4

- Tuyauteries Frigorifiques page 5

- Raccordement Électrique page 6

- Procedure De Tirage Au Vide Et De Charge page 9

- Charge Additionnelle page 11

- Vérifications Generale page 11

- Fonction De Redemarrage Au Hasard Automatique page 11

- Entretien Et Maintenance page 12

- Analyse Des Causes De Dysfonctionnement Du Climatiseur page 12

! Avertissement

Vérifier les points suivants au cours de l’installation.

• Ne pas installer l'appareil où il peut se produire des fuites de gaz inflammable.

En cas de fuite et accumulation de gaz autour de l’appareil, il y a risque d’incendie.

• S’assurer que le tuyau d’évacuation du condensat est correctement branché.

Si le tuyau d’évacuation n’est pas correctement branché, les éventuelles fuites d’eau risquent de mouiller

le mobilier.

• Ne pas surcharger l'unité (en fluide frigorigène).

Cet appareil est préchargé en usine. Une charge trop importante risque de provoquer une surcharge

électrique ou d’endommager le compresseur.

• S’assurer que le panneau supérieur de l’appareil est remis en place après l’installation ou l’entretien.

Avec un panneau mal fixé l’appareil va fonctionner bruyamment.

2-3

Français

DESCRIPTION DU CLIMATISEUR

Unite Interieure

Unite Exterieure

Fig. A

Veuillez vous assurer que les points suivants soient faits :

• Vérifier la pente pour l’écoulement du condensat, comme

indiqué en Figure B.

• Laisser un espace de dégagement, comme indiqué en

Figure C, pour faciliter l’entretien et assurer un flux d’air

optimal.

• L’unité intérieure doit être installée de telle manière qu’il

n’y ait pas interférence entre le flux d’air froid et la re-

prise d’air chaud.

• Ne pas installer l’unité intérieure à en endroit directement

exposé au soleil. L’emplacement doit être choisi loin

des portes et permettre la pose des tuyauteries

frigorifiques et d’évacuation du condensat.

Etude Preliminaire Du Site

• L’alimentation électrique et l’installation doivent être

conformes à la réglementation locale (p.ex. agréé EDF).

• Les fluctuations de tension du réseau doivent rester dans

la limite de ±10% de la tension nominale. Le climatiseur

ne doit pas partager les lignes d’alimentation électrique

avec des transformateurs de soudage, qui risquent de

causer d’importantes fluctuations.

• S’assurer que l’emplacement de l’appareil convient pour

le câblage et la tuyauterie.

Montage Standard

Assurez-vous que le plafond est suffisamment solide pour

supporter le poids de l’appareil. Positionner les tringles de

suspente (consoles de support mural pour un appareil au sol),

et vérifier si elles sont bien alignées avec l’appareil. S’assurer

également que les tringles sont bien fixées et que la base de

l’appareil est à niveau dans les deux directions horizontales,

en tenant compte de l’inclinaison recommandée pour

l’évacuation du condensat (voir Figure B).

INSTALLATION DE L'UNITE INTERIEURE

Fig. C

Montage Semi-Encastré

• Si l’appareil est semi-encastré dans un faux-plafond,

vérifier qu’il est correctement aligné.

• Prévoir un espace de dégagement comme indiqué en

Figure D.

Conduit De Ventilation

Reprise D'air

Ventilateur

Leds De Visualisation

Récerteur De Signal

Grilles De Ventilation

Grilles De Reprise D'air

Filltre À Air

(Sous La Grille De Reprise A'air)

Tuyauteries Frigorifiques

Reprise D'air

Les pièces de mobilier,

d’équipement ou éléments

d’architecture encastrés ne doivent

pas s’avancer de plus de

250,0 mm.

Face D’èvacuation Des

Condensats

5mm (Min.)

250mm (Max.)

300mm (Min.)

500mm (Min.)

10mm

Fig. D

Panneau Supérieur De L’appareil

Plaque De

Faux-plafond

10mm

140 mm

10mm

300mm (Min.)

10mm

621mm

Fig. B

10mm

1,0m (Min.)

10mm (Bas)

400mm (Min.)

2-4

INSTALLATION DE L'UNITE EXTERIEURE

Fig. F

• L'emplacement doit être bien ventilé de façon à ce que

l'appareil distribue la totalité de l'air à un niveau de

température plus bas.

• L’emplacement doit pouvoir supporter le poids de l’unité

extérieure et isoler du bruit et des vibrations.

• L’emplacement doit être protégé de la lumière directe

du soleil. Installer un auvent si nécessaire. Voir Figure

• S’assurer qu’il n’y a pas d’obstruction sur le passage de

l’air aspiré et refoulé de l’appareil. Retirer tout obstacle

qui pourrait bloquer la reprise ou le refoulement d’air.

Voir Figure G et H.

• Installer le groupe de condensation extérieur de telle

manière que l’air chaud qu’il dégage ne puisse être repris

par un autre appareil (interférence d’air chaud). Prévoir

un espace suffisant autour de l’appareil pour faciliter

l’entretien. Voir Figure E et F.

Fig. G

Fig. H

• L’emplacement ne doit pas être trop exposé à la poussière

ou aux vapeurs d’huile, de sel ou de souffre.

Dégagement De L’unité Extérieure

Série SL (Voir Figure J et K)

Tous Modéle A B C D

Distance Minimume (mm)

300 1000 300 500

Fig. J

Entree D’air

Obstacle

Fig. I

Fig. K

Obstacle

Degagement

Entree D’air

Fig. E

Refoulement D’air

Page is loading ...

McQuay CE 10C Installation guide

Brand: McQuay

Model: CE 10C

Category: Split-system air conditioners

Type: Installation guide

Download PDF

report

in other languages

italiano: McQuay CE 10C Guida d'installazione
français: McQuay CE 10C Guide d'installation
español: McQuay CE 10C Guía de instalación
Deutsch: McQuay CE 10C Installationsanleitung
русский: McQuay CE 10C Инструкция по установке

McQuay CE 10C Installation guide

McQuay CE 10C Installation guide

in other languages

Related papers

Other documents