Tu r n s p i t
For utilizzation of the turnspit follow the instructions
described.
Put the food in spit L (see fig. 4), paying attention to
block it within the two forks F and to balance it, in order
to avoid any unnecessary effort in motor R.
Put the spit on support G, after having put its opposite
end into hole P of motor R.
Place the drip-tray with a little water under the spit.
To remote the spit, operate in the opposite direction
using protecting glove in isolating wool.
The turnspit can be operated turning the knob clockwise
on position .
DIGITAL TIMER - INSTRUCTIONS FOR USE
Main Characteristics
24 hour clock with automatic programme and timer.
Functions
Cooking time, cooking end, manual position, clock,
timer, time programmable up to 23 hours 59 minutes.
Display
Fluorescent 4-digit display with 7 sections indicating time
and cooking times.
Cooking time or manual function = pot symbol
Automatic function = AUTO
Timer = bell symbol
The corresponding symbol of the function selected lights up.
Programming
To programme cooking, press the button of the desired
function then, within five seconds of pressing it, start
setting the time with buttons + and -.
Button + and -
Press buttons + and - to increase or decrease the time.
The speed of the increase/decrease depends on how
long the button is kept pressed.
Setting the time
Press the two buttons (manual and + or - ) at the same
time to set the time. Setting the time cancels any previously
set programmes and the relay contacts are deactivated.
Manual operation
Press the manual button, the relay contacts are shut, the
AUTO symbol switches off, the pot symbol lights up.
Manual operation is only possible at the end of automatic
programming or after cancelling it.
Automatic operation
When the cooking time or cooking end button is
pressed, the programmer automatically switches from
manual to automatic operation.
Semi-automatic operation with cooking time
Press the cooking time button and set the desired time
using + or -. The AUTO symbol lights up and remains lit,
as does the cooking time symbol. The relay is
immediately activated.
When cooking end time coincides with the time, the
relay and the cooking time symbol are deactivated, the
acoustic signal sounds and the AUTO symbol flashes.
Semi-automatic operation with cooking end
Press the cooking end button. The display shows the
current time. Select the desired cooking end time using
the button +. The AUTO and cooking time symbols light
up and remain lit. The relay contacts are activated.
When cooking end time coincides with the time, the
relay and the cooking time symbol are deactivated. At
the end of cooking time, the AUTO symbol flashes, the
acoustic signal sounds and both the cooking time symbol
and the relay are deactivated.
Automatic operation with cooking time and
cooking end
Press the cooking time button and select the desired
cooking time using + or -. The AUTO and cooking time
symbols light up and remain lit.
The relay is activated. Press the cooking end button. The
display shows the earliest cooking end time. Select the
desired cooking end using button +. The relay and the
cooking time symbol are deactivated. The symbol lights
up again when the time coincides with cooking start
time. At the end of cooking time, the AUTO symbol
flashes. The acoustic signal sounds and both the cooking
time symbol and the relay switch off.
Timer
Press the timer button and select the desired cooking
time using + or -.
During timer operation the bell symbol remains lit.
At the end of the set time, the acoustic signal sounds and
the bell symbol switches off.
Acoustic signal
The acoustic signal sounds at the end of a programme
and at the end of the timer function, remaining in
operation for 15 minutes. To halt the acoustic signal,
press any of the function buttons.
Programme start and check
The programme starts approx. 4 seconds after setting.
You can check the set programme at any time by
pressing the relative button.
Programming error
A programming error is signalled if the time on the clock
is between the start of cooking time and cooking end
time. The setting error can be corrected by changing
cooking time or cooking end time. In the event of a
programming error the relays are deactivated.
Cancelling a programme
To cancel a programme, press the cooking time button
followed by the button - until the display shows 00 00. At
the end of a set programme, this is automatically cancelled.
1
2
3
4
5
Number of shelves
fig. 4
A
U
T
O
Timer
Cooking time
Cooking end
Manual
Decrease time
Add time