Alpha Alpha SY Boiler Installation guide

Brand: Alpha

Model: Alpha SY Boiler

Type: Installation guide

This manual is also suitable for

Alpha CB Boiler

Alpha Alpha SY Boiler

The Alpha Alpha SY Boiler is a highly efficient and reliable boiler that is perfect for heating your home. It is easy to install and use, and it comes with a variety of features that make it a great choice for any homeowner.

Some of the features of the Alpha Alpha SY Boiler include:

High efficiency: The Alpha Alpha SY Boiler has a high efficiency rating of up to 93%, which means that it will save you money on your energy bills.
Easy to install: The Alpha Alpha SY Boiler is easy to install, and it can be done by a qualified professional in a matter of hours.
Compact design: The Alpha Alpha SY Boiler is compact in size, so it can be installed in even the smallest of spaces.

Alpha Alpha SY Boiler

Some of the features of the Alpha Alpha SY Boiler include:

High efficiency: The Alpha Alpha SY Boiler has a high efficiency rating of up to 93%, which means that it will save you money on your energy bills.
Easy to install: The Alpha Alpha SY Boiler is easy to install, and it can be done by a qualified professional in a matter of hours.
Compact design: The Alpha Alpha SY Boiler is compact in size, so it can be installed in even the smallest of spaces.

Installation Instructions

Alpha CB/C/SY Boiler

Vertical Flue Terminal Assembly

Concentric (60/100) Flue System

(Kit Part No. 6.1000350)

KIT CONTENTS

1. GENERAL

a. The flue system must be installed in accordance with BS 5440:1;1990.

b. The boiler must be installed in accordance with the Installation

instructions supplied with the boiler.

c. The vertical flue terminal assembly is equivalent to a 1 m length of

flue.

d. Each 45° bend is equivalent to a 0.5 m length of flue.

Note: A 90° bend must not be used with the vertical flue.

e. Refer to the vertical flue options (Fig. 4) and ensure the flue length

does not exceed the equivalent of 4 m (including the terminal

assembly).

f. Additional flue lengths of 0.75 m and 1.0 m are available for extending

the flue up to a maximum equivalent flue length of 4 m (including the

terminal assembly).

g. The vertical flue terminal assembly may be connected directly to the

boiler adaptor.

h. To determine the actual length of flue required (L), measure the

distance from the top of the side panel to the weathering slate position

and subtract 640 mm for the terminal assembly, i.e. L = A - 640 mm

(see Fig. 4).

i. When the flue length is more than 2.5 m, the flue restrictor (Fig. 1) must

be removed. - remove the screw securing it in the boiler adaptor and lift

out.

2. INSTALLATION

a. When the template is on the wall in the boiler position, continue the

vertical line from the centre of the flue hole to the roof/ceiling position.

Mark the centre position of the flue hole 215 mm from this line as shown in Fig. 2.

Fig. 1

Fig. 2

Compiled and designed by Publications 2000, Tel (01670) 356211 08/04/D131

Fig. 4

b. Cut a hole and/or remove tiles so that there is at least a 150

mm diameter hole in the roof. Ensure there is at least a 25

mm gap between the outer duct and any combustible

material.

c. Fit a 125 mm diameter weathering slate over the hole in the

roof. A suitable weathering slate (Part No. 6.1000380) is

available from Alpha Therm Ltd.

d. Position the vertical terminal assembly into the weathering

slate ensuring that the slate is located under the lip of the

terminal as shown in Fig. 3.

Note: Ensure that the minimum distances are maintained

(see Fig. 4). Do not secure the terminal into position at this

stage.

e. Assemble the flue ducts together and cut the outer air duct

and inner flue duct assemblies to the correct lengths, i.e. up

to the terminal.

f. Place the inner duct into the outer duct and fit the ducts to

the boiler, as shown in Fig. 3, using the clamps supplied.

g. Connect the terminal ducts to the flue assembly, as shown

in Fig. 3. Secure the inner ducts with the clamps supplied

before locating the outer duct clamp.

h. After assembling all of the ducts, check that the terminal is

correctly located above the roof.

Note: Ensure that the flue assembly is supported at roof

level using suitable brackets, and that the weathering slate

is fitted correctly.

Fig. 3

These instructions have been carefully prepared but we reserve the right to

alter the specification at any time in the interest of product improvement.

Alpha Therm Limited.

Nepicar House, London Road, Wrotham Heath,

Sevenoaks, Kent TN15 7RS

Technical Helpline: 0870 3001 964

email: info@alphatherm.co.uk

website: www.alpha-innovation.co.uk

Alpha Alpha SY Boiler Installation guide

Brand: Alpha

Model: Alpha SY Boiler

Type: Installation guide

This manual is also suitable for

Alpha CB Boiler

Alpha Alpha SY Boiler

Some of the features of the Alpha Alpha SY Boiler include:

High efficiency: The Alpha Alpha SY Boiler has a high efficiency rating of up to 93%, which means that it will save you money on your energy bills.
Easy to install: The Alpha Alpha SY Boiler is easy to install, and it can be done by a qualified professional in a matter of hours.
Compact design: The Alpha Alpha SY Boiler is compact in size, so it can be installed in even the smallest of spaces.

Download PDF

report

Alpha Alpha SY Boiler Installation guide

This manual is also suitable for

Alpha Alpha SY Boiler Installation guide

Related papers

Other documents