Astonica 40200806 User manual

Brand: Astonica

Model: 40200806

Type: User manual

Model No. 40200806

Three Tier Fountain

Instruction Manual

231012rev2

Read the instructions and precautions before use of this product

Please keep this instruction manual for future reference

For warranty information, please refer to the back page of

this instruction manual.

Due to ongoing product development

the actual product or products may vary from

the illustrations or photos shown within this manual.

NOTE: This product is intended for residential, non-commercial use.

Made in China

Distributed by:

World Factory, Inc.

Westlake, TX 76262

For Manuals, Replacement Parts or Customer Service visit:

www.ezreplacement.com

Limited Warranty

World Factory, Inc. Products for Home Use

World Factory, Inc. (Seller) warrants to the original Buyer only, that each Astonica Product will be free

from defects in material and workmanship for a period of one (1) year from date of purchase.

SELLER’S SOLE OBLIGATION AND BUYER’S EXCLUSIVE REMEDY UNDER THIS LIMITED

WARRANTY SHALL BE THE REPAIR OR REPLACEMENT OF PARTS, WITHOUT CHARGE, WHICH

ARE DEFECTIVE IN MATERIAL OR WORKMANSHIP. ANY PARTS AS DETERMINED BY THE SELLER

WHICH HAVE BEEN MISUSED; ABUSED OR DAMAGED EITHER DIRECTLY OR INDIRECTLY FROM

REPAIRS OR ALTERATIONS ATTEMPTED BY UNAUTHORIZED PERSONS; IMPROPER

MAINTENANCE, NEGLECT OR ACCIDENT ARE NOT COVERED BY THIS LIMITED WARRANTY. This

warranty does not apply to damage, heat-induced coloration changes, scratching or alteration due to

normal use or weathering. To make a claim under this Limited Warranty, you must return the complete

product with proof of purchase, transportation prepaid, to any World Factory, Inc. authorized service

center. Call 1-888-422-7800 or visit: ezreplacement.com for the location of the nearest authorized

service center.

Additional Limitations

THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY OR CONSUMABLE ITEMS RELATED

TO THIS PRODUCT. ALL IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE (1)

YEAR FROM DATE OF PURCHASE. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL

OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF

PROFITS, ARISING FROM THE SALE OR USE OF THIS PRODUCT.

If any provision of this Limited Warranty is for any reason held to be invalid or unenforceable, such

provision shall not affect any other provision herein, this Limited Warranty shall be construed as if

such invalid and/or unenforceable provision had never been contained herein.

This warranty gives you special legal rights, and you may also have other rights which vary from state

to state.

This Warranty contains the entire agreement between Seller and Buyer and supersedes any and all

prior agreements, arrangements, or understandings between the parties relating to product warranty.

WARNING! ELECTRICAL SHOCK. Read and understand all instructions. Failure to follow all

instructions listed below, may result in electrical shock, ﬁre and/or serious personal injury.

SAVE THESE INSTRUCTIONS.

Grounding Instructions

This fountain must be plugged into a 3-wire, 3-prong outlet that is properly working and has

been installed and grounded in accordance with all local, state or federal codes and ordinances.

DANGER: IMPROPER INSTALLATION OF THE GROUNDING PLUG CAN RESULT IN A RISK OF

ELECTRICAL SHOCK. Check with a qualiﬁed electrician or serviceman if the grounding instructions

are not completely understood, or if doubt as to weather the product is properly grounded. Do not

modify the plug provided; if it will not ﬁt the outlet, have a proper outlet installed by a qualiﬁed

electrician. Do not use any type of adapter with this product.

Adjust Speed of Water Flow

1. Unplug pump (H) from AC power outlet.

2. Move adjustment switch on pump (H)

toward "+" positive to increase water

ﬂow, or "-" to decrease water ﬂow.

Maintenance

1. Check water level periodically, add

water if necessary.

2. If water is not ﬂowing, check electric pump (H),

and the clear tubing (K) for clogs.

NOTE: Pump may build up calcium after a

long period of time and stop running when

tap water is used. Any calcium remover can

be used to clean pump.

ELECTRICAL SAFETY INSTRUCTIONS

Grounded

Outlets

AMP Load Volts Extension Cord Length

120V 25' 50' 100' 150'

AWG

1-5 18 16 16 14

6-10 18 16 14 12

10-12 14 14 14 12

12-16 14 12

Not recommended

Table 1. Minimum Recommended Extension Cord Gauge (AWG) Chart

Outdoor Use Extension Cords

1. When product is used outdoors, use only extension cords marked for outdoor use.

2. Use only UL listed extension cords. Never use damaged or altered extension cords.

3. Follow extension cord manufacturer safety instruction.

Extension Cords

1. Make sure your extension cord is in good condition.

2. When using extension cords, be sure to use one heavy enough to carry the current your product

requires. An undersized cord will cause a drop in line voltage resulting in power loss and

overheating. Reference Table 1 at the bottom of the page for the correct size to use depending

on cord length and nameplate Ampere rating. If in doubt, use the next heavier gage. The smaller

the gage number, the heavier the cord.

Figure 3

Figure 4

3. (SEE FIGURE 3) Connect parts (D) medium

basin, (E) top pedestal and (F) small basin

together. Thread the PVC tube from ﬁnial

top (G) through the fountain assembly of

parts (D, E & F).

4. Taking the fountain assembly, thread the PVC

tube into the center pedestal (C) align the tabs

and notches of the fountain assembly and

secure by twisting.

5. With help, carefully lift the fountain assembly

slightly, ﬁnd the PVC tube, and connect the

PVC tube to the top of the electric pump spout.

Align the tabs and notches and secure the

complete fountain assembly by twisting.

6. Plug the light connectors from the light ring (I)

to the connectors from the electric pump (H),

and then push them into the center pedestal

and under the light ring to hide and secure the

door (retained from step 2) back on the base

of the center pedestal (C).

Basin Tab

Pedestal

Notch

7. (SEE FIGURE 4) Fill the large basin (A) with

water; if possible use distilled water to ﬁll

the fountain.

8. Plug the power cord from the transformer (J)

into properly grounded 120V AC outlet.

ASSEMBLY INSTRUCTIONS

NOTE: Tabs and notches on fountain parts are

different sizes and must be matched up

correctly to secure.

1. (SEE FIGURE 1) Place the base pedestal (A) on

ﬂat, level surface. Put the large basin (B) on

the base pedestal (A) aligning the tabs of the

basin with the notches in the top of the base.

Turn the large basin counter clockwise to lock

into place. Place the electric pump (H) into the

center ring in the bottom of the large basin (B)

beside the PVC tube. Thread the power cord of

the pump (H) through the PVC tube, the

pedestal base (A) and out the bottom of the

base as shown. Connect the male end of the

power cord from pump (H) to the female

connector of the transformer (J).

Figure 1

Figure 2

A Base Pedestal 1

B Large Basin 1

C Center Pedestal 1

D Medium Basin 1

E Top Pedestal 1

F Small Basin 1

G Finial Top 1

H Electric Pump 1

I Light Ring 1

J Transformer 1

PARTS & HARDWARE LIST

PART #

DESCRIPTION QUANTITY

Carefully remove the contents from the package. If any parts are missing do not

attempt to use the product until they have been obtained and correctly installed.

Parts Detail

Basin Tab

Base Notch

Power Cord

2. (SEE FIGURE 2) Place the light ring (I) in the

bottom of the large basin (B). Remove the door

of the center pedestal (C) located at the base

of the pedestal. Thread the light connector

cords from the electric pump through the door

opening and out. Align the tabs and notches

and set the center pedestal (C) on the large

basin. Do not secure yet.

Door

Basin Tab

Light Connectors

Astonica 40200806 User manual

Astonica 40200806 User manual

Astonica 40200806 User manual

Related papers

Other documents