Whirlpool AWO/D 6927 S WP Program Chart

Type
Program Chart
GB PROGRAMME CHART
5019 301 06182
Whirlpool is a registered trademark of Whirlpool USA
:
optional / Yes : dosing required
1)
For improved garment care, spin speed is restricted in these programmes.
The wool and handwash cycles of this machine have been tested and approved by The Woolmark Company for the washing of
Woolmark garments labelled as “machine wash” or “handwash” provided that the garments are washed according to the
instructions on the garment label and those issued in this programme chart. M0512
Programme
Tempe-
rature
Care
Labels
Max
Load
kg
Type of wash/Notes
- Respect the manufacturer’s recommendations on the care label
Detergents and additives Special options
Max
Spin
Speed
rpm
Pre-
wash
Main
wash
Softener Pre-
wash
Start
delay
Easy
ironing
Intensive
rinse
Rinse
hold
Variable
spin
70 - 95 °C
7.0
Normally to heavily soiled bed linen, table linen and underwear, towels, shirts
etc. made of cotton and linen.
At a temperature of 80°C or more, this programme eliminates bacteria,
ensuring sanitization of your laundry. The bacteria removal efficiency has been
tested following a similar methodology to the NF EN 13697 standard of
Nov. 2001.
Yes
❉❉
max.
Coloured Cotton
20 - 60 °C
7.0
Synthetics
20 - 60 °C
3.0
Normally soiled blouses, shirts, overalls etc. made of polyester (Diolen,
Trevira), polyamide (Perlon, Nylon) or blends with cotton.
Yes
❉❉
max.
Daily load
20 - 60 °C
4.0
Slightly to normally soiled textiles made of cotton and/or synthetics.
Yes
——
❉❉
max.
20 - 30 °C
4.0
Shortly worn outer clothing made of cotton, polyester, polyamide and blends
with cotton.
Yes
——
——
❉❉
max.
Delicates
20 - 40 °C
1.5
Curtains and delicate clothing, dresses skirts, shirts and blouses.
Yes
❉❉
——
❉❉
1000
1)
20 - 60 °C
7.0
Slightly to normally soiled bed linen, table linen and underwear, towels, shirts
etc. made of cotton and/or linen.
Offers highest economy in energy consumption by prolonged wash duration. Ideal
to be run overnight to additionally profit from the more favourable energy rates. To
avoid noise of spinning at night, set spin speed to “0” and start spin programme in
the morning, or define programme start with “Start Delay” accordingly.
Yes
——
❉❉
max.
Lingerie
20 - 30 °C
1.0
This programme is particularly suitable to treat delicate lingerie (use of a
laundry net strongly recommended).
Yes
——
——
❉❉
400
1)
Wool
20 - 40 °C
1.0
Only woollens, labelled with the Woolmark and identified as machine
washable.
This programme (40°C) is tested and approved by The Woolmark Company
for machine washable wool.
Yes
——
——
❉❉
1000
1)
20 - 40 °C
1.0
Textiles made of linen, silk, wool and viscose marked as “handwashable”.
This programme (40°C) is tested and approved by The Woolmark Company
for handwashable wool.
Yes
——
——
❉❉
400
1)
Rinse & Spin
——
7.0
Same as the last rinse and the final spin in the “Cotton” programme.
——
——
❉❉
max.
Spin
——
7.0
In this programme spinning is intensive. Same as the spin cycle in the “Cotton
programme.
——
——
max.
Gentle Spin
——
1.0
In this programme spinning is gentle. Same as the spin cycle in the “Wool”
programme.
——
——
1000
1)
Drain
——
Drain only - no spinning. Alternative method of terminating programme after
“Rinse Hold”.
——
——
A. “Door open” indication
This washing machine is equipped with
automatic safety functions which
detect and diagnose faults at an early
stage and react appropriately, e.g.:
B. “Service” indication
C. “Water tap closed” indication
D. “Clean pump” indication
E. Programme selector
F. “Start (Pause)” button
G. “Variable spin” button
H. Programme sequence indicator
I. “Reset” button
J. “Start delay” button
K. “Temperature” button
L. Display
D
H
C
F
I
G
E
B
A
J L
}
K
30106182GB.fm Page 1 Thursday, May 8, 2008 5:08 PM
Black process 45.0° 100.0 LPI
5019 301 06182
Whirlpool is a registered trademark of Whirlpool USA
Add detergent as indicated on the front page and as
described in the chapter “Detergent and Additives” in
your Instructions for Use.
1. Turn the
programme selector
to the desired
programme. The display shows the programme
duration in hours and minutes as well as the
predefined temperature. The
“Start (Pause)”
button blinks.
2. The
temperature
can be altered by pressing the
“Temperature” button.
3. The indication lamp of the predefined
spin speed
lights up; in case you want to set another spin speed,
press the “Variable spin” button.
Push the button of any option desired - the respective
indication lights up.
When the combination of programme and additional
option(s) is not possible, the indication lights switch off
automatically. Unsuitable combinations of options are
deselected automatically.
“Clean+” button
Choose this option if you use an in-wash additive for
stain removal (powder, for example “Vanish”) - it will
optimize the additive’s efficiency to get better wash
performance and stain removal.
Selectable for programmes “Cotton” and “Synthetics”;
choose temperature of 30 or 40°C and use with
maximum load.
Add an appropriate amount of in-wash additive for
stain removal (powder) to the main wash chamber,
together with your detergent (only use powder
detergent with this option). Respect the
manufacturer’s dosing instructions.
Prolongs the programme by approx. 10 to 15 minutes.
Appropriate for use of stain removers and bleaches on
oxygen basis.
Chlorine or perborate bleaches must
not be used!
“Prewash” button
Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time by
approximately 15 min.
Do not use liquid detergent for the main wash when
activating the Prewash option.
“Easy ironing” button
Can be used together with “Cotton”, “Synthetics” and
“Daily load” programmes to make ironing easier.
Increases the water quantity and the clothes are spun
very gently.
“Intensive rinse” button
More water is added and rinse cycle is prolonged.
This option is particularly suitable for areas with very
soft water, washing baby linen and helps people with
allergies.
“Rinse hold” button
The laundry remains in the last rinse water without
progressing to the final spin cycle to avoid creasing and
prevent colours from changing.
This option is particularly recommended for the
programmes “Synthetics”, “Daily load” and “Delicates”.
It is particularly useful if you want to postpone spinning
to a later time, or if you want to drain only.
If you select “Rinse hold”, do not leave the laundry to
soak for too long.
CONSUMPTION DATA
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme Duration
(hours : minutes)
*
95 7.0 74
**
2.10 2:10
Coloured Cotton
***
60 7.0 54 1.19 2:20
Coloured Cotton 40 7.0 69 0.75 2:05
Synthetics 60 3.0 46
**
0.80 1:35
Synthetics 40 3.0 42 0.40 1:20
Daily load 40 4.0 48 0.50 1:00
30 4.0 48 0.25 0:30
Delicates 30 1.5 60 0.50 0:45
60 7.0 69 0.84 4:00
Lingerie 30 1.0 45 0.45 0:40
Wool 40 1.0 60 0.55 0:45
40 1.0 45 0.55 0:40
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home
may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
*
The time indicated on the display can deviate from the values in the table, because it takes into account the household conditions
applicable at that time.
**
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
***
Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
Note:
The programme stops to “Rinse hold” at the
time the “Rinse hold” light in the programme sequence
indicator is on. The indication lamp next to the
“Start
(Pause)”
button blinks.
Terminate the “Rinse hold” option:
Press the
“Start (Pause)”
button; the programme
will terminate automatically with the final spin cycle for
the present wash programme.
If you do not wish to spin the clothes, turn the
programme selector knob to the “Drain” programme
and press the
“Start (Pause)”
button.
Variable spin” button
Every programme has a predefined spin speed.
Press the button to set another spin speed.
If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain during
rinse. The water is drained out only.
The “Start Delay” allows to run the machine at the consumer’s
convenience, for example at night when electricity is cheaper.
Do not use liquid detergent when activating the “Start Delay”.
Select programme, temperature and options.
Press the “Start Delay” button to select the delay time
by 1 to 23 hours;
Press the
“Start (Pause)”
button.
The indication light next to the “Start Delay” button
lights up and the countdown of the delay time begins.
The dot between hours and minutes of the indicated
delay time as well as the light of the start delay button
will keep blinking until the programme starts.
The time delay indication disappears when the
programme starts and it is replaced by the remaining
programme time.
Once having pressed the
“Start (Pause)”
button, the
number of hours preselected can be reduced by
pressing and holding the “Start Delay” button. From 1
hour on, the delay time can also be reduced by minutes.
To cancel the “Start Delay
..before you press the “Start (Pause)” button:
Turn the programme selector to another position or
press the
“Reset”
button.
..after having pressed the “Start (Pause)” button:
Press the
“Reset”
button for at least 3 seconds - the
start delay time disappears from the display.
Open the tap and press the
“Start (Pause)”
button. The
indication lamp next to the
“Start (Pause)”
button lights
up. The programme sequence indicator shows the current
programme phase, running from left to right through
Wash, Rinse, Spin/Drain.
The display shows the remaining programme time. Due to
variations in load and temperature of inlet water, the remaining
time is newly calculated in certain programme phases. If this is
the case,
an animation appears on the display
.
Before starting and after end of a programme, the lamp
lights to show that the door can be opened. As long as a
wash programme is running, the door remains locked and
must on no account be forced open. In case you have an
urgent need to open it during a running programme, refer
to “Cancel (Reset) a running programme before the end”.
“Service”
Lighting up of the “Service” indication can be caused by a
fault in an electrical component. Refer to the
“Troubleshooting Guide” in your Instructions for Use; if
the fault persists, contact our After Sales Service.
“Water tap closed”
The appliance has no or insufficient water supply. Open
the water tap; if the indication still lights up, refer to the
“Troubleshooting Guide” in the Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the drain
hose is kinked or the filter must be cleaned; in the latter case
refer to the Instructions for Use (“Removing the Filter”).
All the lights of the programme sequence indicator
are off, and the “Door open” indication lights up.
1. Turn the programme selector to the “Off/O” position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
1. Press the
“Start (Pause)”
button to pause the
programme. The light blinks.
2. Select the new programme, temperature, any options
and another spin speed if you want.
3. Press the
“Start (Pause)”
button again. The new
programme continues at the same position where the
previous programme was interrupted. Do not add
detergent for this programme.
The
“Reset”
button cancels a programme before the end.
Press the
“Reset”
button for at least 3 seconds. Any
existing water is drained out before the door can be
opened.
START DELAY
PROGRAMME START
“DOOR OPEN” INDICATION
RED INDICATIONS
PROGRAMME END
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
30106182GB.fm Page 2 Thursday, May 8, 2008 5:08 PM
Black process 45.0° 100.0 LPI
  • Page 1 1
  • Page 2 2

Whirlpool AWO/D 6927 S WP Program Chart

Type
Program Chart

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI