Simplicity 63086 User manual

Brand: Simplicity

Model: 63086

Category: Lawnmowers

Type: User manual

Simplicity 63086 is a grass catcher kit for Snapper 26” steel deck walk behind mowers. This kit converts the side discharge mower into grass bagging capability. The kit includes a grass catcher bag, bag support, air lifts for the blade and an adapter to mount to the deck. The grass catcher bag has a capacity of 2.5 bushels and is made of durable polyester fabric. The bag support is made of steel and is designed to securely hold the bag in place. The air lifts help to improve the airflow under the deck, which results in better grass collection.

#6-3086 GRASS CATCHER KIT for

SNAPPER 26” STEEL DECK WALK BEHIND MOWERS

INTRODUCTION: This kit includes a grass catcher bag, bag support, air lifts for the blade and an adapter to mount to

the deck. This kit will convert the side discharge mower into grass bagging capability. Install the kit as follows:

WARNING

DO NOT attempt any adjustments, maintenance, repairs, or service with engine running. Stop engine. Stop

blade. Remove spark plug wire and secure wire away from spark plug. Engine, muffler and surrounding areas

are extremely hot. Avoid serious burns; allow components to cool down before installing kit. DO NOT operate

machine without recycling cover, deflector or entire grass catcher installed. Inspect grass catcher frequently

for wear or deterioration. Replace worn or damaged parts prior to operating. Wear heavy leather gloves when

handling or working around cutting blades. Blades are extremely sharp and can cause severe injury. Make sure

that fuel cap is tightened securely. If machine leaks fuel from cap when tilted back on the rear wheels then fuel

tank must be drained of all fuel. Use approved fuel container. DO NOT smoke near open fuel container. DO NOT

fill fuel tank indoors or when engine is running. Allow engine to cool for at least ten minutes before refilling.

Wipe off any spilled fuel before starting engine.

STEP 1: Rotate deflector up and out of the way.

Install adapter and secure with bolts, washers and

nuts. Tighten securely. See Figure 1.

FIGURE 1

STEP 2: Slide plastic cap over end of support. Install

bolts, spacers, lock washers and nuts into the bag

support. Tighten nuts and bolts securely. See Figure 2.

FIGURE 2

STEP 3: Align the bag support with middle handle,

use the holes in the bag support to mark then drill

three 9/32” holes in middle handle. IMPORTANT:

Make sure bag support is aligned with middle handle

before marking and drilling. Install bag support to

the upper portion of middle handle. Tighten nuts and

bolts securely. See Figure 3.

FIGURE 3

INSTRUCTION No. 7-2194 (I.R. 5/14/99)

SECURE ADAPTER

WITH BOLTS, NUTS

AND WASHERS

INSTA

LL BOLTS, SPACERS,

LOCK WASHERS AND NUTS

ROTATE DEFLECTOR

UP, OUT OF THE WAY

ADAPTER

SLIDE PLASTIC CAP

OVER END OF BAG

SUPPORT

POSITION BAG SUPPORT

OVER MIDDLE HANDLE,

MARK AND DRILL ONE 9/32”

HOLE IN THE VERTICAL

PORTION OF HANDLE.

POSITION BAG SUPPORT

OVER MIDDLE HANDLE,

MARK AND DRILL TWO

9/32” HOLES IN THE

HORIZONTAL PORTION

OF HANDLE

STEP 4: Position bag over the opening of the

adapter and hook bag latch over stud. See Figure 4.

FIGURE 4

STEP 5: Hook grass bag handles over the bag

support. See Figure 6.

FIGURE 6

STEP 6: Tilt mower back on its rear wheels for

access to the blade. Place safety blocks underneath

to prevent the machine from falling. Do not tilt

mower with spark plug or carburetor down. Remove

retaining cap screws, lock washers, nuts and cutting

blade. Install both airlifts to the ends of blade and

secure with machine screws, lock washers and nuts.

Torque to 20 to 30 ft. lbs. Reinstall blade, nuts, lock

washers and cap screws. Torque to 20 to 30 ft. lbs.

See Figure 7. Place machine back on all wheels.

FIGURE 7

PARTS IDENTIFICATION

PART No. DESCRIPTION

7-2175 BAG, Grass

7-2903 RING, Connector

2-7670 WIRE, Front Bag

3-8336 HANDLE, Adapter

3-8337 LATCH, Connector

9-0289 NUT, 3/8-24 Hex Center Lock

9-0803 BOLT, 1/4-20 x 5/8” Carriage (6)

9-1065 NUT, 1/4-20 Hex Flange Lock (6)

5-1906 ASSEMBLY, Grass Bag Wire

5-8619 ASSEMBLY, Adapter Chute

1-1763 WASHER, 5/16 Fender

9-0477 NUT, 1/4-20 Hex Flange Top Lock

9-0847 SCREW, 1/4-20 x 3/4” Machine

1-0916 SPACER 1/4 x 5/16

9-0541 SCREW, 1/4-28 x 3/4” Hex Cap (2)

9-1024 NUT, 1/4-28 Hex (7)

9-1098 WASHER, 5/16 Flat (2)

9-0112 SCREW, 1/4-28 x 2 Hex Cap (5)

9-1023 WASHER, 1/4 Internal Tooth Lock (7)

1-5969 SPACER, 1/4 x 41/64

3-1724 LIFT, Air (2)

9-0228 SCREW, 5/16-24 x 21/32 Machine (4)

9-0223 NUT, 5/16-24 Hex (4)

9-0391 WASHER, 5/16 Internal Tooth Lock (4)

7-2733 CAP, Plastic

7-2193 TUBING, Bag Support

INSTRUCTION No. 7-2194 (I.R. 5/14/99)

AIR LIFT INSTALLATION

AIR LIFT

TIP OF

BLADE

1724

9-0228

0391

0223

HOOK GRASS BAG

HANDLES OVER

THE BAG SUPPORT

HOOK BAG LATCH

OVER ADAPTER STUD

Simplicity 63086 User manual

Brand: Simplicity

Model: 63086

Category: Lawnmowers

Type: User manual

Download PDF

report

Simplicity 63086 User manual

Simplicity 63086 User manual

Related papers

Other documents